- 您现在的位置：买卖IC网 > PDF目录377707 > LT1573CS8-2.8 (LINEAR TECHNOLOGY CORP) Low Dropout PNP Regulator Driver PDF资料下载
参数资料
| 型号： | LT1573CS8-2.8 |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 基准电压源/电流源 |
| 英文描述： | Low Dropout PNP Regulator Driver |
| 中文描述： | 2.8 V FIXED POSITIVE LDO REGULATOR, PDSO8 |
| 封装： | 0.150 INCH, PLASTIC, SO-8 |
| 文件页数： | 8/16页 |
| 文件大小： | 200K |
| 代理商： | LT1573CS8-2.8 |
8
LT1573
Current Limit
For regulator circuits using the LT1573, current limiting is
achieved by limiting the base drive current to the external
PNP pass transistor. This means that the actual system
current limit will be a function of both the current limit of
the LT1573 and the Beta of the external PNP. Motorola
provides the following Beta information for the D45H11.
The minimum Beta of the D45H11 is 60 when V
CE
= 1V and
I
C
= 2A. The minimum Beta is 40 when V
CE
= 1V and I
C
=
4A. For other PNP transistors, the user should first find out
the Beta information from the external PNP transistor
manufacturer to determine the appropriate LT1573 base
drive current limit. The current limit of the regulator
system then can be achieved by selecting the appropriate
amount of resistance R
D
in Figure 2.
Selecting R
D
Resistor R
D
can be used to limit the available drive current
to the external PNP transistor. In order to select R
D
, the
user should first choose the value of the drive current that
will give the required value of output current and dropout
voltage. For a circuit using the D45H11 as a pass transistor
this can be done using Table 1. For circuits using transis-
tors other than D45H11, the user must characterize the
transistor to determine the drive current requirements for
the specified output current and dropout voltage. In gen-
eral, it is recommended that the user choose the lowest
value of drive current that will satisfy the output current
requirements. This will minimize the stress on circuit
components during overload conditions.
The formula used to determine the resistor R
D
is:
R
D
= (V
IN
– V
BE
– V
DRIVE
)/(I
DRIVE
+ I
RB
)
where,
V
IN
= the minimum input voltage to the circuit
V
BE
= the maximum emitter/base voltage of the PNP
pass transistor
I
DRIVE
= the minimum PNP base current required
I
RB
= the current through R
B
= V
BE
/R
B
V
DRIVE
= the DRIVE pin saturation voltage when the DRIVE
pin current equals (I
DRIVE
+ I
RB
)
(1)
output current with dropout voltage as low as 0.35V. The
gain-bandwidth product f
T
of the D45H11 is typically
40MHz which enables the regulator, composed of this
PNP transistor and the LT1573, to handle the load changes
of several amps in a few hundred nanoseconds with a
minimum amount of output capacitance.
The following sections describe how specifications can be
determined for the basic regulator based on the LT1573
and D45H11 from Motorola. To determine the specifica-
tions for regulators formed by the LT1573 and other PNP
transistors, a similar method can be used.
Dropout Voltage
The dropout voltage of an LT1573-based regulator circuit
is determined by the V
CE
saturation voltage of the discrete
external PNP transistor when it is driven with a base
current equal to the available drive current of the LT1573.
The LT1573 is guaranteed to sink 250mA of base current
(440mA typ). The available drive current of the LT1573 can
be reduced by adding a resistor (R
D
in Figure 2) in series
with the DRIVE pin. Table 1 lists some useful operating
points for the D45H11. These points were empirically
determined using a sampling of devices.
Table 1. D45H11 Dropout Voltage
TYPICAL
DRIVE CURRENT
(mA)
20
20
40
40
60
60
80
100
100
150
200
150
200
250
OUTPUT CURRENT
(A)
1
2
2
3
3
4
4
4
5
5
5
6
6
7
DROPOUT VOLTAGE
(V)
0.20
0.50
0.25
0.50
0.25
0.70
0.45
0.35
0.70
0.40
0.35
0.65
0.45
0.50
APPLICATIOU
W
U
U
相关PDF资料 |
PDF描述 |
|---|---|
| LT1573CS8-3.3 | Low Dropout PNP Regulator Driver |
| LT1573I | Low Dropout PNP Regulator Driver |
| LT1573IS8 | Low Dropout PNP Regulator Driver |
| LT1573 | Low Dropout PNP Regulator Driver(低压差PNP稳压驱动器) |
| LT1575CN8 | CAP ELECT 330UF 25V HC SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1573CS8-3.3 | 功能描述:IC REG CTRLR SGL 3.3V 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性晶体管驱动器 系列:- 产品培训模块:More Information on LDOs 标准包装:2,500 系列:- 类型:正，固定式 输出数:2 输出电压:2.8V，3.3V 电流 - 电源:12mA 输入电压:5 V ~ 22 V 工作温度:0°C ~ 70°C 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
| LT1573CS8-3.3#PBF | 功能描述:IC REG CTRLR SGL 3.3V 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性晶体管驱动器 系列:- 产品培训模块:More Information on LDOs 标准包装:2,500 系列:- 类型:正，固定式 输出数:2 输出电压:2.8V，3.3V 电流 - 电源:12mA 输入电压:5 V ~ 22 V 工作温度:0°C ~ 70°C 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
| LT1573CS8TR | 制造商:Linear Technology 功能描述: |
| LT1573I | 制造商:LINER 制造商全称:Linear Technology 功能描述:Low Dropout PNP Regulator Driver |
| LT1573IS8 | 功能描述:IC REG CTRLR SGL POS ADJ 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性晶体管驱动器 系列:- 产品培训模块:More Information on LDOs 标准包装:2,500 系列:- 类型:正，固定式 输出数:2 输出电压:2.8V，3.3V 电流 - 电源:12mA 输入电压:5 V ~ 22 V 工作温度:0°C ~ 70°C 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。