- 您现在的位置：买卖IC网 > PDF目录14011 > LT1308BCS8#TRPBF (Linear Technology)IC REG BOOST 5V 1A 8SOIC PDF资料下载
参数资料
| 型号： | LT1308BCS8#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 8/20页 |
| 文件大小： | 0K |
| 描述： | IC REG BOOST 5V 1A 8SOIC |
| 标准包装： | 2,500 |
| 类型： | 升压（升压） |
| 输出类型： | 固定 |
| 输出数： | 1 |
| 输出电压： | 5V |
| 输入电压： | 1 V ~ 10 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 600kHz |
| 电流 - 输出： | 1A |
| 同步整流器： | 无 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 8-SOIC |
LT1308A/LT1308B
APPLICATIONS INFORMATION
OPERATION
The LT1308A combines a current mode, ?xed frequency
PWM architecture with Burst Mode micropower opera-
tion to maintain high ef?ciency at light loads. Operation
can be best understood by referring to the block diagram
in Figure 2. Q1 and Q2 form a bandgap reference core
whose loop is closed around the output of the converter.
When V IN is 1V, the feedback voltage of 1.22V, along with
an 80mV drop across R5 and R6, forward biases Q1 and
Q2’s base collector junctions to 300mV. Because this is not
enough to saturate either transistor, FB can be at a higher
voltage than V IN . When there is no load, FB rises slightly
above 1.22V, causing V C (the error ampli?er’s output) to
decrease. When V C reaches the bias voltage on hyster-
etic comparator A1, A1’s output goes low, turning off
all circuitry except the input stage, error ampli?er and
low-battery detector. Total current consumption in this
state is 140μA. As output loading causes the FB voltage to
decrease, A1’s output goes high, enabling the rest of the IC.
Switch current is limited to approximately 400mA initially
after A1’s output goes high. If the load is light, the output
voltage (and FB voltage) will increase until A1’s output goes
low, turning off the rest of the LT1308A. Low frequency
ripple voltage appears at the output. The ripple frequency
is dependent on load current and output capacitance.
This Burst Mode operation keeps the output regulated
and reduces average current into the IC, resulting in high
ef?ciency even at load currents of 1mA or less.
If the output load increases suf?ciently, A1’s output
remains high, resulting in continuous operation. When the
LT1308A is running continuously, peak switch current is
controlled by V C to regulate the output voltage. The switch
is turned on at the beginning of each switch cycle. When
Low-battery detector A4’s open-collector output (LBO)
pulls low when the LBI pin voltage drops below 200mV.
There is no hysteresis in A4, allowing it to be used as an
ampli?er in some applications. The entire device is disabled
when the SHDN pin is brought low. To enable the converter,
SHDN must be at 1V or greater. It need not be tied to V IN
as on the LT1308.
The LT1308B differs from the LT1308A in that there is no
hysteresis in comparator A1. Also, the bias point on A1 is
set lower than on the LT1308B so that switching can occur
at inductor current less than 100mA. Because A1 has no
hysteresis, there is no Burst Mode operation at light loads
and the device continues switching at constant frequency.
This results in the absence of low frequency output voltage
ripple at the expense of ef?ciency.
The difference between the two devices is clearly illus-
trated in Figure 3. The top two traces in Figure 3 shows an
LT1308A/LT1308B circuit, using the components indicated
in Figure 1, set to a 5V output. Input voltage is 3V. Load
current is stepped from 50mA to 800mA for both circuits.
Low frequency Burst Mode operation voltage ripple is
observed on Trace A, while none is observed on Trace B.
At light loads, the LT1308B will begin to skip alternate cycles.
The load point at which this occurs can be decreased by
increasing the inductor value. However, output ripple will
continue to be signi?cantly less than the LT1308A output
ripple. Further, the LT1308B can be forced into micropower
mode, where I Q falls from 3mA to 200μA by sinking 40μA
or more out of the V C pin. This stops switching by causing
A1’s output to go low.
TRACE A: LT1308A
the summation of a signal representing switch current
and a ramp generator (introduced to avoid subharmonic
oscillations at duty factors greater than 50%) exceeds the
V C signal, comparator A2 changes state, resetting the ?ip-
?op and turning off the switch. Output voltage increases
as switch current is increased. The output, attenuated
by a resistor divider, appears at the FB pin, closing the
V OUT , 100mV/DIV
AC COUPLED
TRACE B: LT1308B
V OUT , 100mV/DIV
AC COUPLED
800mA
I LOAD
50mA
V IN = 3V
200μs/DIV
1308 F03
overall loop. Frequency compensation is provided by an
external series RC network connected between the V C pin
and ground.
(CIRCUIT OF FIGURE 1)
Figure 3. LT1308A Exhibits Burst Mode Operation Output
Voltage Ripple at 50mA Load, LT1308B Does Not
1308abfb
8
相关PDF资料 |
PDF描述 |
|---|---|
| LT1302CS8-5#TR | IC REG BOOST 5V 0.6A 8SOIC |
| GBC50DRES-S13 | CONN EDGECARD 100POS .100 EXTEND |
| 35ML18MEFC5X7 | CAP ALUM 18UF 35V 20% RADIAL |
| MAX6717AUKWED1+T | IC SUPERVISOR MPU SOT23-5 |
| 16ML33MEFC5X5 | CAP ALUM 33UF 16V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1308BIS8 | 功能描述:IC REG BOOST 5V 1A 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT1308BIS8#PBF | 功能描述:IC REG BOOST 5V 1A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LT1308BIS8#PBF | 制造商:Linear Technology 功能描述:DC-DC CONVERTER BOOST 600KHZ 3A SOIC 制造商:Linear Technology 功能描述:DC-DC CONVERTER, BOOST, 600KHZ, 3A, SOIC |
| LT1308BIS8#TR | 功能描述:IC REG BOOST 5V 1A 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT1308BIS8#TRPBF | 功能描述:IC REG BOOST 5V 1A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
发布紧急采购，3分钟左右您将得到回复。