参数资料
| 型号： | LT1129IS8#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 12/16页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO ADJ .7A 8-SOIC |
| 产品培训模块： | More Information on LDOs |
| 标准包装： | 100 |
| 稳压器拓扑结构： | 正，可调式 |
| 输出电压： | 3.8 V ~ 30 V |
| 输入电压： | 4.15 V ~ 30 V |
| 电压 - 压降（标准）： | 0.45V @ 700mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 700mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 管件 |
| 产品目录页面： | 1326 (CN2011-ZH PDF) |
LT1129/LT1129-3.3/LT1129-5
APPLICATIONS INFORMATION
Current limit protection and thermal overload protection
are intended to protect the device against current overload
conditions at the output of the device. For normal operation,
the junction temperature should not exceed 125°C.
The input of the device will withstand reverse voltages
of 30V. Current ?ow into the device will be limited to less
than 1mA (typically less than 100μA) and no negative
voltage will appear at the output. The device will protect
both itself and the load. This provides protection against
batteries that can be plugged in backwards.
For ?xed voltage versions of the device, the sense pin
is internally clamped to one diode drop below ground.
For the adjustable version of the device, the output pin
is internally clamped at one diode drop below ground. If
the output pin of an adjustable device, or the sense pin
of a ?xed voltage device, is pulled below ground, with the
input open or grounded, current must be limited to less
than 5mA.
In circuits where a backup battery is required, several
different input /output conditions can occur. The output
voltage may be held up while the input is either pulled
to ground, pulled to some intermediate voltage, or is left
open circuit. Current ?ow back into the output will vary
depending on the conditions. Many battery-powered
circuits incorporate some form of power management.
The following information will help optimize battery life.
Table 4 summarizes the following information.
100
The reverse output current will follow the curve in Figure 3
when the input pin is pulled to ground. This current ?ows
through the output pin to ground. The state of the shutdown
pin will have no effect on output current when the input
pin is pulled to ground.
In some applications it may be necessary to leave the
input to the LT1129 unconnected when the output is held
high. This can happen when the LT1129 is powered from
a recti?ed AC source. If the AC source is removed, then
the input of the LT1129 is effectively left ?oating. The
reverse output current also follows the curve in Figure 3
if the input pin is left open. The state of the shutdown pin
will have no effect on the reverse output current when the
input pin is ?oating.
When the input of the LT1129 is forced to a voltage below
its nominal output voltage and its output is held high, the
reverse output current will still follow the curve shown
in Figure 3. This can happen if the input of the LT1129 is
connected to a discharged (low voltage) battery and the
output is held up by either a backup battery or by a second
regulator circuit.
When the input pin is forced below the output pin or the
output pin is pulled above the input pin, the input current will
typically drop to less than 2μA (see Figure 4). The state of
the shutdown pin will have no effect on the reverse output
current when the output is pulled above the input.
5
V SENSE = V OUT
T J = 25°C
90 V IN = 0V
80
CURRENT FLOWS
70 INTO DEVICE
4
V OUT = 3.3V (LT1129-3.3)
V OUT = 5V (LT1129-5)
60
50
LT1129
3
40
30
20
10
LT1129-3.3
LT1129-5
2
1
0
0
1
2
3
4
5
6
7
8
9
10
0
0
1
2
3
4
5
OUTPUT VOLTAGE (V)
112935 F03
Figure 3. Reverse Output Current
INPUT VOLTAGE (V)
112935 F04
Figure 4. Input Current
112935ff
12
相关PDF资料 |
PDF描述 |
|---|---|
| 1782-89J | COIL RF 750UH MOLDED UNSHIELDED |
| 420USC330MEFCSN25X50 | CAP ALUM 330UF 420V 20% SNAP-IN |
| 2510-52K | INDUCTOR 15UH SMT 10% TOL |
| 400MXH270MEFCSN30X25 | CAP ALUM 270UF 400V 20% SNAP-IN |
| EMM15DKLH | CONN EDGECARD 30POS .156 WW |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1129IST-3.3 | 功能描述:IC REG LDO 3.3V .7A SOT223-3 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:800 系列:- 稳压器拓扑结构:正，固定式 输出电压:2.5V 输入电压:最高 16V 电压 - 压降（标准）:0.7V @ 4A 稳压器数量:1 电流 - 输出:4A 电流 - 限制（最小）:4.2A 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-263-6，D²Pak（5 引线+接片），TO-263BA 供应商设备封装:TO-263-5 包装:带卷 (TR) 其它名称:AP1184K525L-13AP1184K525LDITR |
| LT1129IST-3.3#PBF | 功能描述:IC REG LDO 3.3V .7A SOT223-3 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:8V 输入电压:10.5 V ~ 23 V 电压 - 压降（标准）:1.7V @ 40mA 稳压器数量:1 电流 - 输出:100mA（最小值） 电流 - 限制（最小）:- 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:剪切带 (CT) 产品目录页面:1075 (CN2011-ZH PDF) 其它名称:296-24390-1 |
| LT1129IST-3.3#PBF | 制造商:Linear Technology 功能描述:Linear Voltage Regulator IC |
| LT1129IST-3.3#TR | 功能描述:IC REG LDO 3.3V .7A SOT223-3 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:800 系列:- 稳压器拓扑结构:正，固定式 输出电压:2.5V 输入电压:最高 16V 电压 - 压降（标准）:0.7V @ 4A 稳压器数量:1 电流 - 输出:4A 电流 - 限制（最小）:4.2A 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-263-6，D²Pak（5 引线+接片），TO-263BA 供应商设备封装:TO-263-5 包装:带卷 (TR) 其它名称:AP1184K525L-13AP1184K525LDITR |
| LT1129IST-3.3#TRPBF | 功能描述:IC REG LDO 3.3V .7A SOT223-3 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:800 系列:- 稳压器拓扑结构:正，固定式 输出电压:2.5V 输入电压:最高 16V 电压 - 压降（标准）:0.7V @ 4A 稳压器数量:1 电流 - 输出:4A 电流 - 限制（最小）:4.2A 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-263-6，D²Pak（5 引线+接片），TO-263BA 供应商设备封装:TO-263-5 包装:带卷 (TR) 其它名称:AP1184K525L-13AP1184K525LDITR |
发布紧急采购，3分钟左右您将得到回复。