参数资料
| 型号： | LT1121IN8#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 11/16页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO ADJ .15A 8-DIP |
| 产品培训模块： | More Information on LDOs |
| 标准包装： | 50 |
| 稳压器拓扑结构： | 正，可调式 |
| 输出电压： | 3.75 V ~ 30 V |
| 输入电压： | 4.17 V ~ 36 V |
| 电压 - 压降（标准）： | 0.42V @ 150mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 150mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 8-PDIP |
| 包装： | 管件 |
LT1121/LT1121-3.3/LT1121-5
APPLICATIONS INFORMATION
resistor is shown in Table 6. The LT1121 is a micropower
device and output transient response will be a function of
output capacitance. See the Transient Response curves
in the Typical Performance Characteristics. Larger values
of output capacitance will decrease the peak deviations
and provide improved output transient response. Bypass
capacitors, used to decouple individual components
powered by the LT1121, will increase the effective value
of the output capacitor.
Table 6. Suggested Series Resistor Values
OUTPUT CAPACITANCE SUGGESTED SERIES RESISTOR
0.33μF 2 Ω
0.47μF 1 Ω
0.68μF 1 Ω
>1μF None Needed
Protection Features
The LT1121 incorporates several protection features
which make it ideal for use in battery-powered circuits.
In addition to the normal protection features associated
with monolithic regulators, such as current limiting and
thermal limiting, the device is protected against reverse
input voltages, reverse output voltages, and reverse volt-
ages from output to input.
Current limit protection and thermal overload protection
are intended to protect the device against current overload
conditions at the output of the device. For normal opera-
tion, the junction temperature should not exceed 125°C.
short-circuit current of the device and will protect itself by
thermal limiting. For the adjustable version of the device,
the output pin is internally clamped at one diode drop
below ground. Reverse current for the adjustable device
must be limited to 5mA.
In circuits where a backup battery is required, several
different input/output conditions can occur. The output
voltage may be held up while the input is either pulled
to ground, pulled to some intermediate voltage, or is left
open circuit. Current flow back into the output will vary
depending on the conditions. Many battery-powered cir-
cuits incorporate some form of power management. The
following information will help optimize battery life. Table
7 summarizes the following information.
The reverse output current will follow the curve in Figure
2 when the input pin is pulled to ground. This current
flows through the output pin to ground. The state of the
shutdown pin will have no effect on output current when
the input pin is pulled to ground.
In some applications it may be necessary to leave the
input to the LT1121 unconnected when the output is held
high. This can happen when the LT1121 is powered from
a rectified AC source. If the AC source is removed, then
the input of the LT1121 is effectively left floating. The
reverse output current also follows the curve in Figure 2
if the input pin is left open. The state of the shutdown pin
will have no effect on the reverse output current when the
input pin is floating.
80
(V OUT = V ADJ )
Theinputofthedevicewillwithstandreversevoltagesof
30V. Current flow into the device will be limited to less
than 1mA (typically less than 100μA) and no negative
voltage will appear at the output. The device will protect
both itself and the load. This provides protection against
batteries that can be plugged in backwards.
For fixed voltage versions of the device, the output can
be pulled below ground without damaging the device. If
the input is open circuit or grounded the output can be
pulled below ground by 20V. The output will act like an
open circuit, no current will flow out of the pin. If the input
is powered by a voltage source, the output will source the
100
T J = 25 ° C
90 V IN < V OUT
CURRENT FLOWS
INTO OUTPUT PIN
70 TO GROUND
60 LT1121
50
40
LT1121-3.3
30
20
LT1121-5
10
0
0 1 2 3 4 5 6 7
OUTPUT VOLTAGE (V)
8
9 10
1121? F02
Figure 2. Reverse Output Current
1121fg
11
相关PDF资料 |
PDF描述 |
|---|---|
| HMM22DRYN-S13 | CONN EDGECARD 44POS .156 EXTEND |
| NCP4587DMX18TCG | IC REG LDO 1.8V .15A 6-XDFN |
| HSM22DRYH-S13 | CONN EDGECARD 44POS .156 EXTEND |
| GCC65DRES-S734 | CONN EDGECARD 130PS .100 EYELET |
| NCP4587DMX28TCG | IC REG LDO 2.8V .15A 6-XDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1121IS8 | 功能描述:IC REG LDO ADJ .15A 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 产品培训模块:More Information on LDOs 标准包装:50 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.3V 输入电压:最高 15V 电压 - 压降（标准）:1.1V @ 800mA 稳压器数量:1 电流 - 输出:800mA 电流 - 限制（最小）:800mA 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-263-4，D²Pak（3 引线+接片），TO-263AA 供应商设备封装:D2PAK-3 包装:管件 |
| LT1121IS8#PBF | 功能描述:IC REG LDO ADJ .15A 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:8V 输入电压:10.5 V ~ 23 V 电压 - 压降（标准）:1.7V @ 40mA 稳压器数量:1 电流 - 输出:100mA（最小值） 电流 - 限制（最小）:- 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:剪切带 (CT) 产品目录页面:1075 (CN2011-ZH PDF) 其它名称:296-24390-1 |
| LT1121IS8#PBF | 制造商:Linear Technology 功能描述:Linear Voltage Regulator IC |
| LT1121IS8#TR | 功能描述:IC REG LDO ADJ .15A 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 产品培训模块:More Information on LDOs 标准包装:50 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.3V 输入电压:最高 15V 电压 - 压降（标准）:1.1V @ 800mA 稳压器数量:1 电流 - 输出:800mA 电流 - 限制（最小）:800mA 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-263-4，D²Pak（3 引线+接片），TO-263AA 供应商设备封装:D2PAK-3 包装:管件 |
| LT1121IS8#TRPBF | 功能描述:IC REG LDO ADJ .15A 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 产品培训模块:More Information on LDOs 标准包装:50 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.3V 输入电压:最高 15V 电压 - 压降（标准）:1.1V @ 800mA 稳压器数量:1 电流 - 输出:800mA 电流 - 限制（最小）:800mA 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-263-4，D²Pak（3 引线+接片），TO-263AA 供应商设备封装:D2PAK-3 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。