- 您现在的位置：买卖IC网 > PDF目录4677 > LT1129CS8-3.3#TRPBF (Linear Technology)IC REG LDO 3.3V .7A 8-SOIC PDF资料下载
参数资料
| 型号： | LT1129CS8-3.3#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 10/16页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 3.3V .7A 8-SOIC |
| 产品培训模块： | More Information on LDOs |
| 标准包装： | 2,500 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 3.3V |
| 输入电压： | 4.15 V ~ 30 V |
| 电压 - 压降（标准）： | 0.45V @ 700mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 700mA |
| 工作温度： | 0°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 带卷 (TR) |
LT1129/LT1129-3.3/LT1129-5
APPLICATIONS INFORMATION
? ( ) = ( )
Adjustable Operation
The adjustable version of the LT1129 has an output voltage
range of 3.75V to 30V. The output voltage is set by the
ratio of two external resistors as shown in Figure 2. The
device servos the output voltage to maintain the voltage
at the adjust pin at 3.75V. The current in R1 is then equal
to 3.75V/R1. The current in R2 is equal to the sum of the
current in R1 and the adjust pin bias current. The adjust
pin bias current, 150nA at 25°C, ?ows through R2 into the
adjust pin. The output voltage can be calculated according
to the formula in Figure 2. The value of R1 should be less
than 400k to minimize errors in the output voltage caused
by the adjust pin bias current. Note that in shutdown the
output is turned off and the divider current will be zero.
Curves of Adjust Pin Voltage vs Temperature and Adjust
Pin Bias Current vs Temperature appear in the Typical
Performance Characteristics. The reference voltage at
the adjust pin has a positive temperature coef?cient of
approximately 15ppm/°C. The adjust pin bias current has
a negative temperature coef?cient. These effects are small
and will tend to cancel each other.
The adjustable device is speci?ed with the adjust pin tied
to the output pin. This sets the output voltage to 3.75V.
Speci?cations for output voltages greater than 3.75V will
be proportional to the ratio of the desired output voltage
to 3.75V (V OUT /3.75V). For example: load regulation for an
output current change of 1mA to 700mA is – 6mV typical at
V OUT = 3.75V. At V OUT = 12V, load regulation would be:
12V
–6mV –19mV
3.75V
Thermal Considerations
The power handling capability of the device will be limited
by the maximum rated junction temperature (125°C). The
power dissipated by the device will be made up of two
components:
1. Output current multiplied by the input/output voltage
differential: I OUT ? (V IN – V OUT ), and
2. Ground pin current multiplied by the input voltage:
I GND ? V IN .
The ground pin current can be found by examining the
Ground Pin Current curves in the Typical Performance
Characteristics. Power dissipation will be equal to the
sum of the two components listed above.
The LT1129 series regulators have internal thermal
limiting designed to protect the device during overload
conditions. For continuous normal load conditions the
maximum junction temperature rating of 125°C must not
be exceeded. It is important to give careful consideration
to all sources of thermal resistance from junction to ambi-
ent. Additional heat sources mounted nearby must also be
considered.
For surface mount devices heat sinking is accomplished
by using the heat spreading capabilities of the PC board
and its copper traces. Experiments have shown that the
heat spreading copper layer does not need to be electri-
cally connected to the tab of the device. The PC material
can be very effective at transmitting heat between the pad
area, attached to the tab of the device, and a ground or
power plane layer either inside or on the opposite side of
the board. Although the actual thermal resistance of the
PC material is high, the length/area ratio of the thermal
IN
OUT
V OUT
resistor between layers is small. Copper board stiffeners
LT1129
SHDN
GND
ADJ
R2
R1
+
and plated through holes can also be used to spread the
heat generated by power devices.
The following tables list thermal resistances for each
package. For the TO-220 package, thermal resistance
( )
(
)
V OUT = 3.75V 1 + + I ADJ ? R2
112935 F02
R2
R1
V ADJ = 3.75V
I ADJ = 150nA at 25°C
OUTPUT RANGE = 3.75V to 30V
Figure 2. Adjustable Operation
is given for junction-to-case only since this package
is usually mounted to a heat sink. Measured values of
thermal resistance for several different board sizes and
copper areas are listed for each package. All measure-
ments were taken in still air on 3/32" FR-4 board with 1-oz
112935ff
10
相关PDF资料 |
PDF描述 |
|---|---|
| LT1129CS8-3.3#TR | IC REG LDO 3.3V .7A 8SOIC |
| GSM36DSEI | CONN EDGECARD 72POS .156 EYELET |
| ACC40DREF | CONN EDGECARD 80POS .100 EYELET |
| ACM18DSAN | CONN EDGECARD 36POS R/A .156 SLD |
| LT1965EQ-1.5#PBF | IC REG LDO 1.5V 1.1A 5-DDPAK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1129CS8-5 | 功能描述:IC REG LDO 5V .7A 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:800 系列:- 稳压器拓扑结构:正，固定式 输出电压:2.5V 输入电压:最高 16V 电压 - 压降（标准）:0.7V @ 4A 稳压器数量:1 电流 - 输出:4A 电流 - 限制（最小）:4.2A 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-263-6，D²Pak（5 引线+接片），TO-263BA 供应商设备封装:TO-263-5 包装:带卷 (TR) 其它名称:AP1184K525L-13AP1184K525LDITR |
| LT1129CS8-5#PBF | 功能描述:IC REG LDO 5V .7A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:8V 输入电压:10.5 V ~ 23 V 电压 - 压降（标准）:1.7V @ 40mA 稳压器数量:1 电流 - 输出:100mA（最小值） 电流 - 限制（最小）:- 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:剪切带 (CT) 产品目录页面:1075 (CN2011-ZH PDF) 其它名称:296-24390-1 |
| LT1129CS8-5#TR | 功能描述:IC REG LDO 5V .7A 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:800 系列:- 稳压器拓扑结构:正，固定式 输出电压:2.5V 输入电压:最高 16V 电压 - 压降（标准）:0.7V @ 4A 稳压器数量:1 电流 - 输出:4A 电流 - 限制（最小）:4.2A 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-263-6，D²Pak（5 引线+接片），TO-263BA 供应商设备封装:TO-263-5 包装:带卷 (TR) 其它名称:AP1184K525L-13AP1184K525LDITR |
| LT1129CS8-5#TRPBF | 功能描述:IC REG LDO 5V .7A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:800 系列:- 稳压器拓扑结构:正，固定式 输出电压:2.5V 输入电压:最高 16V 电压 - 压降（标准）:0.7V @ 4A 稳压器数量:1 电流 - 输出:4A 电流 - 限制（最小）:4.2A 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-263-6，D²Pak（5 引线+接片），TO-263BA 供应商设备封装:TO-263-5 包装:带卷 (TR) 其它名称:AP1184K525L-13AP1184K525LDITR |
| LT1129CS8-5PBF | 制造商:Linear Technology 功能描述:LDO Regulator Positive 5V 0.7A SOIC8 |
发布紧急采购，3分钟左右您将得到回复。