- 您现在的位置：买卖IC网 > PDF目录1822 > LT1505CG#TRPBF (Linear Technology)IC BATT CHARGER CONST I/V 28SSOP PDF资料下载
参数资料
| 型号： | LT1505CG#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 7/16页 |
| 文件大小： | 0K |
| 描述： | IC BATT CHARGER CONST I/V 28SSOP |
| 标准包装： | 2,000 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子，镍镉，镍氢 |
| 电源电压： | 11 V ~ 24 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 28-SSOP |
| 包装： | 带卷 (TR) |
LT1505
PI N FU N CTIO N S
the noninverting input to the amplifier, VA in the Block
Diagram, that controls the charging current when the
device operates in constant voltage mode. The amplifier
VA controls the charging current to maintain the voltage
on the V FB pin at the reference voltage (2.465V). Input bias
current for VA is approximately 3nA. The LT1505 incorpo-
rates a resistor divider that can be used to select the
correct voltage for either three or four 4.1V or 4.2V
lithium-ion cells. For three cells the 3CELL pin is shorted
to the V FB pin. For four cells the 3CELL pin is not con-
nected. For 4.1V cells the 4.1V pin is connected to the V FB
pin and the 4.2V pin is not connected. For 4.2V cells the
4.2V pin is connected to V FB and the 4.1V pin is not
connected. See the table below.
BAT2 (Pin 20): This pin is used to connect the battery to
the internal preset voltage setting resistor. An internal
switch disconnects the internal divider from the battery
when the device is in shutdown or when power is discon-
nected. This disconnect function eliminates the current
drain due to the resistor divider. This pin should be
connected to the positive node of the battery if the internal
preset divider is used. This pin should be grounded if an
external divider is used. Maximum input voltage on this
pin is 20V.
SENSE (Pin 21): This pin is the noninverting input to the
current amplifier CA1 in the Block Diagram. Typical bias
current is – 50 μ A.
SPIN (Pin 22): This pin is for the internal amplifier CA1
PRESET BATTERY VOLTAGE
12.3V (3 × 4.1V Cell)
16.4V (4 × 4.1V Cell)
12.6V (3 × 4.2V Cell)
16.8V (4 × 4.2V Cell)
PIN SELECTION
4.1V, V FB , 3CELL Short Together
4.1V, V FB , Short Together, 3CELL Floats
4.2V, V FB , 3CELL Short Together
4.2V, V FB , Short Together, 3CELL Floats
bias. It must be connected as shown in the application
circuit.
BAT (Pin 23): Current Amplifier CA1 Inverting Input.
Typical bias current is – 50 μ A.
For battery voltages other than the preset values, an
external resistor divider can be used. If an external divider
is used then the 4.1V, 4.2V and 3CELL pins should not be
connected and BAT2 pin should be grounded. To maintain
the tight voltage tolerance, the external resistors should
have better than 0.25% tolerance. Note that the V FB pin will
float high and inhibit switching if it is left open.
V C (Pin 18): This is the control signal of the inner loop of
the current mode PWM. Switching starts at 0.9V, higher
V C corresponds to higher charging current in normal
operation and reaches 1.1V at full charging current. A
capacitor of at least 0.33 μ F to GND filters out noise and
controls the rate of soft start. Pulling this pin low will stop
switching. Typical output current is 60 μ A.
PROG (Pin 19): This pin is for programming the charge
current and for system loop compensation. During normal
operation, V PROG stays at 2.465V. If it is shorted to GND or
more than 1mA is drawn out of the pin, switching will stop.
When a microprocessor controlled DAC is used to pro-
gram charging current, it must be capable of sinking
current at a compliance up to 2.465V.
V CC (Pin 24): Input Supply. For good bypass, a low ESR
capacitor of 10 μ F or higher is required. Keep the lead
length to a minimum. V CC should be between 11V and 24V.
Do not force V CC below V BAT by more than 1V with the
battery present.
BOOSTC (Pin 25): This pin is used to bootstrap and supply
the current sense amplifier CA1 for very low dropout
condition. V CC can be as low as only 0.4V above the battery
voltage. A diode and a capacitor are needed to get the
voltage from V BOOST . If low dropout is not needed and V CC
is always 3V or higher than V BAT , this pin can be left
floating or tied to V CC . Do not force this pin to a voltage
lower than V CC . Typical input current is 1mA.
GBIAS (Pin 26): This is the output of the internal 9.1V
regulator to power the drivers and control circuits. This pin
must be bypassed to a ground plane with a minimum of
2.2 μ F ceramic capacitor. Switching will stop when V GBIAS
drops below 7V.
BGATE (Pin 27): Low Side Power MOSFET Drive.
PGND (Pin 28): MOSFET Driver Power Ground. A solid
system ground plane is very important. See the LT1505
Demo Manual for further information.
1505fc
7
相关PDF资料 |
PDF描述 |
|---|---|
| LT1506IR-SYNC#PBF | IC REG BUCK ADJ 4.5A D2PAK |
| LT1507CN8#PBF | IC REG BUCK ADJ 1.5A 8DIP |
| LT1510-5IGN#TRPBF | IC BATT CHARGER CONST V/I 16SSOP |
| LT1511ISW#TRPBF | IC BATT CHRGR CONST I/V 3A24SOIC |
| LT1512IGN#TRPBF | IC BATT CHRGR CONST I/V 16-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1505G | 制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:1.5A GLASS PASSIVATED RECTIFIER |
| LT1506 | 制造商:LINER 制造商全称:Linear Technology 功能描述:4.5A, 500kHz Step-Down Switching Regulator |
| LT1506C | 制造商:LINER 制造商全称:Linear Technology 功能描述:4.5A, 500kHz Step-Down Switching Regulator |
| LT1506CR | 功能描述:IC REG BUCK ADJ 4.5A D2PAK RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1506CR#PBF | 功能描述:IC REG BUCK ADJ 4.5A D2PAK RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
发布紧急采购，3分钟左右您将得到回复。