- 您现在的位置：买卖IC网 > PDF目录13904 > LT1534IS (Linear Technology)IC REG BOOST ADJ 2A 16SOIC PDF资料下载
参数资料
| 型号： | LT1534IS |
| 厂商： | Linear Technology |
| 文件页数： | 8/16页 |
| 文件大小： | 0K |
| 描述： | IC REG BOOST ADJ 2A 16SOIC |
| 标准包装： | 50 |
| 类型： | 升压（升压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.3 V ~ 35 V |
| 输入电压： | 2.7 V ~ 23 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 200kHz ~ 250kHz |
| 电流 - 输出： | 2A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 包装： | 管件 |
| 供应商设备封装： | 16-SOIC |
LT1534/LT1534-1
OPERATIO
The negative feedback amplifier allows for direct regula-
tion of negative output voltages. The voltage on the NFB
pin gets amplified by a gain of – 0.5 and driven onto the FB
input, i.e., the NFB pin regulates to – 2.5V while the
amplifier output internally drives the FB pin to 1.25V as in
normal operation. The negative feedback amplifier input
impedance is 100k (typ) referred to ground.
Slew Control
Control of output voltage and current slew rates is done via
two feedback loops. One loop controls the output switch
collector voltage dV/dt and the other loop controls the
emitter current dI/dt. Output slew control is achieved by
comparing the currents generated by these two slewing
events to currents created by external resistors R VSL and
R CSL . The two control loops are combined internally to
provide a smooth transition from current slew control to
voltage slew control.
APPLICATIO N S I N FOR M ATIO N
Reducing EMI from switching power supplies has tradi-
tionally invoked fear in designers. Many switchers are
designed solely on efficiency and as such produce wave-
forms filled with high frequency harmonics that then
propagate through the rest of the power supply.
The LT1534 provides control over two of the more impor-
tant variables for controlling EMI with switching inductive
loads: switch voltage slew rate and switch current slew
rate. The use of this part will reduce noise and EMI over
conventional switch mode controllers. Because these
variables are under control, a supply built with this part will
exhibit far less tendency to create EMI and less chance of
wandering into problems during production.
It is beyond the scope of this data sheet to get into EMI
fundamentals. AN70 contains much information concern-
ing noise in switching regulators and should be consulted.
Oscillator Frequency
The oscillator determines the switching frequency and
therefore the fundamental positioning of all harmonics.
The use of good quality external components is important
to ensure oscillator frequency stability. The oscillator is a
8
Internal Regulator
Most of the control circuitry operates from an internal 2.4V
low dropout regulator that is powered from V IN . The
internal low dropout design allows V IN to vary from 2.7V
to 23V with virtually no change in device performance.
When the part is put into shutdown, the internal regulator
is turned off, leaving only a small (12 μ A typ) current drain
from V IN .
Protection Features
There are three modes of protection in the LT1534. The
first is overcurrent limit. This is achieved via the clamping
action of the V C pin. The second is thermal shutdown that
disables both output drivers and pulls the V C pin low in the
event of excessive chip temperature. The third is under-
voltage lockout that also disables both outputs
and pulls the V C pin low whenever V IN drops below 2.5V.
sawtooth design. A current defined by external resistor R T
is used to charge and discharge the capacitor C T . The
discharge rate is approximately ten times the charge rate.
By allowing the user to have control over both compo-
nents, trimming of oscillator frequency can be more easily
achieved.
The external capacitance C T is chosen by:
C T(nF) = 2180/[f OSC(kHz) ? R T(k ? ) ]
where f OSC is the desired oscillator frequency in kHz.
For R T equal to 16.9k, this simplifies to:
C T(nF) = 129/f OSC(kHz)
(e.g., C T = 1.29nF for f OSC = 100kHz)
A good quality temperature stable capacitor should be
chosen.
Nominally R T should be 16.9k. Since it sets up current, its
temperature coefficient should be selected to compliment
the capacitor. Ideally, both should have low temperature
coefficients.
相关PDF资料 |
PDF描述 |
|---|---|
| HM53-40111VLF | HIGH POWER LOW COST INDUCTORS |
| RCM31DCMN-S288 | CONN EDGECARD 62POS .156 EXTEND |
| VE-J3K-EZ-F3 | CONVERTER MOD DC/DC 40V 25W |
| VE-J3K-EZ-F2 | CONVERTER MOD DC/DC 40V 25W |
| RCM31DCMH-S288 | CONN EDGECARD 62POS .156 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1534IS#PBF | 功能描述:IC REG BOOST ADJ 2A 16SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1534IS#TR | 功能描述:IC REG BOOST ADJ 2A 16SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1534IS#TRPBF | 功能描述:IC REG BOOST ADJ 2A 16SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:20 系列:SIMPLE SWITCHER® 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:12V 输入电压:4 V ~ 60 V PWM 型:电压模式 频率 - 开关:52kHz 电流 - 输出:1A 同步整流器:无 工作温度:-40°C ~ 125°C 安装类型:通孔 封装/外壳:16-DIP（0.300"，7.62mm） 包装:管件 供应商设备封装:16-DIP 其它名称:*LM2575HVN-12LM2575HVN-12 |
| LT1534IS-1 | 功能描述:IC REG BOOST ADJ 2A 16SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1534IS-1#PBF | 功能描述:IC REG BOOST ADJ 2A 16SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
发布紧急采购，3分钟左右您将得到回复。