- 您现在的位置：买卖IC网 > PDF目录1822 > LT1533IS#TRPBF (Linear Technology)IC REG PUSH-PLL CTRLR ISO 16SOIC PDF资料下载
参数资料
| 型号： | LT1533IS#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 5/20页 |
| 文件大小： | 0K |
| 描述： | IC REG PUSH-PLL CTRLR ISO 16SOIC |
| 标准包装： | 2,500 |
| 类型： | 推挽式控制器，隔离式 |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.3 V ~ 30 V |
| 输入电压： | 2.7 V ~ 23 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 200kHz ~ 250kHz |
| 电流 - 输出： | 1A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 16-SOIC |
LT1533
PI N FU N CTIO N S
COL A, COL B (Pins 2, 15): These are the output collectors
of the power switches. Their emitters return to PGND
through a common sense resistor. COL A and
COL B are alternately turned on out of phase. Large
currents flow into these pins so it is desirable to keep
external trace lengths short to minimize radiation. The
collectors can be tied together for simple boost applica-
tions.
DUTY (Pin 3): Tying the DUTY pin to ground will force the
outputs to switch with a 50% duty cycle. The DUTY pin
must float if not used.
SYNC (Pin 4): The SYNC pin can be used to synchronize
the oscillator to an external clock (see Oscillator Sync in
Applications Information section for more details). The
SYNC pin may either be floated or tied to ground if not
used.
C T (Pin 5): The oscillator capacitor pin is used in conjunc-
tion with R T to set the oscillator frequency. For R T = 16.9k,
C T(NF) = 129/f OSC(kHz)
R T (Pin 6): The oscillator resistor pin is used to set the
charge and discharge currents of the oscillator capacitor.
The nominal value is 16.9k. It is possible to adjust this
resistance ± 25% to get a more accurate oscillator fre-
quency.
FB (Pin 7): The feedback pin is used for positive voltage
sensing and oscillator frequency shifting during start-up
and short-circuit conditions. It is the inverting input to the
error amplifier. The noninverting input of this amplifier
connects internally to a 1.25V reference. This pin should
be left open if not used.
NFB (Pin 8): The negative voltage feedback pin is used for
sensing a negative output voltage. The pin is connected to
the inverting input of the negative feedback amplifier
through a 100k source resistor. The negative feedback
amplifier provides a gain of – 0.5 to the feedback amplifier.
The nominal regulation point would be – 2.5V on NFB. This
GND (Pin 9): Signal Ground. The internal error amplifier,
negative feedback amplifier, oscillator, slew control cir-
cuitry and the bandgap reference are referred to this
ground. Keep the connection to the feedback divider and
V C compensation network free of large ground currents.
V C (Pin 10): The compensation pin is used for frequency
compensation and current limiting. It is the output of the
error amplifier and the input of the current comparator.
Loop frequency compensation can be performed with an
RC network connected from the V C pin to ground.
SHDN (Pin 11): The shutdown pin is used for disabling the
switcher. Grounding this pin will disable all internal cir-
cuitry. Normally this output can be tied high (to V IN ) or may
be left floating.
R CSL (Pin 12): A resistor to ground sets the current slew
rate for the collectors A and B. The minimum resistor value
is 3.9k and the maximum value is 68k. Current slew will be
approximately:
I SLEW(A/ μ s) = 33/R CSL(k ? )
R VSL (Pin 13): A resistor to ground sets the voltage slew
rate for the collectors A and B. The minimum resistor value
is 3.9k and the maximum value is 68k. Voltage slew will be
approximately:
V SLEW(V/ μ s) = 220/R VSL(k ? )
V IN (Pin 14): Input Supply Pin. Bypass this pin with a
≥ 4.7 μ F low ESR capacitor. When V IN is below 2.55V the
part will go into undervoltage lockout where it will stop
output switching and pull the V C pin low.
PGND (Pin 16): Power Switch Ground. This ground comes
from the emitters of the power switches. In normal opera-
tion this pin should have approximately 25nH inductance
to ground. This can be done by trace inductance (approxi-
mately 1") or with wire or a specific inductive component.
This inductance ensures stability in the current slew
control loop during turn-off. Too much inductance (>50nH)
may produce oscillation on the output voltage slew edges.
pin should be left open if not used.
5
相关PDF资料 |
PDF描述 |
|---|---|
| LT1534IS#TRPBF | IC REG BOOST ADJ 2A 16SOIC |
| LT1571EGN-2#TRPBF | IC CHARGER BATT CONST V/I 28SSOP |
| LT1572CS#TRPBF | IC REG MULTI CONFIG 1.25A 16SOIC |
| LT1576CS8-5SYNC#PBF | IC REG BUCK 5V 1.5A 8SOIC |
| LT1578IS8-2.5#PBF | IC REG BUCK 2.5V 1.5A 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1534 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Ultralow Noise 2A Switching Regulators |
| LT1534-1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Ultralow Noise 2A Switching Regulators |
| LT-1534-501-024 | 制造商:Carling Technologies 功能描述:LT-SERIES TOGGLE SWITCH - Bulk |
| LT-1534-510-012 | 制造商:Carling Technologies 功能描述:LT-SERIES TOGGLE SWITCH - Bulk |
| LT-1534-510-024 | 制造商:Carling Technologies 功能描述:LT-SERIES TOGGLE SWITCH - Bulk |
发布紧急采购，3分钟左右您将得到回复。