- 您现在的位置：买卖IC网 > PDF目录377691 > LT1184FCS (LINEAR TECHNOLOGY CORP) RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS PDF资料下载
参数资料
| 型号： | LT1184FCS |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| 中文描述： | 1.25 A FLUORESCENT LIGHT CONTROLLER, 200 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封装： | PLASTIC, SO-16 |
| 文件页数： | 10/24页 |
| 文件大小： | 409K |
| 代理商： | LT1184FCS |
10
LT1182/LT1183/LT1184/LT1184F
LT1182/LT1183/LT1184/LT1184F
CCFL PGND (Pin 1):
This pin is the emitter of an internal
NPN power switch. CCFL switch current flows through
this pin and permits internal, switch-current sensing. The
regulators provide a separate analog ground and power
ground(s) to isolate high current ground paths from low
current signal paths. Linear Technology recommends the
use of star-ground layout techniques.
I
CCFL
(Pin 2):
This pin is the input to the CCFL lamp current
programming circuit. This pin internally regulates to 450mV
(LT1182/LT1183) or 465mV (LT1184/LT1184F). The pin
accepts a DC input current signal of 0
μ
A to 100
μ
A full
scale. This input signal is converted to a 0
μ
A to 500
μ
A
source current at the CCFL V
C
pin. By shunt regulating the
I
CCFL
pin, the input programming current can be set with
DAC, PWM or potentiometer control. As input program-
ming current increases, the regulated lamp current in-
creases. For a typical 6mA lamp, the range of input
programming current is about 0
μ
A to 50
μ
A.
DIO (Pin 3):
This pin is the common connection between
the cathode and anode of two internal diodes. The remain-
ing terminals of the two diodes connect to ground. In a
grounded lamp configuration, DIO connects to the low
voltage side of the lamp. Bidirectional lamp current flows
in the DIO pin and thus the diodes conduct alternately on
half cycles. Lamp current is controlled by monitoring one-
half of the average lamp current. The diode conducting on
negative half cycles has one-tenth of its current diverted to
the CCFL V
C
pin. This current nulls against the source
current provided by the lamp-current programmer circuit.
A single capacitor on the CCFL V
C
pin provides both stable
loop compensation and an averaging function to the half-
wave-rectified sinusoidal lamp current. Therefore, input
programming current relates to one-half of average lamp
current. This scheme reduces the number of loop com-
pensation components and permits faster loop transient
response in comparison to previously published circuits.
If a floating-lamp configuration is used, ground the DIO
pin.
CCFL V
C
(Pin 4):
This pin is the output of the lamp current
programmer circuit and the input of the current compara-
tor for the CCFL regulator. Its uses include frequency
compensation, lamp-current averaging for grounded lamp
circuits, and current limiting. The voltage on the CCFL V
C
pin determines the current trip level for switch turnoff.
During normal operation this pin sits at a voltage between
0.95V (zero switch current) and 2.0V (maximum switch
current) with respect to analog ground (AGND). This pin
has a high impedance output and permits external voltage
clamping to adjust current limit. A single capacitor to
ground provides stable loop compensation. This simpli-
fied loop compensation method permits the CCFL regula-
tor to exhibit single-pole transient response behavior and
virtually eliminates transformer output overshoot.
AGND (Pin 5):
This pin is the low current analog ground.
It is the negative sense terminal for the internal 1.24V
reference and the I
CCFL
summing voltage in the LT1182/
LT1183/LT1184/LT1184F. It is also a sense terminal for
the LCD dual input error amplifier in the LT1182/LT1183.
Connect external feedback divider networks that terminate
to ground and frequency compensation components that
terminate to ground directly to this pin for best regulation
and performance.
SHUTDOWN (Pin 6):
Pulling this pin low causes complete
regulator shutdown with quiescent current typically re-
duced to 35
μ
A. The nominal threshold voltage for this pin
is 0.85V. If the pin is not used, it can float high or be pulled
to a logic high level (maximum of 6V). Carefully evaluate
active operation when allowing the pin to float high.
Capacitive coupling into the pin from switching transients
could cause erratic operation.
CCFL V
SW
(Pin 16):
This pin is the collector of the internal
NPN power switch for the CCFL regulator. The power
switch provides a minimum of 1.25A. Maximum switch
current is a function of duty cycle as internal slope com-
pensation ensures stability with duty cycles greater than
50%. Using a driver loop to automatically adapt base drive
current to the minimum required to keep the switch in a
quasi-saturation state yields fast switching times and high
efficiency operation. The ratio of switch current to driver
current is about 50:1.
PI
FU
CTIO
N
S
U
U
相关PDF资料 |
PDF描述 |
|---|---|
| LT1183CS | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| LT1184CS | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| LT1182 | 500kHz and 1MHz High Efficiency 1.5A Switching Regulators; Package: SO; No of Pins: 8; Temperature Range: -40?°C to 85?°C |
| LT1183 | 500kHz and 1MHz High Efficiency 1.5A Switching Regulators; Package: SO; No of Pins: 8; Temperature Range: -40?°C to 85?°C |
| LT1184 | 500kHz and 1MHz High Efficiency 1.5A Switching Regulators; Package: SO; No of Pins: 8; Temperature Range: -40?°C to 85?°C |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1184FCS#PBF | 功能描述:IC SW REG CCFL CONTRAST 16-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:2,000 系列:- 应用:控制器，DSP 输入电压:4.5 V ~ 25 V 输出数:2 输出电压:最低可调至 1.2V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:30-TFSOP（0.173"，4.40mm 宽） 供应商设备封装:30-TSSOP 包装:带卷 (TR) |
| LT1184FCS#PBF | 制造商:Linear Technology 功能描述:DC-DC CONVERTER BUCK 200KHZ 制造商:Linear Technology 功能描述:DC-DC CONVERTER, BUCK, 200KHZ, 1A, SOIC- |
| LT1184FCS#TR | 功能描述:IC REG SWITCH DUAL CCFL 16SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| LT1184FCS#TRPBF | 功能描述:IC SW REG CCFL CONTRAST 16-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| LT1184FIS | 功能描述:IC SW REG CCFL CONTRAST 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。