参数资料
| 型号： | LT1226CS8#TR |
| 厂商： | Linear Technology |
| 文件页数： | 6/8页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP 1GHZ HI SPEED LN 8SOIC |
| 标准包装： | 2,500 |
| 放大器类型： | 通用 |
| 电路数： | 1 |
| 转换速率： | 400 V/µs |
| 增益带宽积： | 1GHz |
| 电流 - 输入偏压： | 4µA |
| 电压 - 输入偏移： | 300µV |
| 电流 - 电源： | 7mA |
| 电流 - 输出 / 通道： | 40mA |
| 电压 - 电源，单路/双路(±)： | ±2.5 V ~ 15 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SO |
| 包装： | 带卷 (TR) |
LT1226
6
U
S
A
O
PPLICATI
WU
U
I FOR ATIO
The LT1226 may be inserted directly into HA2541, HA2544,
AD847, EL2020 and LM6361 applications, provided that
the amplifier configuration is a noise gain of 25 or greater,
and the nulling circuitry is removed. The suggested nulling
circuit for the LT1226 is shown below.
Offset Nulling
Layout and Passive Components
As with any high speed operational amplifier, care must be
taken in board layout in order to obtain maximum perfor-
mance. Key layout issues include: use of a ground plane,
minimization of stray capacitance at the input pins, short
lead lengths, RF-quality bypass capacitors located close
to the device (typically 0.01
F to 0.1F), and use of low
ESR bypass capacitors for high drive current applications
(typically 1
F to 10F tantalum). Sockets should be
avoided when maximum frequency performance is
required, although low profile sockets can provide
reasonable performance up to 50MHz. For more details
see Design Note 50. Feedback resistors greater than 5k
are not recommended because a pole is formed with the
input capacitance which can cause peaking. If feedback
resistors greater than 5k
are used, a parallel
capacitor of 5pF to 10pF should be used to cancel the input
pole and optimize dynamic performance.
Transient Response
The LT1226 gain bandwidth is 1GHz when measured at
1MHz. The actual frequency response in a gain of +25 is
considerably higher than 40MHz due to peaking caused by
a second pole beyond the gain of 25 crossover point. This
is reflected in the small signal transient response. Higher
noise gain configurations exhibit less overshoot as seen in
the inverting gain of 25 response.
Small Signal, AV = +25
Small Signal, AV = – 25
The large signal response in both inverting and noninvert-
ing gain shows symmetrical slewing characteristics. Nor-
mally the noninverting response has a much faster rising
edge due to the rapid change in input common mode
voltage which affects the tail current of the input differen-
tial pair. Slew enhancement circuitry has been added to
the LT1226 so that the falling edge slew rate is enhanced
which balances the noninverting slew rate response.
Large Signal, AV = +25
Large Signal, AV = – 25
Input Considerations
Resistors in series with the inputs are recommended for
the LT1226 in applications where the differential input
voltage exceeds
±6V continuously or on a transient basis.
An example would be in noninverting configurations with
high input slew rates or when driving heavy capacitive
loads. The use of balanced source resistance at each input
is recommended for applications where DC accuracy
must be maximized.
Capacitive Loading
The LT1226 is stable with all capacitive loads. This is
accomplished by sensing the load induced output pole
and adding compensation at the amplifier gain node. As
the capacitive load increases, both the bandwidth and
phase margin decrease so there will be peaking in the
LT1226 AI03
LT1226 AI02
–
+
3
2
1
8
5k
0.1
F
7
6
4
0.1
F
V+
V –
LT1226
LT1226 AI01
相关PDF资料 |
PDF描述 |
|---|---|
| FTS-117-01-L-D | CONN HEADER 34POS DUAL .05" T/H |
| MCP6V27-E/MD | IC OPAMP DUAL AUTO-ZERO 8DFN |
| BZW04-213-E3/54 | TVS 400W 213V 5% UNIDIR DO-204AL |
| TSW-120-14-S-D | CONN HEADER 40POS .100" DL GOLD |
| SSQ-103-03-T-S-RA | CONN RCPT .100" 3PS R/A SGL TIN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1227 | 制造商:LINER 制造商全称:Linear Technology 功能描述:140MHz Video Current Feedback Amplifier |
| LT1227_06 | 制造商:LINER 制造商全称:Linear Technology 功能描述:140MHz Video Current Feedback Amplifier |
| LT1227C | 制造商:LINER 制造商全称:Linear Technology 功能描述:140MHz Video Current Feedback Amplifier |
| LT1227CN8 | 功能描述:IC VIDEO CURRNT FEEDBCK AMP 8DIP RoHS:否 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 标准包装:1,000 系列:- 应用:驱动器 输出类型:差分 电路数:3 -3db带宽:350MHz 转换速率:1000 V/µs 电流 - 电源:14.5mA 电流 - 输出 / 通道:60mA 电压 - 电源，单路/双路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安装类型:表面贴装 封装/外壳:20-VFQFN 裸露焊盘 供应商设备封装:20-QFN 裸露焊盘（4x4） 包装:带卷 (TR) |
| LT1227CN8#PBF | 功能描述:IC VIDEO CURRNT FEEDBCK AMP 8DIP RoHS:是 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 应用:TFT-LCD 面板：VCOM 驱动器 输出类型:满摆幅 电路数:1 -3db带宽:35MHz 转换速率:40 V/µs 电流 - 电源:3.7mA 电流 - 输出 / 通道:1.3A 电压 - 电源，单路/双路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽）裸露焊盘 供应商设备封装:8-uMax-EP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。