- 您现在的位置：买卖IC网 > PDF目录13843 > LT1371CSW#TR (Linear Technology)IC REG MULTI CONFIG ADJ 20SOIC PDF资料下载
参数资料
| 型号： | LT1371CSW#TR |
| 厂商： | Linear Technology |
| 文件页数： | 10/16页 |
| 文件大小： | 0K |
| 描述： | IC REG MULTI CONFIG ADJ 20SOIC |
| 标准包装： | 1,000 |
| 类型： | 降压（降压），升压（升压），反相，Cuk，回扫，正向转换器 |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.25 V ~ 35 V |
| 输入电压： | 2.7 V ~ 25 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 500kHz |
| 电流 - 输出： | 3A |
| 同步整流器： | 无 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SOIC（0.295"，7.50mm 宽） |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 20-SOIC |
LT1371
APPLICATIO S I FOR ATIO
Output Capacitor Ripple Current (RMS)
DC
I RIPPLE (RMS) = I OUT 1 – DC
generates a loop “zero” at 5kHz to 50kHz that is instrumen-
tal in giving acceptable loop phase margin. Ceramic ca-
pacitors remain capacitive to beyond 300kHz and usually
resonate with their ESL before ESR becomes effective.
= I OUT
V OUT – V IN
V IN
They are appropriate for input bypassing because of their
high ripple current ratings and tolerance of turn-on surges.
0.3(V IN )(V OUT – V IN )
DC = Switch Duty Cycle
Input Capacitors
The input capacitor of a boost converter is less critical due
to the fact that the input current waveform is triangular and
does not contain large squarewave currents as is found in
the output capacitor. Capacitors in the range of 10 μ F to
100 μ F, with an ESR of 0.2 ? or less, work well up to full 3A
switch current. Higher ESR capacitors may be acceptable
at low switch currents. Input capacitor ripple current for a
boost converter is :
I RIPPLE =
(f)(L)(V OUT )
f = 500kHz Switching Frequency
The input capacitor can see a very high surge current when
a battery or high capacitance source is connected “live”
and solid tantalum capacitors can fail under this condition.
Several manufacturers have developed tantalum capaci-
tors specially tested for surge capability (AVX TPS series,
for instance) but even these units may fail if the input
voltage approaches the maximum voltage rating of the
capacitor during a high surge. AVX recommends derating
capacitor voltage by 2:1 for high surge applications.
Output Diode
The suggested output diode (D1) is a 1N5821 Schottky or
its Motorola equivalent MBR330. It is rated at 3A average
forward current and 30V reverse voltage. Typical forward
voltage is 0.6V at 3A. The diode conducts current only
during switch OFF time. Peak reverse voltage for boost
converters is equal to regulator output voltage. Average
forward current in normal operation is equal to output
current.
Frequency Compensation
Loop frequency compensation is performed on the output
of the error amplifier (V C pin) with a series RC network.
The main pole is formed by the series capacitor and the
output impedance ( ≈ 500k ? ) of the error amplifier. The
pole falls in the range of 2Hz to 20Hz. The series resistor
creates a “zero” at 1kHz to 5kHz, which improves loop
stability and transient response. A second capacitor, typi-
cally one-tenth the size of the main compensation capaci-
tor, is sometimes used to reduce the switching frequency
ripple on the V C pin. V C pin ripple is caused by output
voltage ripple attenuated by the output divider and multi-
plied by the error amplifier. Without the second capacitor,
V C pin ripple is:
Ceramic, OS-CON and aluminum electrolytic capacitors
may also be used and have a high tolerance to turn-on
surges.
V C Pin Ripple =
1 .245(V RIPPLE )(g m )(R C )
(V OUT )
V RIPPLE = Output ripple (V P–P )
Ceramic Capacitors
Higher value, lower cost ceramic capacitors are now
becoming available in smaller case sizes. These are tempt-
ing for switching regulator use because of their very low
ESR. Unfortunately, the ESR is so low that it can cause
loop stability problems. Solid tantalum capacitor ESR
10
g m = Error amplifier transconductance
( ≈ 1500 μ mho)
R C = Series resistor on V C pin
V OUT = DC output voltage
To prevent irregular switching, V C pin ripple should be
kept below 50mV P–P . Worst-case V C pin ripple occurs at
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6715AUTWGD5+T | IC SUPERVISOR MPU SOT23-6 |
| MAX6715AUTVHD2+T | IC SUPERVISOR MPU SOT23-6 |
| LT1375IS8 | IC REG BUCK ADJ 1.5A 8SOIC |
| UUT1HR22MCL1GS | CAP ALUM 0.22UF 50V 20% SMD |
| MAX6715AUTVFD6+T | IC SUPERVISOR MPU SOT23-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1371CT7 | 功能描述:IC REG MULTI CONFIG ADJ TO220-7 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1371CT7#PBF | 功能描述:IC REG MULTI CONFIG ADJ TO220-7 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1371HV | 制造商:LINER 制造商全称:Linear Technology 功能描述:500kHz High Efficiency 3A Switching Regulator |
| LT1371HVCR | 功能描述:IC REG MULTI CONFIG ADJ 3A D2PAK RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1371HVCR#PBF | 功能描述:IC REG MULTI CONFIG ADJ 3A D2PAK RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
发布紧急采购，3分钟左右您将得到回复。