参数资料
| 型号： | LT1332CSW#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 6/8页 |
| 文件大小： | 0K |
| 描述： | IC TXRX RS232 W/12V VPP 24-SOIC |
| 标准包装： | 32 |
| 类型： | 收发器 |
| 驱动器/接收器数： | 3/5 |
| 规程： | RS232 |
| 电源电压： | 2 V ~ 6 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 24-SOIC |
| 包装： | 管件 |
LT1332
6
work well in this application. When V– is powered from
an external supply, the filter capacitor can be considerably
smaller (C ≥ 0.1F). Ceramic capacitors work well under
these conditions. V– should be greater than –13.2V and
less than –6.5V.
C–: Commutating Capacitor Input. When the LT1332 is
used with a switching regulator, a charge pump capacitor
should be connected from the regulator’s switch pin to the
C– pin. Make the external capacitor 1F or larger with low
effective series resistance to maintain good charge pump
efficiency. Low ESR tantalum capacitors (ESR < 2Ω) work
well in this application. The C– pin should be left open
when V– is powered from an external supply.
DRIVER IN: RS232 Driver Input Pins. Inputs are TTL/
CMOS compatible, with threshold set to 1.2V. Unused
inputs should not float; tie them to VCC.
DRIVER OUT: Driver Outputs at RS232 Voltage Levels.
Outputs are in a high impedance state when in SHUT-
DOWN mode, or VCC = 0V. Outputs are fully short-circuit
protected from V– + 30V to V+ – 30V with the power on,
off or SHUTDOWN. Typical breakdowns are ±45V.
Applying higher voltages will not damage the device if
the overdrive is moderately current limited. Although
the outputs are protected, short circuits on one output
can load the power supply generator and may disrupt
the signal levels of the other outputs. The driver outputs
are protected against ESD to ±10kV for human body
model discharges.
RX IN: Receiver Inputs. These pins accept RS232 level
signals (±5V to ±30V) into a protected 5k terminating
resistor. The receiver inputs are protected against ESD
to ±10kV for human body model discharges. Each re-
ceiver provides 0.4V of hysteresis for noise immunity.
The receiver thresholds are specified at VCC = 3V. When
VCC varies from 2V to 6V, the lower threshold increases
about 3V. Regardless of these shifts, the device provides
accurate data from valid RS232 input signals. A graph
in the performance characteristics section shows typi-
cal changes in the thresholds. The active receiver (RXA,
Pin 10, S Package) remains functional in SHUTDOWN.
RX OUT: Receiver Outputs with TTL/CMOS Voltage Levels.
OutputsareinahighimpedancestagewheninSHUTDOWN
mode to allow data line sharing. Outputs are fully short-
circuit protected to ground or VCC with the power on, off
or in SHUTDOWN mode. The active receiver (RXA, Pin 15,
S Package) remains functional in SHUTDOWN.
PIN FUNCTIONS
ESD PROTECTION
ESD Test Circuit
TheRS232lineinputsoftheLT1332haveon-chipprotection
fromESDtransientsupto±10kV.Theprotectionstructures
act to divert the static discharge safely to system ground.
In order for the ESD protection to function effectively,
the power supply and ground pins of the LT1332 must
be connected to ground through low impedances. The
power supply decoupling capacitors and charge pump
storage capacitors provide this low impedance in normal
applications of the circuit. The only constraint is that low
ESR capacitors must be used for bypassing and charge
storage. ESD testing must be done with pins VCC, V+,
V– and GND shorted to ground or connected with low
ESR capacitors.
LT1332 TC
LT1332
1
2
3
4
5
6
7
8
9
10
11
12
24
23
22
21
20
19
18
17
16
15
14
13
–12V
0.1
F
0.1
F
3V
RS232
LINE PINS
PROTECTED
TO ±10kV
C–
DRIVER OUT
RX IN
DRIVER OUT
RX IN
DRIVER OUT
RXA IN
NC
V–
GND
DRIVER IN
RX OUT
DRIVER IN
RX OUT
DRIVER IN
RXA OUT
RS232 ON/OFF
V+
3V VCC
0.1
F
12V
相关PDF资料 |
PDF描述 |
|---|---|
| MC10EP16VADR2 | IC RCVR/DRVR 5V DIFF ECL 8-SOIC |
| LT1332CG#PBF | IC TXRX RS232 W/12V VPP 28-SSOP |
| LTC1324CS#TRPBF | IC TXRX LOCALTALK 5V SNGL 16SOIC |
| LT1138AIG#TRPBF | IC 5DRV/3RCV RS232 5V 28SSOP |
| VI-2TW-IW-B1 | CONVERTER MOD DC/DC 5.5V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1336 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Half-Bridge N-Channel Power MOSFET Driver with Boost Regulator |
| LT1336CN | 功能描述:IC MOSFET DRVR 1/2BRDG NCH 16DIP RoHS:否 类别:集成电路 (IC) >> PMIC - MOSFET，电桥驱动器 - 外部开关 系列:- 标准包装:5 系列:- 配置:低端 输入类型:非反相 延迟时间:600ns 电流 - 峰:12A 配置数:1 输出数:1 高端电压 - 最大（自引导启动）:- 电源电压:14.2 V ~ 15.8 V 工作温度:-20°C ~ 60°C 安装类型:通孔 封装/外壳:21-SIP 模块 供应商设备封装:模块 包装:散装 配用:BG2A-NF-ND - KIT DEV BOARD FOR IGBT 其它名称:835-1063 |
| LT1336CN#PBF | 功能描述:IC MOSFET DRVR 1/2BRDG NCH 16DIP RoHS:是 类别:集成电路 (IC) >> PMIC - MOSFET，电桥驱动器 - 外部开关 系列:- 标准包装:5 系列:- 配置:低端 输入类型:非反相 延迟时间:600ns 电流 - 峰:12A 配置数:1 输出数:1 高端电压 - 最大（自引导启动）:- 电源电压:14.2 V ~ 15.8 V 工作温度:-20°C ~ 60°C 安装类型:通孔 封装/外壳:21-SIP 模块 供应商设备封装:模块 包装:散装 配用:BG2A-NF-ND - KIT DEV BOARD FOR IGBT 其它名称:835-1063 |
| LT1336CS | 功能描述:IC MOSFET DRVR 1/2BRDG NCH16SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - MOSFET，电桥驱动器 - 外部开关 系列:- 标准包装:5 系列:- 配置:低端 输入类型:非反相 延迟时间:600ns 电流 - 峰:12A 配置数:1 输出数:1 高端电压 - 最大（自引导启动）:- 电源电压:14.2 V ~ 15.8 V 工作温度:-20°C ~ 60°C 安装类型:通孔 封装/外壳:21-SIP 模块 供应商设备封装:模块 包装:散装 配用:BG2A-NF-ND - KIT DEV BOARD FOR IGBT 其它名称:835-1063 |
| LT1336CS#PBF | 功能描述:IC MOSFET DRVR 1/2BRDG NCH16SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - MOSFET，电桥驱动器 - 外部开关 系列:- 标准包装:95 系列:- 配置:高端和低端，独立 输入类型:非反相 延迟时间:160ns 电流 - 峰:290mA 配置数:1 输出数:2 高端电压 - 最大（自引导启动）:600V 电源电压:10 V ~ 20 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:管件 产品目录页面:1381 (CN2011-ZH PDF) |
发布紧急采购，3分钟左右您将得到回复。