参数资料
| 型号： | LT1102IN8 |
| 厂商： | Linear Technology |
| 文件页数： | 11/12页 |
| 文件大小： | 0K |
| 描述： | IC PREC INSTRMNT-AMP JFET 8-DIP |
| 标准包装： | 50 |
| 放大器类型： | 仪表 |
| 电路数： | 1 |
| 转换速率： | 30 V/µs |
| 增益带宽积： | 3.5MHz |
| 电流 - 输入偏压： | 4pA |
| 电压 - 输入偏移： | 200µV |
| 电流 - 电源： | 3.4mA |
| 电压 - 电源，单路/双路(±)： | ±9 V ~ 18 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 8-PDIP |
| 包装： | 管件 |
LT1102
8
1102fb
In the two op amp instrumentation amplifier configura-
tion, the first amplifier is basically in unity gain, and the
second amplifier provides all the voltage gain. In the
LT1102, the second amplifier is decompensated for gain
of 10 stability, therefore high slew rate and bandwidth are
achieved. Common mode rejection versus frequency
is also optimized in the G = 10 mode, because the
bandwidths of the two op amps are similar. When G = 100,
this statement is no longer true; however, by connecting
an 18pF capacitor between pins 1 and 2, a common mode
AC gain is created to cancel the inherent roll-off. From
200Hz to 30kHz, CMRR versus frequency is improved by
an order of magnitude.
Input Protection
Instrumentation amplifiers are often used in harsh
environments where overload conditions can occur.
The LT1102 employs FET input transistors, consequently
the differential input voltage can be
±30V (with ±15V
supplies,
±36V with ±18V supplies). Some competitive
instrumentation amplifiers have NPN inputs which are
protected by back-to-back diodes. When the differential
input Voltage exceeds
±13Vonthesecompetitivedevices,
input current increases to milliampere level; more than
±10V differential voltage can cause permanent damage.
When the LT1102 inputs are pulled below the negative
supply or above the positive supply, the inputs will clamp
a diode voltage below or above the supplies. No damage
will occur if the input current is limited to 20mA.
Common Mode Rejection Ratio
vs Frequency
Gains Between 10 and 100
Gains between 10 and 100 can be achieved by connecting
two equal resistors (= RX) between pins 1 and 2 and pins
7 and 8.
The nominal value of R is 1.84k
Ω. The usefulness of this
method is limited by the fact that R is not controlled to
better than
±10% absolute accuracy in production.
However, on any specific unit, 90R can be measured
between Pins 1 and 2.
APPLICATIO S I FOR ATIO
WU
UU
Gain = 10 +
RX
R + RX/90
FREQUENCY (Hz)
1
0
COMMON
MODE
REJECTION
RATIO
(dB)
20
40
60
80
120
10
100
1k
10k
100k
1M
100
LT1102 AI01
VS = ±15V
TA = 25°C
G = 100
18pF PIN 1
TO PIN 2
G = 10
G = 100
相关PDF资料 |
PDF描述 |
|---|---|
| 0234001.MXBP | FUSE 5X20 C/CODE M 1A/250V |
| LT1102IN8#PBF | IC PREC INSTRMNT-AMP JFET 8-DIP |
| 0234002.MXBP | FUSE 5X20 C/CODE M 2A/250V |
| LT1795ISW#PBF | IC AMP CURR FEEDBACK DUAL 20SOIC |
| AD744AQ | IC OPAMP BIFET 13MHZ PREC 8CDIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1102IN8#PBF | 功能描述:IC PREC INSTRMNT-AMP JFET 8-DIP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:150 系列:- 放大器类型:音频 电路数:2 输出类型:- 转换速率:5 V/µs 增益带宽积:12MHz -3db带宽:- 电流 - 输入偏压:100nA 电压 - 输入偏移:500µV 电流 - 电源:6mA 电流 - 输出 / 通道:50mA 电压 - 电源，单路/双路(±):4 V ~ 32 V，±2 V ~ 16 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| LT1102M | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Speed, Precision, JFET Input Instrumentation Amplifier(Fixed Gain=10 or 100) |
| LT1102MH | 制造商:Linear Technology 功能描述:SP Amp INSTR Amp Single ±20V 8-Pin TO-5 |
| LT1102MJ8 | 制造商:Linear Technology 功能描述:SP Amp INSTR Amp Single 制造商:Linear Technology 功能描述:SP Amp INSTR Amp Single ±20V 8-Pin CDIP |
| LT1103 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Offline Switching Regulator |
发布紧急采购，3分钟左右您将得到回复。