参数资料
| 型号： | LT1182IS#TR |
| 厂商： | Linear Technology |
| 文件页数： | 16/24页 |
| 文件大小： | 0K |
| 描述： | IC REG SW DUAL CCFL/LCD 16SOIC |
| 标准包装： | 2,500 |
| 应用： | 转换器，CCFL，LCD |
| 输入电压： | 3 V ~ 30 V |
| 输出数： | 1 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SOIC |
| 包装： | 带卷 (TR) |
LT1182/LT1183/LT1184/LT1184F
APPLICATIO N S I N FOR M ATIO N
change in quiescent current. An active low shutdown pin
typically reduces total supply current to 35 μ A by shutting
off the 2.4V regulator and locking out switching action for
standby operation. The ICs incorporate undervoltage lock-
out by sensing regulator dropout and locking out switch-
ing below about 2.5V. The regulators also provide thermal
shutdown protection that locks out switching in the pres-
ence of excessive junction temperatures.
A 200kHz oscillator is the basic clock for all internal timing.
The oscillator turns on an output via its own logic and
driver circuitry. Adaptive anti-sat circuitry detects the
onset of saturation in a power switch and adjusts base
drive current instantaneously to limit switch saturation.
This minimizes driver dissipation and provides rapid turn-
off of the switch. The CCFL power switch is guaranteed to
provide a minimum of 1.25A in the LT1182/LT1183/
LT1184/LT1184F and the LCD power switch is guaranteed
to provide a minimum of 0.625A in the LT1182/LT1183.
The anti-sat circuitry provides a ratio of switch current to
driver current of about 50:1.
Simplified Lamp Current Programming
A programming block in the LT1182/LT1183/LT1184/
LT1184F controls lamp current, permitting either grounded-
lamp or floating-lamp configurations. Grounded configu-
rations control lamp current by directly controlling one-
half of actual lamp current and converting it to a feedback
signal to close a control loop. Floating configurations
control lamp current by directly controlling the Royer’s
primary side converter current and generating a feedback
signal to close a control loop.
Previous backlighting solutions have used a traditional
error amplifier in the control loop to regulate lamp current.
This approach converted an RMS current into a DC voltage
for the input of the error amplifier. This approach used
several time constants in order to provide stable loop
frequency compensation. This compensation scheme
meant that the loop had to be fairly slow and that output
overshoot with startup or overload conditions had to be
carefully evaluated in terms of transformer stress and
breakdown voltage requirements.
The LT1182/LT1183/LT1184/LT1184F eliminate the error
amplifier concept entirely and replace it with a lamp
16
current programming block. This block provides an easy-
to-use interface to program lamp current. The program-
mer circuit also reduces the number of time constants in
the control loop by combining the error signal conversion
scheme and frequency compensation into a single capaci-
tor. The control loop thus exhibits the response of a single
pole system, allows for faster loop transient response and
virtually eliminates overshoot under startup or overload
conditions.
Lamp current is programmed at the input of the program-
mer block, the I CCFL pin. This pin is the input of a shunt
regulator and accepts a DC input current signal of 0 μ A to
100 μ A. This input signal is converted to a 0 μ A to 500uA
source current at the CCFL V C pin. The programmer circuit
is simply a current-to-current converter with a gain of five.
By regulating the I CCFL pin, the input programming current
can be set with DAC, PWM or potentiometer control. The
typical input current programming range for 0mA to 6mA
lamp current is 0 μ A to 50 μ A.
The I CCFL pin is sensitive to capacitive loading and will
oscillate with capacitance greater than 10pF. For example,
loading the I CCFL pin with a 1 × or 10 × scope probe causes
oscillation and erratic CCFL regulator operation because
of the probe’s respective input capacitance. A current
meter in series with the I CCFL pin will also produce oscil-
lation due to its shunt capacitance. Use a decoupling
resistor of several kilo-ohms between the I CCFL pin and the
control circuitry if excessive stray capacitance exists. This
is basically free with potentiometer or PWM control as
these control schemes use resistors. A current output
DAC should use an isolating resistor as the DAC can have
significant output capacitance that changes as a function
of input code.
Grounded-Lamp Configuration
In a grounded-lamp configuration, the low voltage side of
the lamp connects directly to the LT1182/LT1183/LT1184/
LT1184F DIO pin. This pin is the common connection
between the cathode and anode of two internal diodes. In
previous grounded-lamp solutions, these diodes were
discrete units and are now integrated onto the IC, saving
cost and board space. Bi-directional lamp current flows in
the DIO pin and thus, the diodes conduct alternately on half
相关PDF资料 |
PDF描述 |
|---|---|
| EMM30DTKS | CONN EDGECARD 60POS DIP .156 SLD |
| HBM36DSEN-S243 | CONN EDGECARD 72POS .156 EYELET |
| LT1580CR-2.5#TR | IC REGULATOR LDO 2.5V 7A DDPAK-7 |
| LT3011EDD#PBF | IC REG LDO ADJ 50MA 10-DFN |
| 1210-273J | INDUCTOR FERRITE CORE 27UH SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1183CS | 功能描述:IC SW REG CCFL/LCD CONTRST16SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:2,000 系列:- 应用:控制器，DSP 输入电压:4.5 V ~ 25 V 输出数:2 输出电压:最低可调至 1.2V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:30-TFSOP（0.173"，4.40mm 宽） 供应商设备封装:30-TSSOP 包装:带卷 (TR) |
| LT1183CS#PBF | 功能描述:IC SW REG CCFL/LCD CONTRST16SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:2,000 系列:- 应用:控制器，DSP 输入电压:4.5 V ~ 25 V 输出数:2 输出电压:最低可调至 1.2V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:30-TFSOP（0.173"，4.40mm 宽） 供应商设备封装:30-TSSOP 包装:带卷 (TR) |
| LT1183CS#TR | 功能描述:IC REG SW DUAL CCFL/LCD 16SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| LT1183CS#TRPBF | 功能描述:IC SW REG CCFL/LCD CONTRST16SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| LT1184CS | 功能描述:IC SW REG CCFL CONTRAST 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。