- 您现在的位置：买卖IC网 > PDF目录13955 > LT1534CS-1 (Linear Technology)IC REG BOOST ADJ 2A 16SOIC PDF资料下载
参数资料
| 型号： | LT1534CS-1 |
| 厂商： | Linear Technology |
| 文件页数： | 11/16页 |
| 文件大小： | 0K |
| 描述： | IC REG BOOST ADJ 2A 16SOIC |
| 标准包装： | 50 |
| 类型： | 升压（升压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.3 V ~ 35 V |
| 输入电压： | 2.7 V ~ 23 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 200kHz ~ 250kHz |
| 电流 - 输出： | 2A |
| 同步整流器： | 无 |
| 工作温度： | 0°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 包装： | 管件 |
| 供应商设备封装： | 16-SOIC |
LT1534/LT1534-1
APPLICATIO N S I N FOR M ATIO N
where ? I is the ripple current in the switch, R CSL and
R VSL are the slew resistors and f OSC is the oscillator
frequency.
Power dissipation P D is the sum of these three terms. Die
junction temperature is then computed as:
poor quality (high ESR) output capacitors are used. The
addition of a 0.0047 μ F capacitor on the V C pin reduces
switching frequency ripple to only a few millivolts. A low
value for R VC will also reduce V C pin ripple, but loop phase
margin may be inadequate.
T J = T AMB + (P D )( θ JA )
where T AMB is ambient temperature and θ JA is the package
thermal resistance. For the 16-pin SO with fused leads the
θ JA is 50 ° C/W.
For example, with f OSC = 40kHz, 0.4A average current and
R VC
2k
C VC
0.01 μ F
C VC2
4.7nF
Figure 4
V C PIN
1534 F03
0.1A of ripple, the maximum duty cycle is 88%. Assume
( 1 . 25 )( V RIPPLE )( g m )( R VC )
slew resistors are both 17k and V SAT is 0.26V, then:
P D = 0.176W + 0.094W + 0.158W = 0.429W
In an S16 fused lead package the die junction temperature
would be 21 ° C above ambient.
Frequency Compensation
Loop frequency compensation is accomplished by way of
a series RC network on the output of the error amplifier (V C
pin). Referring to Figure 4, the main pole is formed by
capacitor C VC and the output impedance of the error
amplifier (approximately 400k ? ). The series resistor R VC
creates a “zero” which improves loop stability and tran-
sient response. A second capacitor C VC2 , typically one-
tenth the size of the main compensation capacitor, is
sometimes used to reduce the switching frequency ripple
on the V C pin. V C pin ripple is caused by output voltage
ripple attenuated by the output divider and multiplied by
the error amplifier. Without the second capacitor, V C pin
ripple is:
V CPIN RIPPLE =
V OUT
where V RIPPLE = Output ripple (V P-P )
g m = Error amplifier transconductance
R VC = Series resistor on V C pin
V OUT = DC output voltage
To prevent irregular switching, V C pin ripple should be
kept below 50mV P-P . Worst-case V C pin ripple occurs at
maximum output load current and will also be increased if
Capacitors
While the IC reduces the source of switcher noise, it is
essential for the lowest noise, that the filter capacitors
should have low parasitic impedance. Sanyo OS-CON,
Panasonic Specialty Polymer and tantalum capacitors are
the preferred types. Aluminum electrolytics are not suit-
able for this application. In general, ESR is more critical
than capacitance. At higher frequencies, ESL can also be
important. Paralleling capacitors can reduce both ESR and
ESL.
Design Note 95 offers more information about capacitor
selection. The following is a brief summary:
Solid tantalum capacitors have small size and low
impedance. Typically they are available for voltages
below 50V. They may have a problem with surge
currents (AVX TPS line addresses this issue).
OS-CON capacitors have very low impedance but are
only available for 25V or less. Form factor may be a
problem. Sometimes their very low ESR can cause loop
stability problems.
Ceramic capacitors are generally used for high fre-
quency and high voltage bypass. They too can have
such a low ESR as to cause loop stability problems.
Often they can resonate with their ESL before ESR
becomes effective.
Specialty Polymer Aluminum: Panasonic has come out
with their series CD capacitors. While they are only
available for voltages below 16V, they have very low
ESR and good surge capability.
11
相关PDF资料 |
PDF描述 |
|---|---|
| GCA44DRMD | CONN EDGECARD 88POS .125 SQ WW |
| LTC3421EUF | IC REG BOOST SYNC ADJ 1.5A 24QFN |
| 35MH722MEFC6.3X7 | CAP ALUM 22UF 35V 20% RADIAL |
| EYM25DTBT | CONN EDGECARD 50POS R/A .156 SLD |
| 100YXM1MEFC5X11 | CAP ALUM 1UF 100V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1534CS-1#PBF | 功能描述:IC REG BOOST ADJ 2A 16SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT1534CS-1#TR | 功能描述:IC REG BOOST ADJ 2A 16SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT1534CS-1#TRPBF | 功能描述:IC REG BOOST ADJ 2A 16SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT1534I | 制造商:LINER 制造商全称:Linear Technology 功能描述:Ultralow Noise 2A Switching Regulators |
| LT1534IS | 功能描述:IC REG BOOST ADJ 2A 16SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
发布紧急采购，3分钟左右您将得到回复。