- 您现在的位置：买卖IC网 > PDF目录13970 > LT1376CS#TRPBF (Linear Technology)IC REG BUCK ADJ 1.5A 16SOIC PDF资料下载
参数资料
| 型号： | LT1376CS#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 10/28页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 1.5A 16SOIC |
| 标准包装： | 2,500 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 2.42 V ~ 21.5 V |
| 输入电压： | 5 V ~ 25 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 500kHz |
| 电流 - 输出： | 1.5A |
| 同步整流器： | 无 |
| 工作温度： | 0°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 16-SOIC |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LT1375/LT1376
APPLICATIO N S I N FOR M ATIO N
I OUT(MAX) = ( V OUT ) ( V IN ? V OUT )
2 ( L )( f )( V )
I P ?
( 5 ) ( 8 ? 5 )
()
2 ? ? 10 ? ? ?? 500 ? 10 ? ? 8
pinwhenoutputvoltageislow.Theequivalentcircuitryis
shown in Figure 2. Q1 is completely off during normal
operation. If the FB pin falls below 1V, Q1 begins to
conduct current and reduces frequency at the rate of
approximately 5kHz/ μ A. To ensure adequate frequency
foldback (under worst-case short-circuit conditions), the
external divider Thevinin resistance must be low enough
to pull 150 μ A out of the FB pin with 0.6V on the pin (R DIV
≤ 4k). The net result is that reductions in frequency and
current limit are affected by output voltage divider imped-
ance. Although divider impedance is not critical, caution
should be used if resistors are increased beyond the
suggested values and short-circuit conditions will occur
with high input voltage. High frequency pickup will in-
crease and the protection accorded by frequency and
current foldback will decrease.
formula assumes continuous mode operation, implying
that the term on the right is less than one-half of I P .
Continuous Mode
IN
For the conditions above and L = 10 μ H,
I OUT ( MAX ) = 1 . 44 ? ? 5 3
= 1 . 44 ? 0 . 19 = 1 . 25 A
At V IN = 15V, duty cycle is 33%, so I P is just equal to a fixed
2 ? 10 ? ?? 500 ? 10 ? ( 15 )
MAXIMUM OUTPUT LOAD CURRENT
Maximum load current for a buck converter is limited by
the maximum switch current rating (I P ) of the LT1376.
This current rating is 1.5A up to 50% duty cycle (DC),
decreasing to 1.35A at 80% duty cycle. This is shown
1.5A, and I OUT(MAX) is equal to:
1 . 5 ? ( 5 ) ( 15 ? 5 )
? 5 3
= 1 . 5 ? 0 . 33 = 1 . 17 A
graphically in Typical Performance Characteristics and as
shown in the formula below:
I P = 1.5A for DC ≤ 50%
I P = 1.65A – 0.15 (DC) – 0.26 (DC) 2 for 50% < DC < 90%
DC = Duty cycle = V OUT /V IN
Example: with V OUT = 5V, V IN = 8V; DC = 5/8 = 0.625, and;
I SW(MAX) = 1.64 – 0.15 (0.625) – 0.26 (0.625) 2 = 1.44A
Current rating decreases with duty cycle because the
Note that there is less load current available at the higher
input voltage because inductor ripple current increases.
This is not always the case. Certain combinations of
inductor value and input voltage range may yield lower
available load current at the lowest input voltage due to
reduced peak switch current at high duty cycles. If load
current is close to the maximum available, please check
maximum available current at both input voltage ex-
tremes. To calculate actual peak switch current with a
given set of conditions, use:
LT1376 has internal slope compensation to prevent cur-
rent mode subharmonic switching. For more details, read
Application Note 19. The LT1376 is a little unusual in this
regard because it has nonlinear slope compensation which
gives better compensation with less reduction in current
I SW ( PEAK ) = I OUT +
V OUT ( V IN ? V OUT )
2 ( L )( f )( V IN )
limit.
Maximum load current would be equal to maximum
For lighter loads where discontinuous operation can be
used, maximum load current is equal to:
( ) ( )( )( )
I f L V
) ( V ? V )
2 ( V
switch current for an infinitely large inductor, but with
finite inductor size, maximum load current is reduced by
one-half peak-to-peak inductor current. The following
I OUT(MAX) =
Discontinuous mode
2
P OUT
OUT IN OUT
13756fd
10
相关PDF资料 |
PDF描述 |
|---|---|
| V110B15C150BL | CONVERTER MOD DC/DC 15V 150W |
| LT1376CS#TR | IC REG BUCK ADJ 1.5A 16SOIC |
| V110B15C150B3 | CONVERTER MOD DC/DC 15V 150W |
| LT1054IN8 | IC REG SWITCHED CAP DBL INV 8DIP |
| LTC3536IMSE#PBF | IC REG BUCK BST SYNC ADJ 12MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1376HV | 制造商:LINER 制造商全称:Linear Technology 功能描述:1.5A, 500kHz Step-Down Switching Regulators |
| LT1376HVCS | 功能描述:IC REG BUCK ADJ 1.5A 16SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1376HVCS#PBF | 功能描述:IC REG BUCK ADJ 1.5A 16SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1376HVCS#TR | 功能描述:IC REG BUCK ADJ 1.5A 16SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1376HVCS#TRPBF | 功能描述:IC REG BUCK ADJ 1.5A 16SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
发布紧急采购，3分钟左右您将得到回复。