- 您现在的位置：买卖IC网 > PDF目录377707 > LT1573IS8 (LINEAR TECHNOLOGY CORP) Low Dropout PNP Regulator Driver PDF资料下载
参数资料
| 型号： | LT1573IS8 |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 基准电压源/电流源 |
| 英文描述： | Low Dropout PNP Regulator Driver |
| 中文描述： | 1.27 V-6.8 V ADJUSTABLE POSITIVE LDO REGULATOR, 0.35 V DROPOUT, PDSO8 |
| 封装： | 0.150 INCH, PLASTIC, SO-8 |
| 文件页数： | 11/16页 |
| 文件大小： | 200K |
| 代理商： | LT1573IS8 |
11
LT1573
capabilities of the PC board and its copper traces. Table
3 lists some typical values for the thermal resistance of
the LT1573. Measured values of thermal resistance for
a specific board size with different copper areas are
listed. All measurements were taken in still air on 3/32
"
FR-4 board with 2oz copper. It is possible to achieve
significantly lower values with thinner multilayer boards.
Compensation
In order to improve the transient response to regulator
output load variation, a capacitor in series with a resistor
can be inserted between the V
OUT
and COMP pins. For the
microprocessor power supply regulator system based on
the LT1573 and the PNP transistor D45H11 with 24 1
μ
F
surface mount ceramic capacitors in parallel with one
220
μ
F surface mount tantalum capacitor at the output as
shown in Figure 1, a 100pF capacitor in series with a 1k
resistor is recommended. In theory, the output capacitor
forms the dominant pole of the regulator system. An
internal compensation capacitor forms another pole. The
external compensation capacitor and resistor form a zero
which adds phase margin to the regulator system to
prevent high frequency oscillation. The LT1573 has an
internal pole at approximately 5kHz. An external compen-
sation zero between 10kHz and 100kHz is usually required
to stabilize the regulator. The zero frequency is primarily
determined by the compensation capacitor and can be
roughly calculated by the following equation:
( )
( )
f
kHz
C
pF
C
ZERO
COMP
COMP
=
(
)
≤
≤
40
30
10
100
,
A compensation resistor between 1k and 10k is sug-
gested. A compensation resistor of 5k works for most
cases. In some cases, a greater compensation resistor is
needed to stop oscillation above 1MHz. In some cases, the
output capacitor may have enough equivalent series resis-
tance (ESR) to generate the required zero and the external
compensation zero may not be needed.
Output Capacitor
The LT1573 is designed to be used with an external PNP
transistor with a high gain-bandwidth product f
T
to make
a regulator with a very fast transient response, which can
minimize the size of the output capacitor. For a regulator
made of an LT1573 and a D45H11, only one 10
μ
F surface
mount ceramic capacitor at the output is enough for the
regulator to handle the output load varying up to 5A in a
few hundred nanoseconds interval and to remain stable
with a 30pF capacitor in series with a 7.5k resistor between
the V
OUT
and COMP pins. If tighter voltage regulation is
Table 3. LT1573 Thermal Resistance
COPPER AREA
TOPSIDE*
BACKSIDE
2500mm
2
2500mm
2
1000mm
2
2500mm
2
225mm
2
2500mm
2
*Device is mounted on topside.
THERMAL RESISTANCE
BOARD AREA (JUNCTION-TO-AMBIENT)
2500mm
2
2500mm
2
2500mm
2
80
°
C/W
80
°
C/W
85
°
C/W
We can find out the maximum junction temperature of
the LT1573 during normal load operation after we
calculate the maximum power dissipation of the LT1573
from Eq (2). From the previous design example, the
maximum power dissipation of the LT1573 is 0.2W.
From Table 3, we know the thermal resistance from
junction-to-ambient is around 85
°
C/W. The tempera-
ture difference between junction and ambient is:
(0.25W)(85
°
C/W) = 21.25
°
C
If the maximum ambient temperature is specified at
50
°
C, the maximum junction temperature will be:
T
JMAX
= 50
°
C + 21.25
°
C = 71.25
°
C
The maximum junction temperature must not exceed
the specified 125
°
C for safe continuous regulator op-
eration.
Thermal Limiting
The thermal shutdown temperature of the LT1573 is
approximately 150
°
C. The thermal limit of the LT1573 can
be used to protect both the LT1573 and the external PNP
pass transistor. This is accomplished by thermally cou-
pling the LT1573 to the PNP power transistor by locating
the LT1573 as close to the PNP transistor as possible. In
this case, the power dissipation of the power transistor
must be considered in the LT1573 maximum junction
temperature calculation.
APPLICATIOU
W
U
U
相关PDF资料 |
PDF描述 |
|---|---|
| LT1573 | Low Dropout PNP Regulator Driver(低压差PNP稳压驱动器) |
| LT1575CN8 | CAP ELECT 330UF 25V HC SMD |
| LT1575CS8-1.5 | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
| LT1575CN8-1.5 | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
| LT1575CN8-2.8 | CAP ELECT 47UF 25V HC SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1573IS8#PBF | 功能描述:IC REG CTRLR SGL POS ADJ 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性晶体管驱动器 系列:- 产品培训模块:More Information on LDOs 标准包装:2,500 系列:- 类型:正，固定式 输出数:2 输出电压:2.8V，3.3V 电流 - 电源:12mA 输入电压:5 V ~ 22 V 工作温度:0°C ~ 70°C 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
| LT1573IS8#TR | 功能描述:IC REG CTRLR SGL POS ADJ 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性晶体管驱动器 系列:- 产品培训模块:More Information on LDOs 标准包装:2,500 系列:- 类型:正，固定式 输出数:2 输出电压:2.8V，3.3V 电流 - 电源:12mA 输入电压:5 V ~ 22 V 工作温度:0°C ~ 70°C 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
| LT1573IS8#TRPBF | 功能描述:IC REG CTRLR SGL POS ADJ 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性晶体管驱动器 系列:- 产品培训模块:More Information on LDOs 标准包装:2,500 系列:- 类型:正，固定式 输出数:2 输出电压:2.8V，3.3V 电流 - 电源:12mA 输入电压:5 V ~ 22 V 工作温度:0°C ~ 70°C 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
| LT1575 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Ultrafast Transient Response, Low Dropout Regulators Adjustable and Fixed |
| LT-1575-113-006 | 制造商:Carling Technologies 功能描述:LT-SERIES TOGGLE SWITCH - Bulk |
发布紧急采购，3分钟左右您将得到回复。