参数资料
| 型号： | LT1230CN |
| 厂商： | Linear Technology |
| 文件页数： | 16/16页 |
| 文件大小： | 0K |
| 描述： | IC CURRNT FEEDBCK AMP QUAD 14DIP |
| 标准包装： | 25 |
| 放大器类型： | 电流反馈 |
| 电路数： | 4 |
| 转换速率： | 2500 V/µs |
| -3db带宽： | 100MHz |
| 电流 - 输入偏压： | 10µA |
| 电压 - 输入偏移： | 3000µV |
| 电流 - 电源： | 6mA |
| 电流 - 输出 / 通道： | 125mA |
| 电压 - 电源，单路/双路(±)： | 4 V ~ 30 V，±2 V ~ 15 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 14-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 14-PDIP |
| 包装： | 管件 |
9
LT1229/LT1230
amplifier at 150
°C is less than 7mA and typically is only
4.5mA. The power in the IC due to the load is a function of
the output voltage, the supply voltage and load resistance.
The worst case occurs when the output voltage is at half
supply, if it can go that far, or its maximum value if it
cannot reach half supply.
For example, let’s calculate the worst case power dissipa-
tion in a video cable driver operating on
±12V supplies that
delivers a maximum of 2V into 150
.
Capacitive Loads
The LT1229/LT1230 can drive capacitive loads directly
when the proper value of feedback resistor is used. The
graph Maximum Capacitive Load vs Feedback Resistor
should be used to select the appropriate value. The value
shown is for 5dB peaking when driving a 1k load at a gain
of 2. This is a worst case condition; the amplifier is more
stable at higher gains and driving heavier loads. Alterna-
tively, a small resistor (10
to 20) can be put in series
with the output to isolate the capacitive load from the
amplifier output. This has the advantage that the amplifier
bandwidth is only reduced when the capacitive load is
present, and the disadvantage that the gain is a function of
the load resistance.
Power Supplies
The LT1229/LT1230 amplifiers will operate from single or
split supplies from
±2V (4V total) to ±15V (30V total). It is
not necessary to use equal value split supplies, however,
the offset voltage and inverting input bias current will
change. The offset voltage changes about 350
V per volt
of supply mismatch, the inverting bias current changes
about 2.5
A per volt of supply mismatch.
Power Dissipation
The LT1229/LT1230 amplifiers combine high speed and
large output current drive into very small packages. Be-
cause these amplifiers work over a very wide supply range,
it is possible to exceed the maximum junction temperature
under certain conditions. To ensure that the LT1229 and
LT1230 remain within their absolute maximum ratings,
we must calculate the worst case power dissipation,
define the maximum ambient temperature, select the
appropriate package and then calculate the maximum
junction temperature.
The worst case amplifier power dissipation is the total of
the quiescent current times the total power supply voltage
plus the power in the IC due to the load. The quiescent
supply current of the LT1229/LT1230 has a strong nega-
tive temperature coefficient. The supply current of each
U
S
A
O
PPLICATI
WU
U
I FOR ATIO
Now if that is the dual LT1229, the total power in the
package is twice that, or 0.602W. We now must calcu-
late how much the die temperature will rise above the
ambient. The total power dissipation times the thermal
resistance of the package gives the amount of tempera-
ture rise. For the above example, if we use the SO8
surface mount package, the thermal resistance is
150
°C/W junction to ambient in still air.
Temperature Rise = Pd (MAX) RθJA = 0.602W
150
°C/W = 90.3°C
The maximum junction temperature allowed in the plastic
package is 150
°C. Therefore, the maximum ambient al-
lowed is the maximum junction temperature less the
temperature rise.
Maximum Ambient = 150
°C – 90.3°C = 59.7°C
Note that this is less than the maximum of 70
°C that is
specified in the absolute maximum data listing. If we must
use this package at the maximum ambient we must lower
the supply voltage or reduce the output swing.
As a guideline to help in the selection of the LT1229/
LT1230 the following table describes the maximum sup-
ply voltage that can be used with each part in cable driving
applications.
PV I
V
R
PV
mA
V
W per Amp
d MAX
S S MAX
S
O MAX
L
d MAX
()
=+
=+
()
=+
=
2
2 12
7
12
2
150
0 168
0 133
0 301
–
–
..
.
相关PDF资料 |
PDF描述 |
|---|---|
| DF3-4P-2DS | CONN HEADER 4POS 2MM RT ANG TIN |
| 961210-5900-AR-TP | CONN HEADER R/A 10POS GOLD SMD |
| DF3-3P-2DS | CONN HEADER 3POS 2MM RT ANG TIN |
| TSM-104-02-T-DH-A | CONN HEADER .1" 8POS DUAL SMD |
| DF3-2P-2DS | CONN HEADER 2POS 2MM RT ANG TIN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1230CN#PBF | 功能描述:IC CURRNT FEEDBCK AMP QUAD 14DIP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:Excalibur™ 放大器类型:J-FET 电路数:1 输出类型:- 转换速率:45 V/µs 增益带宽积:10MHz -3db带宽:- 电流 - 输入偏压:20pA 电压 - 输入偏移:490µV 电流 - 电源:1.7mA 电流 - 输出 / 通道:48mA 电压 - 电源，单路/双路(±):4.5 V ~ 38 V，±2.25 V ~ 19 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:带卷 (TR) |
| LT1230CS | 制造商:Linear Technology 功能描述:OP Amp Quad Current Fdbk 制造商:Linear Technology 功能描述:OP Amp Quad Current Fdbk ±15V 14-Pin SOIC N |
| LT1230CS#PBF | 功能描述:IC CURR FEEDBACK AMP QUAD 14SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:- 放大器类型:通用 电路数:4 输出类型:- 转换速率:0.6 V/µs 增益带宽积:1MHz -3db带宽:- 电流 - 输入偏压:45nA 电压 - 输入偏移:2000µV 电流 - 电源:1.4mA 电流 - 输出 / 通道:40mA 电压 - 电源，单路/双路(±):3 V ~ 32 V，±1.5 V ~ 16 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:带卷 (TR) 其它名称:LM324ADTBR2G-NDLM324ADTBR2GOSTR |
| LT1230CS#TR | 功能描述:IC AMP CURR FEEDBACK QUAD 14SOIC RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:Excalibur™ 放大器类型:J-FET 电路数:1 输出类型:- 转换速率:45 V/µs 增益带宽积:10MHz -3db带宽:- 电流 - 输入偏压:20pA 电压 - 输入偏移:490µV 电流 - 电源:1.7mA 电流 - 输出 / 通道:48mA 电压 - 电源，单路/双路(±):4.5 V ~ 38 V，±2.25 V ~ 19 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:带卷 (TR) |
| LT1230CS#TRPBF | 功能描述:IC CURR FEEDBACK AMP QUAD 14SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:Excalibur™ 放大器类型:J-FET 电路数:1 输出类型:- 转换速率:45 V/µs 增益带宽积:10MHz -3db带宽:- 电流 - 输入偏压:20pA 电压 - 输入偏移:490µV 电流 - 电源:1.7mA 电流 - 输出 / 通道:48mA 电压 - 电源，单路/双路(±):4.5 V ~ 38 V，±2.25 V ~ 19 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。