- 您现在的位置：买卖IC网 > PDF目录14048 > LT1425CS#TRPBF (Linear Technology)IC REG FLYBK ISOLATED .2A 16SOIC PDF资料下载
参数资料
| 型号： | LT1425CS#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 11/20页 |
| 文件大小： | 0K |
| 描述： | IC REG FLYBK ISOLATED .2A 16SOIC |
| 标准包装： | 2,500 |
| 类型： | 回扫，隔离 |
| 输出数： | 1 |
| 输入电压： | 2.8 V ~ 20 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 285kHz |
| 电流 - 输出： | 200mA |
| 同步整流器： | 无 |
| 工作温度： | 0°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 16-SOIC |
LT1425
APPLICATIO N S I N FOR M ATIO N
) ) ) )
V BG
N SP
) )
R OUT = ESR
) ) ) )
? I SW
R OUT
) )
α =
SELECTING R FB AND R REF RESISTOR VALUES
The expression for V OUT developed in the Operation
section can be rearranged to yield the following expres-
sion for R FB :
V OUT + V F + I SEC (ESR ) α
R FB = R REF
The unknown parameter α , which represents the fraction
of R FB current flowing into the R REF node, can be repre-
sented instead by specified data sheet values as follows:
(I REF )( α )(3k) = V BG
V BG
(I REF )(3k)
Allowing the expression for R FB to be rewritten as:
R OCOMP , the external resistor value required for its nomi-
nal compensation:
1
1 – DC
? V RCCOMP R FB
R OCOMP = K1
While the value for R OCOMP may therefore be theoretically
determined, it is usually better in practice to employ
empirical methods. This is because several of the required
input variables are difficult to estimate precisely. For
instance, the ESR term above includes that of the trans-
former secondary, but its effective ESR value depends on
high frequency behavior, not simply DC winding resis-
tance. Similarly, K1 appears to be a simple ratio of V IN to
V OUT times (differential) efficiency, but theoretically esti-
R FB = R REF
)
V OUT + V F + I SEC (ESR)
I REF (3k)N SP
)
mating efficiency is not a simple calculation. The sug-
gested empirical method is as follows:
Build a prototype of the desired supply using the
where,
V OUT = Desired output voltage
V F = Switching diode forward voltage
(I SEC )(ESR) = Secondary resistive losses
I REF = Data sheet reference current value
N SP = Effective secondary-to-primary turns ratio
Strictly speaking, the above equation defines R FB not as an
absolute value, but as a ratio of R REF . So the next question
is, “What is the proper value for R REF ?” The answer is that
R REF should be approximately 3k. This is because the
LT1425 is trimmed and specified using this value of R REF .
If the impedance of R REF varies considerably from 3k,
additional errors will result. However, a variation in R REF
of several percent or so is perfectly acceptable. This yields
a bit of freedom in selecting standard 1% resistor values
to yield nominal R FB /R REF ratios.
SELECTING R OCOMP RESISTOR VALUE
The Operation section previously derived the following
expressions for R OUT , i.e., effective output impedance and
eventual secondary components. Temporarily ground
the R CCOMP pin to disable the load compensation func-
tion. Operate the supply over the expected range of
output current loading while measuring the output
voltage deviation. Approximate this variation as a single
value of R OUT (straight line approximation). Calculate a
value for the K1 constant based on V IN , V OUT and the
measured (differential) efficiency. They are then com-
bined with the data sheet typical value for ( ? V RCCOMP /
? I SW ) to yield a value for R OCOMP .
Verify this result by connecting a resistor of roughly this
value from the R OCOMP pin to ground. (Disconnect the
ground short to R CCOMP and connect the requisite
0.1 μ F filter capacitor to ground.) Measure the output
impedance with the new compensation in place. Modify
the original R OCOMP value if necessary to increase or
decrease the effective compensation.
Once the proper load compensation resistor has been
chosen, it may be necessary to adjust the value of the
R FB resistor. This is because the load compensation
system exhibits some nonlinearity. In particular, the
circuit can shift the reference current by a noticeable
11
相关PDF资料 |
PDF描述 |
|---|---|
| V24B8E200B | CONVERTER MOD DC/DC 8V 200W |
| 50PK2.2MEFCTA5X11 | CAP ALUM 2.2UF 50V 20% RADIAL |
| V24B12C150BG | CONVERTER MOD DC/DC 12V 150W |
| LT1425CS#TR | IC REG FLYBK ISOLATED .2A 16SOIC |
| 35MS54.7MEFCT54X5 | CAP ALUM 4.7UF 35V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1425IS | 功能描述:IC REG FLYBK ISOLATED .2A 16SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT1425IS#PBF | 功能描述:IC REG FLYBK ISOLATED .2A 16SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:MIC23xxx HyperLight Load™ Regulators 标准包装:5,000 系列:HyperLight Load® 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.8V 输入电压:2.7 V ~ 5.5 V PWM 型:混合物 频率 - 开关:4MHz 电流 - 输出:2A 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘，8-MLF? 包装:带卷 (TR) 供应商设备封装:8-MLF?（2x2） 产品目录页面:1094 (CN2011-ZH PDF) 其它名称:576-3303-2 |
| LT1425IS#TR | 功能描述:IC REG FLYBK ISOLATED .2A 16SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT1425IS#TRPBF | 功能描述:IC REG FLYBK ISOLATED .2A 16SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT1425ISPBF | 制造商:Linear Technology 功能描述:Sw. Regulator Isolated Flyback SOIC16 |
发布紧急采购，3分钟左右您将得到回复。