- 您现在的位置：买卖IC网 > PDF目录13937 > LT1176CSW (Linear Technology)IC REG MULTI CONFIG ADJ 20SOIC PDF资料下载
参数资料
| 型号： | LT1176CSW |
| 厂商： | Linear Technology |
| 文件页数： | 4/8页 |
| 文件大小： | 0K |
| 描述： | IC REG MULTI CONFIG ADJ 20SOIC |
| 标准包装： | 38 |
| 类型： | 降压（降压），反相，回扫 |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 2.2 V ~ 29.8 V |
| 输入电压： | 8 V ~ 35 V |
| 频率 - 开关： | 100kHz |
| 电流 - 输出： | 1A |
| 同步整流器： | 无 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SOIC（0.295"，7.50mm 宽） |
| 包装： | 管件 |
| 供应商设备封装： | 20-SOIC |
| 其它名称： | LT1176CS |
LT1176/LT1176-5
ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications ar e at T A = 25°C. T J = 25°C, V IN 25V, unless otherwise noted.
PARAMETER
Status Low Level
CONDITIONS
I STATUS = 1.6mA Sinking
l
MIN
TYP
0.25
MAX
0.4
UNITS
V
Status Delay Time
Status Minimum Width
9
30
μs
μs
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: To calculate maximum switch ON voltage at current between low
and high conditions, a linear interpolation may be used.
Note 3: A feedback pin voltage (V FB ) of 2.5V forces the V C pin to its low
clamp level and the switch duty cycle to zero. This approximates the
zero load condition where duty cycle approaches zero. The LT1176-5 has
V SENSE = 5.5V.
Note 4: Total voltage from V IN pin to ground pin must be ≥ 8V after
start-up for proper regulation.
Application Hints
Although the LT1176 has a peak switch rating of 1.2A and a maximum duty
cycle of 85%, it must be used cautiously in applications which require high
switch current and high duty cycle simultaneously, to avoid excessive chip
temperature. Thermal resistance is 90°C/W for the 8-pin DIP package and
50°C/W for the 20-pin SO. This limits continuous chip power dissipation to
the 0.5W to 1W range. These numbers assume typical mounting techniques.
Extra or thick copper connected to the leads can reduce thermal resistance.
Bonding the package to the board or using a clip style heat sink can also help.
The following formulas will give chip power dissipation and peak switch current
for the standard buck converter. Note that surges less than 30 seconds do not
need to be considered from a thermal standpoint, but for proper regulation,
they must not result in peak switch currents exceeding the 1.2A limit.
Note 5: Switch frequency is internally scaled down when the feedback pin
voltage is less than 1.3V to avoid extremely short switch-on times. During
testing, V FB or V SENSE is adjusted to give a minimum switch-on time of
1μs.
Note 6: I LM = (R LIM – 1k)/7.65k
Note 7: Switch to input voltage limitation must also be observed.
Note 8: V MAX = 35V
Note 9: Does not include switch leakage.
Note 10: Error amplifier voltage gain and transconductance are
specified relative to the internal feedback node. To calculate gain and
transconductance from the sense pin (Output) to the V C pin on the
LT1176-5, multiply by 0.44.
Power = I LOAD (V OUT /V IN ) + V IN [7mA + 3mA (V OUT /V IN ) + 0.012 (I LOAD )]
I PEAK = I LOAD(PEAK) + [V OUT (V IN – V OUT )]/2E 5 (V IN )(L)
Example: V IN = 15V, V OUT = 5V, I LOAD = 0.5A Continuous, 0.8A Peak,
L = 100μH
Power (I LOAD = 0.5A) = 0.38W
I PEAK (I LOAD = 0.8A) = 0.97A
Where component size or height is critical, we suggest using solid tantalum
capacitors (singly or in parallel), but be sure to use units rated for switching
applications. Coiltronics is a good source for low profile surface mount
inductors and AVX makes high quality surface mount tantalum capacitors. For
further help, use Application Notes 19 and 44,LTC’s SwitcherCAD ? computer
design program, and our knowledgeable application department.
11765fb
4
相关PDF资料 |
PDF描述 |
|---|---|
| V150B5E200BF | CONVERTER MOD DC/DC 5V 200W |
| LT1176CSW-5 | IC REG BUCK INV FLYBACK 20SOIC |
| V150B5E200BL3 | CONVERTER MOD DC/DC 5V 200W |
| LTC3417AIFE-1#PBF | IC REG BUCK SYNC ADJ DL 20TSSOP |
| V150B5E200BL | CONVERTER MOD DC/DC 5V 200W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1176CSW#PBF | 功能描述:IC REG MULTI CONFIG ADJ 20SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:MIC23xxx HyperLight Load™ Regulators 标准包装:5,000 系列:HyperLight Load® 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.8V 输入电压:2.7 V ~ 5.5 V PWM 型:混合物 频率 - 开关:4MHz 电流 - 输出:2A 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘，8-MLF? 包装:带卷 (TR) 供应商设备封装:8-MLF?（2x2） 产品目录页面:1094 (CN2011-ZH PDF) 其它名称:576-3303-2 |
| LT1176CSW#TR | 功能描述:IC REG MULTI CONFIG ADJ 20SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1176CSW#TRPBF | 功能描述:IC REG MULTI CONFIG ADJ 20SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1176CSW-5 | 功能描述:IC REG BUCK INV FLYBACK 20SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1176CSW-5#PBF | 功能描述:IC REG BUCK INV FLYBACK 20SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
发布紧急采购，3分钟左右您将得到回复。