- 您现在的位置：买卖IC网 > PDF目录377707 > LT1573C (Linear Technology Corporation) Low Dropout PNP Regulator Driver PDF资料下载
参数资料
| 型号： | LT1573C |
| 厂商： | Linear Technology Corporation |
| 英文描述： | Low Dropout PNP Regulator Driver |
| 中文描述： | 低压差稳压器驱动进步党 |
| 文件页数： | 5/16页 |
| 文件大小： | 200K |
| 代理商： | LT1573C |
5
LT1573
activated by applying a voltage > 1.3V to the SHDN pin. The
output voltage will restart as soon as the SHDN pin is
pulled below the shutdown threshold. If the shutdown/
reset function is not used, the pin should be grounded. The
voltage applied to the SHDN pin can be higher than the
input voltage. When the SHDN pin voltage is higher than
2V, the SHDN pin current increases and is limited by an
internal 20k resistor.
GND (Pin 4):
Circuit Ground.
DRIVE (Pin 5):
The DRIVE pin is connected to the collector
of the main drive transistor of the LT1573. This drive
transistor sinks the base current of the external PNP
output transistor. A resistor is normally inserted between
the base of the external PNP output transistor and the
DRIVE pin. This resistor is sized to allow the LT1573 to
sink the appropriate amount of base current for a given
application and to activate the overcurrent latch in a fault
condition.
V
IN
(Pin 6):
This pin provides power to all internal circuitry
of the LT1573 including bias, start-up, thermal limit, error
amplifier and all overcurrent latch circuitry.
V
OUT
(Pin 7):
The V
OUT
pin is the input to comparator C1
shown in Block Diagram. This pin is normally connected
to the output. The comparator C1 is used to disable the
overcurrent latch during start-up when the output transis-
tor is saturated. For fixed voltage devices the top of the
internal resistor divider that sets the output voltage is
connected to this pin.
COMP (Pin 8):
A compensation network is inserted
between the V
OUT
and COMP pins to obtain optimal
transient response. Under normal condition, the DC volt-
age of the COMP pin sits at one V
BE
above ground.
FB
(Pin 1):
The feedback pin is the inverting input of the
error amplifier. The noninverting input of the error ampli-
fier is internally connected to a 1.265V reference. The error
amplifier will servo the drive to the output transistor, Q
OUT
in Figure 1, to force the voltage at the feedback pin to be
1.265V. Output voltage is set by a resistor divider as
shown in Figure 1. For adjustable devices an external
resistor divider is used to set the output voltage. For fixed
voltage devices the resistor divider is internal and the top
of the resistor divider is connected to the V
OUT
pin.
LATCH (Pin 2):
The LT1573 provides overcurrent protec-
tion with a timed latch-off circuit. The latch-off time out is
triggered when the DRIVE pin is pulled below the satura-
tion voltage of the drive transistor. The saturation voltage
is a function of the drive current and is equal to approxi-
mately 130mV at 20mA rising to 780mV at 250mA (see
typical performance curves). The time out is set by the
latch charging current and the value of a capacitor con-
nected between the LATCH pin and ground. If the
overcurrent condition persists at the end of the timing
cycle the regulator will latch off until either the latch is reset
or power is cycled off and back on. The latch can be reset
by either pulling the SHDN pin high, pulling current out of
the LATCH pin greater than latching current or grounding
the LATCH pin. Exceeding the thermal limit temperature
will trigger the latch with no timing delay. Under normal
condition, the DC voltage at the LATCH pin is zero. When
the system is latched off, the DC voltage at theLATCH pin
is two V
BE
above ground.
SHDN (Pin 3):
The SHDN pin has two functions. It can be
used to turn off the output voltage by disabling the drive to
the output transistor. It can also be used to reset the
current limit latch. The shutdown/reset functions are
PIU
相关PDF资料 |
PDF描述 |
|---|---|
| LT1573CS8 | Low Dropout PNP Regulator Driver |
| LT1573CS8-2.5 | Low Dropout PNP Regulator Driver |
| LT1573CS8-2.8 | Low Dropout PNP Regulator Driver |
| LT1573CS8-3.3 | Low Dropout PNP Regulator Driver |
| LT1573I | Low Dropout PNP Regulator Driver |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1573CS8 | 功能描述:IC REG CTRLR SGL POS ADJ 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性晶体管驱动器 系列:- 产品培训模块:More Information on LDOs 标准包装:2,500 系列:- 类型:正，固定式 输出数:2 输出电压:2.8V，3.3V 电流 - 电源:12mA 输入电压:5 V ~ 22 V 工作温度:0°C ~ 70°C 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
| LT1573CS8#PBF | 功能描述:IC REG CTRLR SGL POS ADJ 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性晶体管驱动器 系列:- 产品培训模块:More Information on LDOs 标准包装:2,500 系列:- 类型:正，固定式 输出数:2 输出电压:2.8V，3.3V 电流 - 电源:12mA 输入电压:5 V ~ 22 V 工作温度:0°C ~ 70°C 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
| LT1573CS8#TR | 功能描述:IC REG CTRLR SGL POS ADJ 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性晶体管驱动器 系列:- 产品培训模块:More Information on LDOs 标准包装:2,500 系列:- 类型:正，固定式 输出数:2 输出电压:2.8V，3.3V 电流 - 电源:12mA 输入电压:5 V ~ 22 V 工作温度:0°C ~ 70°C 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
| LT1573CS8#TRPBF | 功能描述:IC REG CTRLR SGL POS ADJ 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性晶体管驱动器 系列:- 产品培训模块:More Information on LDOs 标准包装:2,500 系列:- 类型:正，固定式 输出数:2 输出电压:2.8V，3.3V 电流 - 电源:12mA 输入电压:5 V ~ 22 V 工作温度:0°C ~ 70°C 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
| LT1573CS8-2.5 | 功能描述:IC REG CTRLR SGL 2.5V 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性晶体管驱动器 系列:- 产品培训模块:More Information on LDOs 标准包装:2,500 系列:- 类型:正，固定式 输出数:2 输出电压:2.8V，3.3V 电流 - 电源:12mA 输入电压:5 V ~ 22 V 工作温度:0°C ~ 70°C 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。