- 您现在的位置：买卖IC网 > PDF目录14073 > LT1173CS8#TR (Linear Technology)IC REG BUCK BOOST INV ADJ 8SOIC PDF资料下载
参数资料
| 型号： | LT1173CS8#TR |
| 厂商： | Linear Technology |
| 文件页数： | 6/16页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK BOOST INV ADJ 8SOIC |
| 标准包装： | 2,500 |
| 类型： | 降压（降压），升压（升压），反相 |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.25 V ~ 50 V |
| 输入电压： | 2 V ~ 30 V |
| 频率 - 开关： | 23kHz |
| 电流 - 输出： | 400mA |
| 同步整流器： | 无 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 8-SOIC |
LT1173
A PPLICATI
S I FOR ATIO
+12V
1M ?
the inductive events add to the input voltage to produce the
output voltage. Power required from the inductor is deter-
–
LTC1050
1 μ F*
100 ?
V1
V2
LT1173
CIRCUIT
mined by
P L = (V OUT + V D – V IN ) (I OUT )
(02)
+
1000 μ F
+
where V D is the diode drop (0.5V for a 1N5818 Schottky).
Energy required by the inductor per cycle must be equal or
V SET
*NON-POLARIZED
LT1173 ? TA06
greater than
Figure 1. Test Circuit Measures No Load Quiescent Current of
LT1073 Converter
P L
F OSC
( 03 )
Inductor Selection
A DC-DC converter operates by storing energy as mag-
netic flux in an inductor core, and then switching this
in order for the converter to regulate the output.
When the switch is closed, current in the inductor builds
according to
()
I L t = IN ? 1 – e L ?
( )
energy into the load. Since it is flux, not charge, that is
stored, the output voltage can be higher, lower, or oppo-
site in polarity to the input voltage by choosing an
appropriate switching topology. To operate as an efficient
V ? –R't ?
R ' ? ?
04
energy transfer element, the inductor must fulfill three
requirements. First, the inductance must be low enough
for the inductor to store adequate energy under the worst
case condition of minimum input voltage and switch ON
where R' is the sum of the switch equivalent resistance
(0.8 ? typical at 25 ° C) and the inductor DC resistance.
When the drop across the switch is small compared to V IN ,
the simple lossless equation
()
I L t = IN t
( )
time. The inductance must also be high enough so that
maximum current ratings of the LT1173 and inductor are
not exceeded at the other worst case condition of maxi-
V
L
05
( 06 )
E L =
1 2
2 PEAK
mum input voltage and ON time. Additionally, the inductor
core must be able to store the required flux; i.e., it must not
saturate. At power levels generally encountered with
LT1173 based designs, small axial leaded units with
saturation current ratings in the 300mA to 1A range
(depending on application) are adequate. Lastly, the in-
ductor must have sufficiently low DC resistance so that
excessive power is not lost as heat in the windings. An
additional consideration is Electro-Magnetic Interference
(EMI). Toroid and pot core type inductors are recom-
mended in applications where EMI must be kept to a
minimum; for example, where there are sensitive analog
circuitry or transducers nearby. Rod core types are a less
expensive choice where EMI is not a problem.
Specifying a proper inductor for an application requires
first establishing minimum and maximum input voltage,
output voltage, and output current. In a step-up converter,
6
can be used. These equations assume that at t = 0,
inductor current is zero. This situation is called “discon-
tinuous mode operation” in switching regulator parlance.
Setting “t” to the switch ON time from the LT1173 speci-
fication table (typically 23 μ s) will yield i PEAK for a specific
“L” and V IN . Once i PEAK is known, energy in the inductor at
the end of the switch ON time can be calculated as
Li
E L must be greater than P L /F OSC for the converter to deliver
the required power. For best efficiency i PEAK should be
kept to 1A or less. Higher switch currents will cause
excessive drop across the switch resulting in reduced
efficiency. In general, switch current should be held to as
low a value as possible in order to keep switch, diode and
inductor losses at a minimum.
相关PDF资料 |
PDF描述 |
|---|---|
| LT1111CS8-5#TRPBF | IC REG BUCK BST INV 5V .4A 8SOIC |
| LT1111CS8-5#TR | IC REG BUCK BST INV 5V .4A 8SOIC |
| MAX6869UK22D2L+T | IC MPU SUPERVISOR SOT23-5 |
| MAX6869UK23D1S+T | IC MPU SUPERVISOR SOT23-5 |
| MAX6869UK22D6S+T | IC MPU SUPERVISOR SOT23-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT11743 | 制造商:LINEAR 制造商全称:LINEAR 功能描述:High Efficiency Step-Down Switching Regulator Controllers |
| LT1175 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Micropower Low Dropout Regulators with Shutdown |
| LT1175_05 | 制造商:LINER 制造商全称:Linear Technology 功能描述:500mA Negative Low Dropout Micropower Regulator |
| LT1175_10 | 制造商:LINER 制造商全称:Linear Technology 功能描述:500mA Negative Low Dropout Micropower Regulator |
| LT1175-5 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Precision Micropower RMS-to-DC Converter |
发布紧急采购，3分钟左右您将得到回复。