- 您现在的位置：买卖IC网 > PDF目录15334 > LT1242IS8#TR (Linear Technology)IC REG CTRLR ISO PWM CM 8-SOIC PDF资料下载
参数资料
| 型号： | LT1242IS8#TR |
| 厂商： | Linear Technology |
| 文件页数： | 7/16页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR ISO PWM CM 8-SOIC |
| 标准包装： | 2,500 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 500kHz |
| 占空比： | 96% |
| 电源电压： | 11 V ~ 25 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 是 |
| 工作温度： | -40°C ~ 100°C |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 带卷 (TR) |
LT1241 Series
PI FU C TI
S
COMP (Pin 1) : Compensation Pin. This pin is the output of
the Error Amplifier and is made available for loop compen-
sation. It can also be used to adjust the maximum value of
the current sense clamp voltage to less than 1V. This pin
can source a minimum of 0.5mA (0.8mA typ) and sink a
minimum of 2mA (4mA typ)
FB (Pin 2) Voltage Feedback Pin. This pin is the inverting
input of the error amplifier. The output voltage is normally
fed back to this pin through a resistive divider. The non-
inverting input of the error amplifier is internally commit-
ted to a 2.5V reference point.
I SENSE (Pin 3): Current Sense Pin. This is the input to the
current sense comparator. The trip point of the compara-
tor is set by, and is proportional to, the output voltage of
the Error Amplifier.
R T /C T (Pin 4): The oscillator frequency and the deadtime
are set by connecting a resistor (R T ) from V REF to R T /C T
and a capacitor (C T ) from R T /C T to GND.
The rise time of the oscillator waveform is set by the RC
time constant of R T and C T . The fall time, which is equal to
the output deadtime, is set by a combination of the RC time
constant and the oscillator sink current (8.2mA typ).
GND (Pin 5): Ground.
OUTPUT (Pin 6): This pin is the output of a high current
totem pole output stage. It is capable of driving up to ± 1A
of current into a capacitive load such as the gate of a
MOSFET.
V CC (Pin 7): This pin is the positive supply of the control
IC.
V REF (Pin 8): Reference. This is the reference output of the
IC. The reference output is used to supply charging current
to the external timing resistor R T . The reference provides
biasing to a large portion of the internal circuitry, and is
used to generate several internal reference levels includ-
ing the V FB level and the current sense clamp voltage.
A PPLICATI
MINIMUM
S I FOR ATIO
connected from the R T /C T pin to ground. The charging
START-UP
DEVICE
OPERATING
THRESHOLD
MAXIMUM
VOLTAGE
DUTY CYCLE REPLACES
current for C T is determined by the value of R T . The
discharge current for C T is set by the difference between
LT1241
LT1242
LT1243
LT1244
LT1245
9.6V
16V
8.4V
16V
8.4V
7.6V
10V
7.6V
10V
7.6V
50%
100%
100%
50%
50%
NONE
UC1842
UC1843
UC1844
UC1845
the current supplied by R T and the discharge current of the
LT124X. The discharge current of the device is trimmed to
8.2mA. For large values of R T discharge time will be
determined by the discharge current of the device and the
value of C T . As the value of R T is reduced it will have more
Oscillator
The LT1241 series devices are fixed frequency current
mode pulse width modulators. The oscillator frequency
and the oscillator discharge current are both trimmed and
tightly specified to minimize the variations in frequency
and deadtime. The oscillator frequency is set by choosing
a resistor and capacitor combination, R T and C T . This RC
combination will determine both the frequency and the
maximum duty cycle. The resistor R T is connected from
V REF (Pin 8) to the R T /C T pin (Pin 4). The capacitor C T is
effect on the discharge time of C T . During an oscillator
cycle capacitor C T is charged to approximately 2.8V and
discharged to approximately 1.1V. The output is enabled
during the charge time of C T and disabled, in an off state,
during the discharge time of C T . The deadtime of the circuit
is equal to the discharge time of C T . The maximum duty
cycle is limited by controlling the deadtime of the oscilla-
tor. There are many combinations of R T and C T that will
yield a given oscillator frequency, however there is only
one combination that will yield a specific deadtime at that
frequency. Curves of oscillator frequency and deadtime
7
相关PDF资料 |
PDF描述 |
|---|---|
| VI-2WP-EY-F4 | CONVERTER MOD DC/DC 13.8V 50W |
| LT1244IS8#TRPBF | IC REG CTRLR ISO PWM CM 8-SOIC |
| GCM24DTBH | CONN EDGECARD 48POS R/A .156 SLD |
| VI-2WP-EY-B1 | CONVERTER MOD DC/DC 13.8V 50W |
| GCM24DTBD | CONN EDGECARD 48POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1242MJ8 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Current-Mode SMPS Controller |
| LT1242MJ8/883 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Current-Mode SMPS Controller |
| LT1242MJ8/883C | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Current-Mode SMPS Controller |
| LT1243 | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Speed Current Mode Pulse Width Modulators |
| LT1243CJ8 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Current-Mode SMPS Controller |
发布紧急采购，3分钟左右您将得到回复。