- 您现在的位置：买卖IC网 > PDF目录13971 > LT1507CS8-3.3#TR (Linear Technology)IC REG BUCK 3.3V 1.5A 8SOIC PDF资料下载
参数资料
| 型号： | LT1507CS8-3.3#TR |
| 厂商： | Linear Technology |
| 文件页数： | 16/20页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK 3.3V 1.5A 8SOIC |
| 标准包装： | 2,500 |
| 类型： | 降压（降压） |
| 输出类型： | 固定 |
| 输出数： | 1 |
| 输出电压： | 3.3V |
| 输入电压： | 4 V ~ 15 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 500kHz |
| 电流 - 输出： | 1.5A |
| 同步整流器： | 无 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 8-SOIC |
LT1507
APPLICATIO N S I N FOR M ATIO N
The circuit in Figure 6 will allow operation at light loads
with low input voltages. It uses a small PNP to charge the
boost capacitor (C2) and an extra diode (D3) to complete
the power path from V SW to the boost capacitor. Note that
the diodes have been changed to Schottky BAT85s to
optimize low voltage operation. Figure 5 shows that with
the added PNP, minimum load current can be reduced to
6mA and still guarantee proper start-up with 4.7V input.
D2
BAT85
problems. For low input voltage, high sync frequency
applications, the circuit shown in Figure 7 can be used to
generate an external slope compensation ramp that elimi-
nates subharmonic oscillation. See Frequency Compen-
sation section for a discussion of an entirely different
cause of subharmonic switching before assuming that the
cause is insufficient slope compensation. Application Note
19 has more details on the theory of slope compensation.
C2
0.22 μ F
D3
BAT85
SYNC
LT1507
GND
V SW
V C
+
V OUT
INPUT
V IN
BOOST
V SW
L1
V OUT = 3.3V
C S
1000pF
R C
470 ?
+
LT1507-3.3
SENSE
Q1
2N3906
R S
5.2k
C C
2000pF
GND
V C
C C
D1
1N5818
+
C1
LT1507 ? F07
Figure 7. Adding External Slope Compensation for High
Sync Frequencies
LT1507 ? F06
Figure 6. Adding a Small PNP to Reduce Minimum
Start-Up Voltage
SYNCHRONIZING
The LT1507 SYNC pin is used to synchronize the internal
oscillator to an external signal. It is directly logic compat-
ible and can be driven with any signal between 10% and
90% duty cycle. The synchronizing range is equal to initial
operating frequency up to 1MHz (above 700kHz external
slope compensation may be needed). This means that
minimum practical sync frequency is equal to the worst-
case high self-oscillating frequency (560kHz) not the
typical operating frequency of 500kHz. Caution should be
used when synchronizing above 700kHz because at higher
sync frequencies, the amplitude of the internal slope
compensation used to prevent subharmonic switching is
reduced. This type of subharmonic switching only occurs
at input voltages less than twice the output voltage and
shows up as alternating pulse widths at the switch node.
It does not cause the regulator to lose regulation, but
switch frequency content down to 100kHz may be objec-
tionable. Higher inductor values will tend to eliminate
16
External Slope Compensation Ramp
The LT1507 is a current mode switching regulator and
therefore, it requires something called “slope compensa-
tion” when operated above 50% duty cycle in continuous
mode. This condition occurs when input voltage is less
than twice output voltage. Slope compensation adds a
ramp to the switch current sense signal generated on the
chip during switch ON time. Typically the ramp is gener-
ated from a portion of the internal oscillator waveform. In
the LT1507, the ramp is arranged to be zero until the
oscillator waveform reaches about 40% of its final value.
This minimizes the total amount of ramp added to switch
current. The reason for doing it this way is that the ramp
subtracts from switch current limit, so that switch current
limit would be considerably lower at high duty cycle
compared to low duty cycle if the ramp existed at all duty
cycles. By starting the ramp at the 40% point, changes in
current limit are minimized. No ramp is needed when
operating below 50% duty cycle.
Problems can occur with this technique if the regulator is
used with a combination of high external sync frequency
and more than 50% duty cycle. The basic sync function
相关PDF资料 |
PDF描述 |
|---|---|
| GEM15DTBN-S273 | CONN EDGECARD 30POS R/A .156 SLD |
| LT1376CS8-5#TRPBF | IC REG BUCK 5V 1.5A 8SOIC |
| LT1376CS8-5#TR | IC REG BUCK 5V 1.5A 8SOIC |
| LT3433EFE#TRPBF | IC REG BUCK BST ADJ 0.5A 16TSSOP |
| HM61-20270LFTR13 | INJECTION MOULDED INDUCTORS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1507CS8PBF | 制造商:Linear Technology 功能描述:LT1507CS8PBF |
| LT1507G | 制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:1.5A GLASS PASSIVATED RECTIFIER |
| LT1507I | 制造商:LINER 制造商全称:Linear Technology 功能描述:500kHz Monolithic Buck Mode Switching Regulator |
| LT1507IN8 | 功能描述:IC REG BUCK ADJ 1.5A 8DIP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1507IN8#PBF | 功能描述:IC REG BUCK ADJ 1.5A 8DIP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
发布紧急采购，3分钟左右您将得到回复。