- 您现在的位置：买卖IC网 > PDF目录16301 > LT1510CGN#PBF (Linear Technology)IC BATT CHARGER CONST V/I 16SSOP PDF资料下载
参数资料
| 型号： | LT1510CGN#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 9/16页 |
| 文件大小： | 0K |
| 描述： | IC BATT CHARGER CONST V/I 16SSOP |
| 标准包装： | 100 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子，镍镉，镍氢 |
| 电源电压： | 6.2 V ~ 28 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SSOP |
| 包装： | 管件 |
| 产品目录页面： | 1340 (CN2011-ZH PDF) |
LT1510/LT1510-5
APPLICATIO N S I N FOR M ATIO N
( )
0 . 29 V BAT ? 1 ? BAT ?
I RMS =
capacity ceramic capacitor (5 μ F to 10 μ F) from Tokin or
United Chemi-Con/MARCON, et al., and the old standby,
aluminum electrolytic, which will require more microfarads
to achieve adequate ripple rating. OS-CON can also be used.
The output capacitor C OUT is also assumed to absorb
output switching current ripple. The general formula for
capacitor current is:
? V ?
? V CC ?
( L 1 )( f )
For example, with V CC = 16V, V BAT = 8.4V, L1 = 30 μ H and
f = 200kHz, I RMS = 0.2A.
EMI considerations usually make it desirable to minimize
ripple current in the battery leads, and beads or inductors
may be added to increase battery impedance at the 200kHz
switching frequency. Switching ripple current splits be-
tween the battery and the output capacitor depending on
the ESR of the output capacitor and the battery impedance.
If the ESR of C OUT is 0.2 ? and the battery impedance is
raised to 4 ? with a bead of inductor, only 5% of the current
ripple will flow in the battery.
deliver full power to the load when the input voltage is still
well below its final value. If the adapter is current limited,
it cannot deliver full power at reduced output voltages and
the possibility exists for a quasi “latch” state where the
adapter output stays in a current limited state at reduced
output voltage. For instance, if maximum charger plus
computer load power is 20W, a 24V adapter might be
current limited at 1A. If adapter voltage is less than (20W/1A
= 20V) when full power is drawn, the adapter voltage will be
sucked down by the constant 20W load until it reaches a
lower stable state where the switching regulators can no
longer supply full load. This situation can be prevented by
utilizing undevoltage lockout, set higher than the minimum
adapter voltage where full power can be achieved.
A fixed undervoltage lockout of 7V is built into the V CC pin.
Internal lockout is performed by clamping the V C pin low.
The V C pin is released from its clamped state when the V CC
pin rises above 7V. The charger will start delivering current
about 2ms after V C is released, as set by the 0.1 μ F at V C
pin. Higher lockout voltage can be implemented with a
Zener diode (see Figure 3 circuit).
V IN
Soft Start
The LT1510 is soft started by the 0.1 μ F capacitor on V C
V Z
2k
D1
1N4001
V C
V CC
LT1510
GND
( )(
)
(
)
I BAT PROG 2000 = ?
? 2 . 465 V ?
? 2000
pin. On start-up, V C pin voltage will rise quickly to 0.5V,
then ramp at a rate set by the internal 45 μ A pull-up current
and the external capacitor. Battery charging current starts
ramping up when V C voltage reaches 0.7V and full current
is achieved with V C at 1.1V. With a 0.1 μ F capacitor, time to
reach full charge current is about 3ms and it is assumed
that input voltage to the charger will reach full value in less
than 3ms. Capacitance can be increased up to 0.47 μ F if
longer input start-up times are needed.
In any switching regulator, conventional timer-based soft
starting can be defeated if the input voltage rises much
slower than the time-out period. This happens because the
switching regulators in the battery charger and the com-
puter power supply are typically supplying a fixed amount
of power to the load. If input voltage comes up slowly
compared to the soft start time, the regulators will try to
1510 F03
Figure 3. Undervoltage Lockout
The lockout voltage will be V IN = V Z + 1V.
For example, for a 24V adapter to start charging at 22V IN ,
choose V Z = 21V. When V IN is less than 22V, D1 keeps V C
low and charger off.
Charging Current Programming
The basic formula for charging current is (see Block
Diagram):
= I
? R PROG ?
9
相关PDF资料 |
PDF描述 |
|---|---|
| UPM1E332MHD6 | CAP ALUM 3300UF 25V 20% RADIAL |
| ECO-S1CA333DA | CAP ALUM 33000UF 16V 20% SNAP |
| GBM25DTKN | CONN EDGECARD 50POS DIP .156 SLD |
| SEK471M025ST | CAP ALUM 470UF 25V 20% RADIAL |
| PCX1C221MCL1GS | CAP ALUM 220UF 16V 20% SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1510CN | 功能描述:IC BATT CHARGER CONST V/I 16-DIP RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LT1510CN#PBF | 功能描述:IC BATT CHARGER CONST V/I 16-DIP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LT1510CS | 功能描述:IC BATT CHARGER CONST V/I 16SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LT1510CS#PBF | 功能描述:IC BATT CHARGER CONST V/I 16SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
| LT1510CS#PBF | 制造商:Linear Technology 功能描述:Battery Management IC 制造商:Linear Technology 功能描述:IC, BATTERY CHARGER, 1.5A, SOIC-16 |
发布紧急采购，3分钟左右您将得到回复。