参数资料
型号: LT1512CS8
厂商: Linear Technology
文件页数: 5/12页
文件大小: 0K
描述: IC BATT CHRGR CONST I/V 8-SOIC
标准包装: 100
功能: 充电管理
电池化学: 所有电池类型
电源电压: 2.7 V ~ 25 V
工作温度: 0°C ~ 70°C
安装类型: 表面贴装
封装/外壳: 8-SOIC(0.154",3.90mm 宽)
供应商设备封装: 8-SOIC
包装: 管件
LT1512
PIN FUNCTIONS
I FB : The current feedback pin is used to sense charging
current. It is the input to a current sense ampli?er that
controls charging current when the battery voltage is below
the programmed voltage. During constant-current opera-
tion, the I FB pin regulates at –100mV. Input resistance of
this pin is 5kΩ, so ?lter resistance (R4, Figure 1) should be
less than 50Ω. The 24Ω, 0.22μF ?lter shown in Figure 1 is
used to convert the pulsating current in the sense resistor
to a smooth DC current feedback signal.
S/S: This pin can be used for shutdown and/or synchro-
nization. It is logic level compatible, but can be tied to V IN
if desired. It defaults to a high ON state when ?oated. A
logic low state will shut down the charger to a micropower
state. Driving the S/S pin with a continuous logic signal of
600kHz to 800kHz will synchronize switching frequency
to the external signal. Shutdown is avoided in this mode
with an internal timer.
V IN : The input supply pin should be bypassed with a
low ESR capacitor located right next to the IC chip. The
BLOCK DIAGRAM
V IN
grounded end of the capacitor must be connected directly
to the ground plane to which the GND pin is connected.
GND S, GND: The LT1512 uses separate ground pins for
switch current (GND) and the control circuitry (GND S).
This isolates the control ground from any induced volt-
age created by fast switch currents. Both pins should be
tied directly to the ground plane, but the external control
circuit components such as the voltage divider, frequency
compensation network and I FB bypass capacitor should be
connected directly to the GND S pin or to the ground plane
close to the point where the GND S pin is connected.
V SW : The switch pin is the collector of the power switch,
carrying up to 1.5A of current with fast rise and fall times.
Keep the traces on this pin as short as possible to mini-
mize radiation and voltage spikes. In particular, the path
in Figure 1 which includes SW to C2, D1, C1 and around
to the LT1512 ground pin should be as short as possible
to minimize voltage spikes at switch turn-off.
SW
S/S
SHUTDOWN
DELAY AND RESET
LOW DROPOUT
2.3V REG
ANTI-SAT
SYNC
500kHz
OSC
LOGIC
DRIVER
SWITCH
+
I FB
5k
62k
I FBA
COMP
+
FB
1.245V
REF
EA
V C
A V ≈ 6
IA
0.08Ω
GND
1512 F02
GND S
Figure 2
1512fa
5
相关PDF资料
PDF描述
SRU3014-220Y INDUCTOR 22UH 320MA SMD
RCM08DTMT-S189 CONN EDGECARD 16POS R/A .156 SLD
PCS0J221MCL9GS CAP ALUM 220UF 6.3V 20% SMD
SRU3014-1R5Y INDUCTOR 1.5UH 1.55A SMD
M3CMK-3420K IDC CABLE - MKC34K/MC34F/MCG34K
相关代理商/技术参数
参数描述
LT1512CS8#PBF 功能描述:IC BATT CHRGR CONST I/V 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料,电量检测计/监控器 电池化学:锂离子(Li-Ion) 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP,8-MSOP(0.118",3.00mm 宽) 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2
LT1512CS8#TR 功能描述:IC CHARGER BATT CONST V/I 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性,锂离子,镍镉,镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR)
LT1512CS8#TRPBF 功能描述:IC BATT CHRGR CONST I/V 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性,锂离子,镍镉,镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR)
LT1512CS8PBF 制造商:Linear Technology 功能描述:LT1512CS8PBF
LT1512I 制造商:LINER 制造商全称:Linear Technology 功能描述:SEPIC Constant-Current/ Constant-Voltage Battery Charger