- 您现在的位置：买卖IC网 > PDF目录16302 > LT1513-2CR (Linear Technology)IC BATT CHRGR CONST/PROG I/V 7DD PDF资料下载
参数资料
| 型号： | LT1513-2CR |
| 厂商： | Linear Technology |
| 文件页数： | 5/16页 |
| 文件大小： | 0K |
| 描述： | IC BATT CHRGR CONST/PROG I/V 7DD |
| 标准包装： | 50 |
| 功能： | 充电管理 |
| 电池化学： | 所有电池类型 |
| 电源电压： | 2.7 V ~ 25 V |
| 工作温度： | 0°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | TO-263-8，D²Pak（7 引线+接片），TO-263CA |
| 供应商设备封装： | D2PAK-7 |
| 包装： | 管件 |
LT1513/LT1513-2
PI N FU N CTIO N S
V C (Pin 1): The compensation pin is primarily used for
frequency compensation, but it can also be used for soft
starting and current limiting. It is the output of the error
amplifier and the input of the current comparator. Peak
switch current increases from 0A to 3.6A as the V C voltage
varies from 1V to 1.9V. Current out of the V C pin is about
200 μ A when the pin is externally clamped below the
internal 1.9V clamp level. Loop frequency compensation
is performed with a capacitor or series RC network from
the V C pin directly to the ground pin (avoid ground loops).
FB (Pin 2): The feedback pin is used for positive output
voltage sensing. The R1/R2 voltage divider connected to
FB defines Li-Ion float voltage at full charge, or acts as a
voltage limiter for NiCd or NiMH applications. FB is the
inverting input to the voltage error amplifier. Input bias
current is typically 300nA, so divider current is normally
set to 100 μ A to swamp out any output voltage errors due
to bias current. The noninverting input of this amplifier is
tied internally to a 1.245V reference. The grounded end of
the output voltage divider should be connected directly to
the LT1513 ground pin (avoid ground loops).
I FB (Pin 3): The current feedback pin is used to sense
charging current. It is the input to a current sense amplifier
that controls charging current when the battery voltage is
below a programmed limit. During constant-current
operation, the LT1513 I FB pin regulates at – 100mV. Input
resistance of this pin is 5k ? , so filter resistance (R4,
Figure 1) should be less than 50 ? . The 39 ? , 0.22 μ F filter
shown in Figure 1 is used to convert the pulsating current
in the sense resistor to a smooth DC current feedback
GND (Pin 4): The ground pin is common to both control
circuitry and switch current. V C , FB and S/S signals must
be Kelvin and connected as close as possible to this pin.
The TAB of the R package should also be connected to the
power ground.
V SW (Pin 5): The switch pin is the collector of the power
switch, carrying up to 3A of current with fast rise and fall
times. Keep the traces on this pin as short as possible to
minimize radiation and voltage spikes. In particular, the
path in Figure 1 which includes SW to C2, D1, C1 and
around to the LT1513 ground pin should be as short as
possible to minimize voltage spikes at switch turn-off.
S/S (Pin 6): This pin can be used for shutdown and/or
synchronization. It is logic level compatible, but can be
tied to V IN if desired. It defaults to a high ON state when
floated. A logic low state will shut down the charger to a
micropower state. Driving the S/S pin with a continuous
logic signal of 600kHz to 800kHz will synchronize switch-
ing frequency to the external signal. Shutdown is avoided
in this mode with an internal timer.
V IN (Pin 7): The input supply pin should be bypassed with
a low ESR capacitor located right next to the IC chip. The
grounded end of the capacitor must be connected directly
to the ground plane to which the TAB is connected.
TAB: The TAB on the surface mount R package is electri-
cally connected to the ground pin, but a low inductance
connection must be made to both the TAB and the pin for
proper circuit operation. See suggested PC layout in
Figure 4.
signal. The LT1513-2 I FB pin regulates at 0mV to provide
programmable current limit. The current through R5,
Figure 5, is balanced by the current through R4, program-
ming the maximum voltage across R3.
sn1513 1513fas
5
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4008EGN-1#PBF | IC BATT CHARGER CTRLR 4A 20SSOP |
| M3BYK-1606R | IDC CABLE - MSR16K/MC16M/MPD16K |
| M1YXK-2436J | IDC CABLE - MPD24K/MC24G/X |
| LTC4006EGN-6#PBF | IC CHARGER BATTERY 4A 16-SSOP |
| M2MXH-6018R | IDC CABLE - MDM60H/MC60M/X |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1513-2CR#PBF | 功能描述:IC BATT CHRGR CONST/PROG I/V 7DD RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
| LT1513-2CR#TR | 功能描述:IC CHARGER BATTERY FIXED V/I 7DD RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LT1513-2CR#TRPBF | 功能描述:IC BATT CHRGR CONST/PROG I/V 7DD RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LT1513-2CT7 | 功能描述:IC BATT CHG CNST/PROG I/V TO2207 RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
| LT1513-2CT7#PBF | 功能描述:IC CUR-MODE SW-REG SEPIC T0220-7 RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。