- 您现在的位置：买卖IC网 > PDF目录13867 > LT1506IS8-3.3 (Linear Technology)IC REG BUCK 3.3V 4.5A 8SOIC PDF资料下载
参数资料
| 型号： | LT1506IS8-3.3 |
| 厂商： | Linear Technology |
| 文件页数： | 6/24页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK 3.3V 4.5A 8SOIC |
| 标准包装： | 100 |
| 类型： | 降压（降压） |
| 输出类型： | 固定 |
| 输出数： | 1 |
| 输出电压： | 3.3V |
| 输入电压： | 4 V ~ 15 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 500kHz |
| 电流 - 输出： | 4.5A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 管件 |
| 供应商设备封装： | 8-SOIC |
LT1506
PI N FU N CTIO N S
FB/SENSE: The feedback pin is used to set output voltage
using an external voltage divider that generates 2.42V at
the pin with the desired output voltage. The fixed voltage
(-3.3) parts have the divider included on the chip and the
FB pin is used as a SENSE pin, connected directly to the
3.3V output. Three additional functions are performed by
the FB pin. When the pin voltage drops below 1.7V, switch
current limit is reduced. Below 1.5V the external sync
function is disabled. Below 1V, switching frequency is also
reduced. See Feedback Pin Function section in Applica-
tions Information for details.
BOOST: The BOOST pin is used to provide a drive voltage,
higher than the input voltage, to the internal bipolar NPN
power switch. Without this added voltage, the typical
switch voltage loss would be about 1.5V. The additional
boost voltage allows the switch to saturate and voltage
loss approximates that of a 0.07 ? FET structure, but with
much smaller die area. Efficiency improves from 75% for
conventional bipolar designs to > 89% for these new parts.
V IN : This is the collector of the on-chip power NPN switch.
This pin powers the internal circuitry and internal regula-
tor. At NPN switch on and off, high dI/dt edges occur on
this pin. Keep the external bypass and catch diode close to
this pin. All trace inductance on this path will create a
voltage spike at switch off, adding to the V CE voltage
across the internal NPN.
GND: The GND pin connection needs consideration for
two reasons. First, it acts as the reference for the regulated
output, so load regulation will suffer if the “ground” end of
the load is not at the same voltage as the GND pin of the
IC. This condition will occur when load current or other
currents flow through metal paths between the GND pin
and the load ground point. Keep the ground path short
between the GND pin and the load and use a ground plane
when possible. The second consideration is EMI caused
by GND pin current spikes. Internal capacitance between
the V SW pin and the GND pin creates very narrow (<10ns)
6
current spikes in the GND pin. If the GND pin is connected
to system ground with a long metal trace, this trace may
radiate excess EMI. Keep the path between the input
bypass and the GND pin short. The GND pin of the SO-8
package is directly attached to the internal tab. This pin
should be attached to a large copper area to improve
thermal resistance.
V SW : The switch pin is the emitter of the on-chip power
NPN switch. This pin is driven up to the input pin voltage
during switch on time. Inductor current drives the switch
pin negative during switch off time. Negative voltage is
clamped with the external catch diode. Maximum negative
switch voltage allowed is – 0.8V.
SYNC: The sync pin is used to synchronize the internal
oscillator to an external signal. It is directly logic compat-
ible and can be driven with any signal between 10% and
90% duty cycle. The synchronizing range is equal to initial
operating frequency, up to 1MHz. This pin replaces SHDN
on -SYNC option parts. See Synchronizing section in
Applications Information for details. When not in use, this
pin should be grounded.
SHDN: The shutdown pin is used to turn off the regulator
and to reduce input drain current to a few microamperes.
Actually, this pin has two separate thresholds, one at
2.38V to disable switching, and a second at 0.4V to force
complete micropower shutdown. The 2.38V threshold
functions as an accurate undervoltage lockout (UVLO).
This is sometimes used to prevent the regulator from
operating until the input votlage has reached a predeter-
mined level.
V C : The V C pin is the output of the error amplifier and the
input of the peak switch current comparator. It is normally
used for frequency compensation, but can do double duty
as a current clamp or control loop override. This pin sits
at about 1V for very light loads and 2V at maximum load.
It can be driven to ground to shut off the regulator, but if
driven high, current must be limited to 4mA.
相关PDF资料 |
PDF描述 |
|---|---|
| L06031R5DGWTR | INDUCTOR THIN FILM 1.5NH 0603 |
| V375B15E200B3 | CONVERTER MOD DC/DC 15V 200W |
| HMC20DREF-S13 | CONN EDGECARD 40POS .100 EXTEND |
| GSC28DRTI-S13 | CONN EDGECARD 56POS .100 EXTEND |
| GMC28DRTI-S13 | CONN EDGECARD 56POS .100 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1507 | 制造商:LINER 制造商全称:Linear Technology 功能描述:500kHz Monolithic Buck Mode Switching Regulator |
| LT1507C | 制造商:LINER 制造商全称:Linear Technology 功能描述:500kHz Monolithic Buck Mode Switching Regulator |
| LT1507CN8 | 功能描述:IC REG BUCK ADJ 1.5A 8DIP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT1507CN8#PBF | 功能描述:IC REG BUCK ADJ 1.5A 8DIP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:20 系列:SIMPLE SWITCHER® 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:12V 输入电压:4 V ~ 60 V PWM 型:电压模式 频率 - 开关:52kHz 电流 - 输出:1A 同步整流器:无 工作温度:-40°C ~ 125°C 安装类型:通孔 封装/外壳:16-DIP（0.300"，7.62mm） 包装:管件 供应商设备封装:16-DIP 其它名称:*LM2575HVN-12LM2575HVN-12 |
| LT1507CN8-3.3 | 功能描述:IC REG BUCK 3.3V 1.5A 8DIP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
发布紧急采购，3分钟左右您将得到回复。