- 您现在的位置：买卖IC网 > PDF目录14798 > LT1373IS8#PBF (Linear Technology)IC REG MULTI CONFIG ADJ 8SOIC PDF资料下载
参数资料
| 型号： | LT1373IS8#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 7/12页 |
| 文件大小： | 0K |
| 描述： | IC REG MULTI CONFIG ADJ 8SOIC |
| 标准包装： | 100 |
| 类型： | 降压（降压），升压（升压），反相，Cuk，回扫，正向转换器 |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.25 V ~ 35 V |
| 输入电压： | 2.7 V ~ 25 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 250kHz |
| 电流 - 输出： | 1.5A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 管件 |
| 供应商设备封装： | 8-SOIC |
| 产品目录页面： | 1327 (CN2011-ZH PDF) |
LT1373
APPLICATIO S I FOR ATIO
Negative Output Voltage Setting
The LT1373 develops a – 2.45V reference (V NFR ) from the
NFB pin to ground. Output voltage is set by connecting the
NFB pin to an output resistor divider (Figure 2). The – 7 μ A
NFB pin bias current (I NFB ) can cause output voltage errors
and should not be ignored. This has been accounted for in
the formula in Figure 2. The suggested value for R2 is
2.49k. The FB pin is normally left open for negative output
applications. See Dual Polarity Output Voltage Sensing for
limitations of FB pin loading when using the NFB pin.
A logic low on the S/S pin activates shutdown, reducing
the part’s supply current to 12 μ A. Typical synchronization
range is from 1.05 and 1.8 times the part’s natural switch-
ing frequency, but is only guaranteed between 300kHz and
340kHz. A 12 μ s resetable shutdown delay network guar-
antees the part will not go into shutdown while receiving
a synchronization signal.
Caution should be used when synchronizing above
330kHz because at higher sync frequencies the ampli-
tude of the internal slope compensation used to prevent
( )
–V OUT = V NFB 1 + R1 + I NFB (R1)
( )
R1 = 2.45
NFB
PIN
V NFR
I NFB
–V OUT
R1
R2
R2
? V OUT ? – 2.45
+ (7 ? 10 –6 )
R2
subharmonic switching is reduced. This type of
subharmonic switching only occurs when the duty cycle
of the switch is above 50%. Higher inductor values will
tend to eliminate problems.
Thermal Considerations
LT1373 ? F02
Figure 2. Negative Output Resistor Divider
Dual Polarity Output Voltage Sensing
Certain applications benefit from sensing both positive
and negative output voltages. One example is the Dual
Output Flyback Converter with Overvoltage Protection
circuit shown in the Typical Applications section. Each
output voltage resistor divider is individually set as de-
scribed above. When both the FB and NFB pins are used,
the LT1373 acts to prevent either output from going
beyond its set output voltage. For example in this applica-
tion, if the positive output were more heavily loaded than
the negative, the negative output would be greater and
would regulate at the desired set-point voltage. The posi-
tive output would sag slightly below its set-point voltage.
This technique prevents either output from going unregu-
lated high at no load. Please note that the load on the FB
pin should not exceed 100 μ A when the NFB pin is used.
This situation occurs when the resistor dividers are used
at both FB and NFB. True load on FB is not the full divider
current unless the positive output is shorted to ground.
See Dual Output Flyback Converter application.
Shutdown and Synchronization
The dual function S/S pin provides easy shutdown and
synchronization. It is logic level compatible and can be
pulled high, tied to V IN or left floating for normal operation.
Care should be taken to ensure that the worst-case input
voltage and load current conditions do not cause exces-
sive die temperatures. The packages are rated at 120 ° C/W
for SO (S8) and 130 ° C/W for PDIP (N8).
Average supply current (including driver current) is:
I IN = 1mA + DC (I SW /60 + I SW ? 0.004)
I SW = switch current
DC = switch duty cycle
Switch power dissipation is given by:
P SW = (I SW ) 2 ? R SW ? DC
R SW = output switch “On” resistance
Total power dissipation of the die is the sum of supply
current times supply voltage plus switch power:
P D(TOTAL) = (I IN ? V IN ) + P SW
Choosing the Inductor
For most applications the inductor will fall in the range of
10 μ H to 50 μ H. Lower values are chosen to reduce physical
size of the inductor. Higher values allow more output
current because they reduce peak current seen by the
power switch which has a 1.5A limit. Higher values also
reduce input ripple voltage, and reduce core loss.
When choosing an inductor you might have to consider
maximum load current, core and copper losses, allowable
7
相关PDF资料 |
PDF描述 |
|---|---|
| LT1372IS8#PBF | IC REG MULTI CONFIG ADJ 8SOIC |
| ABC05DRYI-S13 | CONN EDGECARD 10POS .100 EXTEND |
| LT1071CT#06PBF | IC REG MULTI CONFIG ADJ TO220-5 |
| RBC25DRYI | CONN EDGECARD 50POS DIP .100 SLD |
| LT1376HVIS8#PBF | IC REG BUCK ADJ 1.5A 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1374 | 制造商:LINER 制造商全称:Linear Technology 功能描述:4.5A, 500kHz Step-Down Switching Regulator |
| LT137415CS8 | 制造商:Linear Technology 功能描述: |
| LT1374C | 制造商:LINER 制造商全称:Linear Technology 功能描述:4.5A, 500kHz Step-Down Switching Regulator |
| LT1374CFE | 功能描述:IC REG BUCK ADJ 4.5A 16TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1374CFE#PBF | 功能描述:IC REG BUCK ADJ 4.5A 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
发布紧急采购，3分钟左右您将得到回复。