- 您现在的位置：买卖IC网 > PDF目录14033 > LT1578IS8#PBF (Linear Technology)IC REG BUCK ADJ 1.5A 8SOIC PDF资料下载
参数资料
| 型号： | LT1578IS8#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 10/28页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 1.5A 8SOIC |
| 标准包装： | 100 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 可调至 1.21V |
| 输入电压： | 4 V ~ 15 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 200kHz |
| 电流 - 输出： | 1.5A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 管件 |
| 供应商设备封装： | 8-SOIC |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LT1578/LT1578-2.5
APPLICATIO N S I N FOR M ATIO N
Note that there is less load current available at the higher
input voltage because inductor ripple current increases.
This is not always the case. Certain combinations of
inductor value and input voltage range may yield lower
available load current at the lowest input voltage due to
reduced peak switch current at high duty cycles. If load
current is close to the maximum available, please check
maximum available current at both input voltage
extremes. To calculate actual peak switch current with a
given set of conditions, use:
physical size of the inductor. Higher values allow more
output current because they reduce peak current seen by
the LT1578 switch, which has a 1.5A limit. Higher values
also reduce output ripple voltage, and reduce core loss.
Graphs in the Typical Performance Characteristics section
show maximum output load current versus inductor size
and input voltage.
When choosing an inductor you might have to consider
maximum load current, core and copper losses, allowable
component height, output voltage ripple, EMI, fault cur-
2 ( )( )( )
L f V
I SW ( PEAK ) = I OUT +
V OUT ( V IN ? V OUT )
IN
rent in the inductor, saturation, and of course, cost. The
following procedure is suggested as a way of handling
these somewhat complicated and conflicting requirements.
1. Choose a value in microhenries from the graphs of
For lighter loads where discontinuous operation can be
used, maximum load current is equal to:
maximum load current and core loss. Choosing a small
inductor may result in discontinuous mode operation
at lighter loads, but the LT1578 is designed to work
( I P ) ( )( )( V IN )
I OUT(MAX) =
Discontinuous mode
2
f L
2 ( V OUT ) ( V IN ? V OUT )
well in either mode. Keep in mind that lower core loss
means higher cost, at least for closed core geometries
like toroids.
Assume that the average inductor current is equal to
Example: with L = 5 μ H, V OUT = 5V, and V IN(MAX ) = 15V,
load current and decide whether or not the inductor
must withstand continuous fault conditions. If maxi-
( 1 . 5 ) ?? 200 ? 10 ? 3 ? ?? 5 ? 10 ? 6 ?? ( 15 )
I OUT ( MAX ) =
2
2 ( 5 ) ( 15 ? 5 )
= 0 . 34 A
mum load current is 0.5A, for instance, a 0.5A inductor
may not survive a continuous 1.5A overload condition.
Dead shorts will actually be more gentle on the induc-
tor because the LT1578 has foldback current limiting.
The main reason for using such a tiny inductor is that it is
physically very small, but keep in mind that peak-to-peak
inductor current will be very high. This will increase output
ripple voltage. If the output capacitor has to be made larger
to reduce ripple voltage, the overall circuit could actually
wind up larger.
CHOOSING THE INDUCTOR AND OUTPUT CAPACITOR
For most applications the output inductor will fall in the
range of 15 μ H to 60 μ H. Lower values are chosen to reduce
10
2. Calculate peak inductor current at full load current to
ensure that the inductor will not saturate. Peak current
can be significantly higher than output current, espe-
cially with smaller inductors and lighter loads, so don’t
omit this step. Powdered iron cores are forgiving
because they saturate softly, whereas ferrite cores
saturate abruptly. Other core materials fall somewhere
in between. The following formula assumes continu-
ous mode of operation, but it errs only slightly on the
high side for discontinuous mode, so it can be used for
all conditions.
相关PDF资料 |
PDF描述 |
|---|---|
| V24C28C150BF3 | CONVERTER MOD DC/DC 28V 150W |
| LT1578IS8 | IC REG BUCK ADJ 1.5A 8SOIC |
| LT1576IS8-5SYNC | IC REG BUCK 5V 1.5A 8SOIC |
| LT1576IS8-5#PBF | IC REG BUCK 5V 1.5A 8SOIC |
| LT1576IS8-5 | IC REG BUCK 5V 1.5A 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1579 | 制造商:LINER 制造商全称:Linear Technology 功能描述:300mA Dual Input Smart Battery Backup Regulator |
| LT1579-3 | 制造商:LINER 制造商全称:Linear Technology 功能描述:300mA Dual Input Smart Battery Backup Regulator |
| LT1579CGN | 功能描述:IC LDO REG SMART DUAL ADJ 16SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:2,000 系列:Impedance Track™ 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.4 V ~ 2.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:20-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:20-TSSOP 包装:带卷 (TR) 产品目录页面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名称:296-21665-2 |
| LT1579CGN#PBF | 功能描述:IC LDO REG SMART DUAL ADJ 16SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:2,000 系列:Impedance Track™ 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.4 V ~ 2.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:20-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:20-TSSOP 包装:带卷 (TR) 产品目录页面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名称:296-21665-2 |
| LT1579CGN#TR | 功能描述:IC REG LDO SMART DUAL ADJ 16SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。