- 您现在的位置：买卖IC网 > PDF目录22296 > LT1123CZ#TRPBF (Linear Technology)IC REG CTRLR SGL 5V TO-92-3 PDF资料下载
参数资料
| 型号： | LT1123CZ#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 8/16页 |
| 文件大小： | 161K |
| 描述： | IC REG CTRLR SGL 5V TO-92-3 |
| 标准包装： | 2,000 |
| 类型： | 正，固定式 |
| 输出数： | 1 |
| 输出电压： | 5V |
| 电流 - 电源： | 700µA |
| 工作温度： | 0°C ~ 125°C |
| 封装/外壳： | TO-226-3、TO-92-3（TO-226AA）成形引线 |
| 供应商设备封装： | TO-92-3 |
| 包装： | 带卷 (TR) |
8
LT1123
1123fb
The curve in Figure 6 can be used to determine the range
of current limit of an LT1123 regulator circuit using an
MJE1123 as a pass transistor. The curve was generated
using the Beta versus I
C
curve of the MJE1123. The
minimum and maximum value curves are extrapolated
from the minimum and maximum Beta specifications.
Thermal Conditions
The thermal characteristics of three components need to
be considered; the LT1123, the pass transistor and R
D
.
Power dissipation should be calculated based on the
worst-case conditions seen by each component during
normal operation.
The worst-case power dissipation in the LT1123 is a
function of drive current, supply voltage and the value of
R
D
. Worst-case dissipation for the LT1123 occurs when
the drive current is equal to approximately one half of its
maximum value. Figure 7 plots the worst-case power
dissipation in the LT1123 versus R
D
and V
IN
. The graph
was generated using the following formula:
P
V V
4R
;R 10
D
IN BE
2
D
D
=
(
)
> &
where:
V
BE
= the emitter/base voltage of the PNP pass
transistor (assumed to be 0.6V)
For some operating conditions R
D
may be replaced with a
short. This is possible in applications where the operating
requirements (input voltage and drive current) are at the
low end and the output will not be shorted. For R
D
= 0 the
following formula may be used to calculate the maximum
power dissipation in the LT1123.
P
D
= (V
IN
V
BE
)(I
DRIVE
)
where:
V
IN
= maximum input voltage
V
BE
= emitter/base voltage of PNP
I
DRIVE
= required maximum drive current
The maximum junction temperature rise above ambient
for the LT1123 will be equal to the worst-case power
dissipation multiplied by the thermal resistance of the
device. The thermal resistance of the device will depend
upon how the device is mounted, and whether a heat sink
is used. Measurements show that one of the most effective
ways of heat sinking the TO-92 package is by utilizing the
PC board traces attached to the leads of the package. The
table below lists several methods of mounting and the
measured value of thermal resistance for each method. All
measurements were done in still air.
Package alone ............................................................................. 220癈/W
Package soldered into PC board with plated through
holes only ................................................................................175癈/W
Package soldered into PC board with 1/4 sq. in. of copper trace
per lead ....................................................................................145癈/W
Package soldered into PC board with plated through holes in
board, no extra copper trace, and a clip-on type heat sink:
Thermalloy type 2224B .................................................... 160癈/W
Aavid type 5754 ................................................................ 135癈/W
The maximum operating junction temperature of the
LT1123 is 125癈. The maximum operating ambient tem-
perature will be equal to 125癈 minus the maximum
junction temperature rise above ambient.
The worst-case power dissipation in R
D
needs to be
calculated so that the power rating of the resistor can be
determined. The worst-case power in the resistor will
occur when the drive current is at a maximum. Figure 8
plots the required power rating of R
D
versus supply
Figure 7. Power in LT1123
V
IN
(V)
6
8
1k
LT1123 F07
10
100
7
15
14
13
12
11
10
9
5
0.4W
0.7W
0.1W
0.2W
0.3W
0.5W
THERMAL
RESISTANCE
APPLICATIO S I FOR ATIO
U
U
U
相关PDF资料 |
PDF描述 |
|---|---|
| ACC30DRAN-S734 | CONN EDGECARD 60POS .100 R/A PCB |
| LT1123CZ#TR | IC REG CTRLR SGL 5V TO-92-3 |
| AISC-0402-8N2G-T | INDUCTOR CHIP 8.2NH 2% SMD |
| ACC30DRAH-S734 | CONN EDGECARD 60POS .100 R/A PCB |
| MIC5156YM TR | IC REG CTRLR SGL POS ADJ 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1124 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual/Quad Low Noise, High Speed Precision Op Amps |
| LT1124AC | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual/Quad Low Noise, High Speed Precision Op Amps |
| LT1124ACN8 | 功能描述:IC OP-AMP LOW NOISE DUAL 8-DIP RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:73 系列:Over-The-Top® 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.07 V/µs 增益带宽积:200kHz -3db带宽:- 电流 - 输入偏压:1nA 电压 - 输入偏移:285µV 电流 - 电源:50µA 电流 - 输出 / 通道:25mA 电压 - 电源，单路/双路(±):2 V ~ 44 V，±1 V ~ 22 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-WFDFN 裸露焊盘 供应商设备封装:16-DFN-EP（5x3） 包装:管件 |
| LT1124ACN8#PBF | 功能描述:IC OP-AMP LOW NOISE DUAL 8-DIP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:73 系列:Over-The-Top® 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.07 V/µs 增益带宽积:200kHz -3db带宽:- 电流 - 输入偏压:1nA 电压 - 输入偏移:285µV 电流 - 电源:50µA 电流 - 输出 / 通道:25mA 电压 - 电源，单路/双路(±):2 V ~ 44 V，±1 V ~ 22 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-WFDFN 裸露焊盘 供应商设备封装:16-DFN-EP（5x3） 包装:管件 |
| LT1124AI | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual/Quad Low Noise, High Speed Precision Op Amps |
发布紧急采购，3分钟左右您将得到回复。