- 您现在的位置：买卖IC网 > PDF目录14049 > LT1425CS (Linear Technology)IC REG FLYBK ISOLATED .2A 16SOIC PDF资料下载
参数资料
| 型号： | LT1425CS |
| 厂商： | Linear Technology |
| 文件页数： | 14/20页 |
| 文件大小： | 0K |
| 描述： | IC REG FLYBK ISOLATED .2A 16SOIC |
| 标准包装： | 50 |
| 类型： | 回扫，隔离 |
| 输出数： | 1 |
| 输入电压： | 2.8 V ~ 20 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 285kHz |
| 电流 - 输出： | 200mA |
| 同步整流器： | 无 |
| 工作温度： | 0°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 包装： | 管件 |
| 供应商设备封装： | 16-SOIC |
LT1425
APPLICATIO N S I N FOR M ATIO N
) ) ) )
(V IN ? t ON ) 2
Min Power =
) ) ) )
1
I OUT(MIN) = (V IN ? t ON ) 2
) ) ) )
[V OUT ? (t EN + t ED )] 2
Min Power =
V F of this diode should therefore be included in R FB
calculations. Lot-to-lot and ambient temperature varia-
tions will show up as output voltage shift/drift.
Secondary Leakage Inductance
Leakage inductance on the transformer secondary
reduces the effective primary-to-secondary turns ratio
(N P /N S ) from its ideal value. This will increase the output
voltage target by a similar percentage. To the extent that
secondary leakage inductance is constant from part-to-
part, this can be accommodated by adjusting the R FB to
R REF resistor ratio.
Output Impedance Error
An additional error source is caused by transformer sec-
ondary current flow through the real life nonzero imped-
ances of the output rectifier, transformer secondary and
output capacitor. Because the secondary current only
flows during the off portion of the duty cycle, the effective
output impedance equals the “DC” lumped secondary
impedance times the inverse of the off duty cycle. If the
output load current remains relatively constant, or, in less
critical applications, the error may be judged acceptable
and the R FB value adjusted for nominal expected error. In
more demanding applications, output impedance error
may be minimized by the use of the load compensation
function (see Load Compensation).
V IN Sense Error
The LT1425 determines the size of the flyback pulse by
comparing the V SW signal to V IN , through R FB . This
comparison is not perfect, in the sense that an offset exists
between the sensing mechanism and the actual V IN . This
is expressed in the data sheet as V IN sense error. This error
is fixed in absolute millivolt terms relative to V OUT (with the
exception that it is reflected to V OUT by any nonunity
secondary-to-primary turns ratio).
MINIMUM LOAD CONSIDERATIONS
The LT1425 generally provides better low load perfor-
mance than previous generation switcher/controllers
utilizing indirect output voltage sensing techniques.
Specifically, it contains circuitry to detect flyback pulse
14
“collapse,” thereby supporting operation well into discon-
tinuous mode. Nevertheless, there still remain constraints
to ultimate low load operation. They relate to the minimum
switch ON time and the minimum enable time. Discontinu-
ous mode operation will be assumed in the following
theoretical derivations.
As outlined in the Operation section, the LT1425 utilizes a
minimum output switch ON time, t ON . This value can be
combined with expected V IN and switching frequency to
yield an expression for minimum delivered power.
1 f
2 L PRI
= (V OUT )(I OUT )
This expression then yields a minimum output current
constraint:
f
2 (L PRI )(V OUT )
where,
f = Switching frequency (nominally 285kHz)
L PRI = Transformer primary side inductance
V IN = Input voltage
V OUT = Output voltage
t ON = Output switch minimum ON time
An additional constraint has to do with the minimum
enable time. The LT1425 derives its output voltage infor-
mation from the flyback pulse. If the internal minimum
enable time pulse extends beyond the flyback pulse, loss
of regulation will occur. The onset of this condition can be
determined by setting the width of the flyback pulse equal
to the sum of the flyback enable delay, t ED , plus the
minimum enable time, t EN . Minimum power delivered to
the load is then:
1 f
2 L SEC
= (V OUT )(I OUT )
which yields a minimum output constraint:
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6868UK43D5S+T | IC MPU SUPERVISOR SOT23-5 |
| MAX6868UK44D3L+T | IC MPU SUPERVISOR SOT23-5 |
| MAX6868UK44D3S+T | IC MPU SUPERVISOR SOT23-5 |
| MAX6868UK43D6L+T | IC MPU SUPERVISOR SOT23-5 |
| RGM24DTKS | CONN EDGECARD 48POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1425CS#PBF | 功能描述:IC REG FLYBK ISOLATED .2A 16SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LT1425CS#TR | 功能描述:IC REG FLYBK ISOLATED .2A 16SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT1425CS#TRPBF | 功能描述:IC REG FLYBK ISOLATED .2A 16SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT1425CSPBF | 制造商:Linear Technology 功能描述:LT1425CSPBF |
| LT1425IS | 功能描述:IC REG FLYBK ISOLATED .2A 16SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
发布紧急采购，3分钟左右您将得到回复。