- 您现在的位置：买卖IC网 > PDF目录377707 > LT1534IS-1 (LINEAR TECHNOLOGY CORP) RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS PDF资料下载
参数资料
| 型号： | LT1534IS-1 |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| 中文描述： | 2 A SWITCHING REGULATOR, 250 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封装： | 0.150 INCH, PLASTIC, SOP-16 |
| 文件页数： | 6/16页 |
| 文件大小： | 222K |
| 代理商： | LT1534IS-1 |
6
LT1534/LT1534-1
PI
FU
CTIO
N
S
U
U
COL (Pins 2, 15/Pin 2):
These two pins should be con-
nected together externally to create the collector of the
power switch. The emitter returns to PGND through a
sense resistor. Large currents flow into these pins so it is
desirable to keep external trace lengths short to minimize
radiation.
SYNC (Pin 4):
The SYNC pin can be used to synchronize
the oscillator to an external clock (see Oscillator Sync in
Applications Information section for more details). The
SYNC pin may either be floated or tied to ground if not
used.
C
T
(Pin 5):
The oscillator capacitor pin is used in
conjunction with R
T
to set the oscillator frequency.
For R
T
= 16.9k,
C
T(NF)
= 129/f
OSC(kHz)
R
T
(Pin 6):
The oscillator resistor pin is used to set the
charge and discharge currents of the oscillator capacitor.
The nominal value is 16.9k. It is possible to adjust this
resistance
±
25% to get a more accurate oscillator fre-
quency.
FB (Pin 7):
The feedback pin is used for positive voltage
sensing and oscillator frequency shifting during start-up
and short-circuit conditions. It is the inverting input to the
error amplifier. The noninverting input of this amplifier
connects internally to a 1.25V reference. This pin should
be left open if not used.
NFB (Pin 8/Pin 10):
The negative voltage feedback pin is
used for sensing a negative output voltage. The pin is
connected to the inverting input of the negative feedback
amplifier through a 100k source resistor. The negative
feedback amplifier provides a gain of –0.5 to the feedback
amplifier; therefore, the nominal regulation point is –2.5V
on NFB. This pin should be left open if not used.
GND (Pin 9/Pins 1, 8, 9, 16):
Signal Ground. The internal
error amplifier, negative feedback amplifier, oscillator,
slew control circuitry and the bandgap reference are
referred to this ground. Keep the connection to the feed-
back divider and V
C
compensation network free of large
ground currents.
V
C
(Pin 10/Pin 11):
The compensation pin is used for
frequency compensation and current limiting. It is the
output of the error amplifier and the input of the current
comparator. Loop frequency compensation can be per-
formed with an RC network connected from the V
C
pin to
ground.
SHDN (Pin 11/Pin 12):
The shutdown pin is used for
disabling the switcher. Grounding this pin will disable all
internal circuitry. Normally this output can be tied high (to
V
IN
) or may be left floating.
R
CSL
(Pin 12/Pin 13):
A resistor to ground sets the current
slew rate for the power switch. The minimum resistor
value is 3.9k and the maximum value is 68k. Current slew
will be approximately:
I
SLEW(A/
μ
s)
= 33/R
CSL(k
)
R
VSL
(Pin 13/Pin 14):
A resistor to ground sets the voltage
slew rate for the power switch collector. The minimum
resistor value is 3.9k and the maximum value is 68k.
Voltage slew will be approximately:
V
SLEW(V/
μ
s)
= 220/R
VSL(k
)
V
IN
(Pin 14/Pin 15):
Input Supply Pin. Bypass this pin with
a
≥
4.7
μ
F low ESR capacitor. When V
IN
is below 2.55V the
part will go into undervoltage lockout where it will stop
output switching and pull the V
C
pin low.
PGND (Pin 16/Pin 3):
Power Switch Ground. This ground
comes from the emitters of the power switches. In normal
operation this pin should have approximately 25nH induc-
tance to ground. This can be done by trace inductance
(approximately 1") or with wire or a specific inductive
component (e.g., small ferrite bead). This inductance
ensures stability in the current slew control loop during
turn-off. Too much inductance (>50nH) may produce
oscillation on the output voltage slew edges.
(LT1534/LT1534-1)
相关PDF资料 |
PDF描述 |
|---|---|
| LT1534-1 | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| LT1534CS-1 | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| LT1534 | Octal Bus Transceivers 20-PDIP 0 to 70 |
| LT1534C | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| LT1534CS | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1534IS-1#PBF | 功能描述:IC REG BOOST ADJ 2A 16SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1534IS-1#TR | 功能描述:IC REG BOOST ADJ 2A 16SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1534IS-1#TRPBF | 功能描述:IC REG BOOST ADJ 2A 16SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1537 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Advanced Low Power 5V RS232 Transceiver with Small Capacitors |
| LT1537C | 制造商:LINER 制造商全称:Linear Technology 功能描述:Advanced Low Power 5V RS232 Transceiver with Small Capacitors |
发布紧急采购，3分钟左右您将得到回复。