参数资料
| 型号： | LT1121CST-5#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 4/16页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 5V .15A SOT223-3 |
| 产品培训模块： | More Information on LDOs |
| 标准包装： | 78 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 5V |
| 输入电压： | 最高 30V |
| 电压 - 压降（标准）： | 0.42V @ 150mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 150mA |
| 工作温度： | 0°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | TO-261-4，TO-261AA |
| 供应商设备封装： | SOT-223 |
| 包装： | 管件 |
| 产品目录页面： | 1326 (CN2011-ZH PDF) |
LT1121/LT1121-3.3/LT1121-5
ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T A = 25°C.
PARAMETER
Ground Pin Current (Note 7)
Adjust Pin Bias Current (Notes 5, 8)
CONDITIONS
I LOAD = 0mA
I LOAD = 1mA
I LOAD = 10mA
I LOAD = 50mA
I LOAD = 100mA
I LOAD = 150mA
T J = 25oC
l
l
l
l
l
l
MIN
TYP
30
90
350
1.5
4
7
150
MAX
50
120
500
2.5
7
14
300
UNITS
μA
μA
μA
mA
mA
mA
nA
Shutdown Threshold
Shutdown Pin Current (Note 9)
V OUT = Off to On
V OUT = On to Off
V SHDN = 0V
l
l
l
0.25
1.2
0.75
6
2.8
10
V
V
μA
Quiescent Current in Shutdown (Note 10) V IN = 6V, V SHDN = 0V
l
16
22
μA
Ripple Rejection
V IN – V OUT = 1V (Avg), V RIPPLE = 0.5V P-P , f RIPPLE = 120Hz,
I LOAD = 0.1A
50
58
dB
Current Limit
Input Reverse Leakage Current
Reverse Output Current (Note 11)
V IN – V OUT = 7V, T J = 25oC
V IN = –20V, V OUT = 0V
LT1121-3.3 V OUT = 3.3V, V IN = 0V
LT1121-5 V OUT = 5V, V IN = 0V
LT1121 (Note 5) V OUT = 3.8V, V IN = 0V
l
200
16
16
16
500
1
25
25
25
mA
mA
μA
μA
μA
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The shutdown pin input voltage rating is required for a low
impedance source. Internal protection devices connected to the shutdown
pin will turn on and clamp the pin to approximately 7V or – 0.6V. This
range allows the use of 5V logic devices to drive the pin directly. For high
impedance sources or logic running on supply voltages greater than 5.5V,
the maximum current driven into the shutdown pin must be limited to less
than 20mA.
Note 3: For junction temperatures greater than 110°C, a minimum load
of 1mA is recommended. For T J > 110°C and I OUT < 1mA, output voltage
may increase by 1%.
Note 4: Operating conditions are limited by maximum junction
temperature. The regulated output voltage specification will not apply
for all possible combinations of input voltage and output current. When
operating at maximum input voltage, the output current range must be
limited. When operating at maximum output current the input voltage
range must be limited.
Note 5: The LT1121 (adjustable version) is tested and specified with the
adjust pin connected to the output pin.
Note 6: Dropout voltage is the minimum input/output voltage required to
maintain regulation at the specified output current. In dropout the output
voltage will be equal to: (V IN – V DROPOUT ).
Note 7: Ground pin current is tested with V IN = V OUT (nominal) and a
current source load. This means that the device is tested while operating in
its dropout region. This is the worst case ground pin current. The ground
pin current will decrease slightly at higher input voltages.
Note 8: Adjust pin bias current flows into the adjust pin.
Note 9: Shutdown pin current at V SHDN = 0V flows out of the shutdown pin.
Note 10: Quiescent current in shutdown is equal to the sum total of the
shutdown pin current (6μA) and the ground pin current (9μA).
Note 11: Reverse output current is tested with the input pin grounded and
the output pin forced to the rated output voltage. This current flows into
the output pin and out of the ground pin.
1121fg
4
相关PDF资料 |
PDF描述 |
|---|---|
| MCP1804T-3002I/DB | IC REG LDO 3V .15A SOT223-3 |
| 420QXW180MEFC18X40 | CAP ALUM 180UF 420V 20% RADIAL |
| LT1580CT7-2.5 | IC LDO REGULATOR 7A 2.5V TO220-7 |
| MIC29301-5.0WT | IC REG LDO 5V 3A TO220-5 |
| 420CXW180MEFC18X40 | CAP ALUM 180UF 420V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1121CZ-3.3 | 功能描述:IC REG LDO 3.3V .15A TO92-3 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.3V 输入电压:2.5 V ~ 5.5 V 电压 - 压降（标准）:0.1V @ 200mA 稳压器数量:2 电流 - 输出:300mA 电流 - 限制（最小）:350mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-UFQFN 供应商设备封装:8-MLPQ-UT（1.5x1.5） 包装:剪切带 (CT) 产品目录页面:1358 (CN2011-ZH PDF) 其它名称:SC560HULCT |
| LT1121CZ-3.3#PBF | 功能描述:IC REG LDO 3.3V .15A TO92-3 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.3V 输入电压:2.5 V ~ 5.5 V 电压 - 压降（标准）:0.1V @ 200mA 稳压器数量:2 电流 - 输出:300mA 电流 - 限制（最小）:350mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-UFQFN 供应商设备封装:8-MLPQ-UT（1.5x1.5） 包装:剪切带 (CT) 产品目录页面:1358 (CN2011-ZH PDF) 其它名称:SC560HULCT |
| LT1121CZ-3.3#TR | 功能描述:IC REG LDO 3.3V .15A TO92-3 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.3V 输入电压:2.5 V ~ 5.5 V 电压 - 压降（标准）:0.1V @ 200mA 稳压器数量:2 电流 - 输出:300mA 电流 - 限制（最小）:350mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-UFQFN 供应商设备封装:8-MLPQ-UT（1.5x1.5） 包装:剪切带 (CT) 产品目录页面:1358 (CN2011-ZH PDF) 其它名称:SC560HULCT |
| LT1121CZ-3.3#TRPBF | 功能描述:IC REG LDO 3.3V .15A TO92-3 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.3V 输入电压:2.5 V ~ 5.5 V 电压 - 压降（标准）:0.1V @ 200mA 稳压器数量:2 电流 - 输出:300mA 电流 - 限制（最小）:350mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-UFQFN 供应商设备封装:8-MLPQ-UT（1.5x1.5） 包装:剪切带 (CT) 产品目录页面:1358 (CN2011-ZH PDF) 其它名称:SC560HULCT |
| LT1121CZ5 | 制造商:LT 功能描述:NeW |
发布紧急采购，3分钟左右您将得到回复。