- 您现在的位置：买卖IC网 > PDF目录10794 > LT1394IS8#PBF (Linear Technology)IC COMPARATOR LOW PWR 7NS 8-SOIC PDF资料下载
参数资料
| 型号： | LT1394IS8#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 15/16页 |
| 文件大小： | 0K |
| 描述： | IC COMPARATOR LOW PWR 7NS 8-SOIC |
| 标准包装： | 100 |
| 系列： | UltraFast™ |
| 类型： | 带锁销 |
| 元件数： | 1 |
| 输出类型： | CMOS，补充型，TTL |
| 电压 - 输入偏移（最小值）： | 2.5mV @ ±5V |
| 电流 - 输入偏压（最小值）： | 4.5µA @ ±5V |
| 电流 - 输出（标准）： | 20mA |
| 电流 - 静态（最大值）： | 8.5mA |
| CMRR, PSRR（标准）： | 100dB CMRR，100dB PSRR |
| 传输延迟（最大）： | 9ns |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 安装类型： | 表面贴装 |
| 包装： | 管件 |
| 产品目录页面： | 1323 (CN2011-ZH PDF) |
8
LT1394
–
+
LT1394
1394 F02
FET PROBE
* TOTAL LEAD LENGTH INCLUDING DEVICE PIN.
SOCKET AND CAPACITOR LEADS SHOULD BE
LESS THAN 0.5 IN. USE GROUND PLANE
** (VOS + OVERDRIVE)/200
25
25
5V
0.01
F*
0.01
F
10k
50
V1**
2N3866
0V
–3V
–5V
50
PULSE
IN
750
400
0.1
F
130
0V
–100mV
Q
APPLICATIONS INFORMATION
WU
U
Figure 2. Response Time Test Circuit
circuit is the lack of feedthrough from the generator to the
comparator input. This prevents overshoot on the com-
parator input, which would give a false fast reading on
comparator response time.
To adjust the circuit for exactly 5mV overdrive, V1 is
adjusted so that the LT1394 output under test settles to
1.4V (in the linear region). Then V1 is changed by – 1V to
set overdrive to 5mV.
High Speed Design Techniques
A substantial amount of design effort has made the LT1394
relatively easy to use. It is much less prone to oscillation
than some slower comparators, even with slow input
signals. However, as with any high speed comparator,
there are a number of pitfalls which may arise because of
PC board layout and design. The most common problems
involve power supply bypassing. Bypassing is necessary
to maintain low supply impedance. DC resistance and
inductance in supply wires and PC traces can quickly build
up to unacceptable levels. This allows the supply line to
move with changing internal current levels of the con-
nected devices. This will almost always result in improper
operation. In addition, adjacent devices connected through
an unbypassed supply can interact with each other through
the finite supply impedances. Bypass capacitors furnish a
simple solution to this problem by providing a local
reservoir of energy at the device, keeping supply imped-
ances low.
Bypass capacitors should be as close as possible to the
LT1394. A good high frequency capacitor such as a 0.1
F
ceramic is recommended, in parallel with a larger capaci-
tor such as a 4.7
F tantalum.
Poor trace routes and high source impedances are also
common sources of problems. Be sure to keep trace
lengths as short as possible, and avoid running any output
trace adjacent to an input trace to prevent unnecessary
coupling. If output traces are longer than a few inches, be
sure to terminate them with a resistor to eliminate any
reflections that may occur. Resistor values are typically
250
to 400. Also, be sure to keep source impedances
as low as possible, preferably 1k
or less.
Crystal Oscillators
Figure 3’s circuits are crystal oscillators. In the circuit (a)
the resistors at the LT1394’s positive input set a DC bias
point. The 2k-0.068
F path sets up phase shifted feedback
and the circuit looks like a wideband unity-gain follower at
DC. The crystal’s path provides resonant positive feed-
back and stable oscillation occurs. The circuit (b) is
similar, but supports oscillation frequencies to 30MHz.
Above 10MHz, AT-cut crystals operate in overtone mode.
Because of this, oscillation can occur at multiples of the
desired frequency. The damper network rolls off gain at
high frequency, ensuring proper operation.
Switchable Output Crystal Oscillator
Figure 4 permits crystals to be electronically switched by
logic commands. This circuit is similar to the previous
examples, except that oscillation is only possible when
one of the logic inputs is biased high.
相关PDF资料 |
PDF描述 |
|---|---|
| LT1132ACSW#PBF | IC 5DRV/3RCV RS232 5V 24-SOIC |
| VI-J4J-MY-S | CONVERTER MOD DC/DC 36V 50W |
| B37981M1103K054 | CAP CER 10000PF 100V 10% RADIAL |
| LTC1444IS#PBF | IC COMP W/REF LOWPWR QUAD 16SOIC |
| VI-J43-MY-S | CONVERTER MOD DC/DC 24V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1395 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Single/Dual/Quad 400MHz Current Feedback Amplifier |
| LT1395_1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Single/Dual/Quad 400MHz Current Feedback Amplifier |
| LT1395CS5 | 制造商:Linear Technology 功能描述:OP Amp Single Current Fdbk ±6V/12V 5-Pin TSOT-23 |
| LT1395CS5#PBF | 制造商:Linear Technology 功能描述:OP-AMP, 400MHZ, 800V/us, TSOT-23-5; Op Amp Type:Current Feedback; No. of Amplifiers:1; Slew Rate:800V/s; Supply Voltage Range:4V to 12V; Amplifier Case Style:TSOT-23; No. of Pins:5; Bandwidth:400MHz; Operating Temperature Min:0C ;RoHS Compliant: Yes |
| LT1395CS5#TR | 功能描述:IC AMP CURR FEEDBK SNGL TSOT23-5 RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:160 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:10 V/µs 增益带宽积:9MHz -3db带宽:- 电流 - 输入偏压:1pA 电压 - 输入偏移:250µV 电流 - 电源:730µA 电流 - 输出 / 通道:28mA 电压 - 电源，单路/双路(±):2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。