- 您现在的位置：买卖IC网 > PDF目录16226 > LT1579CGN-3 (Linear Technology)IC LDO REG SMART DUAL 3V 16SSOP PDF资料下载
参数资料
| 型号： | LT1579CGN-3 |
| 厂商： | Linear Technology |
| 文件页数： | 12/20页 |
| 文件大小： | 0K |
| 描述： | IC LDO REG SMART DUAL 3V 16SSOP |
| 标准包装： | 100 |
| 功能： | 备份管理 |
| 电池化学： | 智能电池 |
| 工作温度： | 0°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SSOP |
| 包装： | 管件 |
| 产品目录页面： | 1328 (CN2011-ZH PDF) |
LT1579
APPLICATIO N S I N FOR M ATIO N
? – ( I ADJ )( R 2 )
V OUT = 1 . 5 V ? 1 +
Device Overview
The LT1579 is a dual input, single output, low dropout
linear regulator. The device is designed to provide an
uninterruptible output voltage from two independent input
voltage sources on a priority basis. All of the circuitry
needed to switch smoothly and automatically between
inputs is incorporated in the device. All power supplied to
the load is drawn from the primary input (V IN1 ) until the
device senses that the primary input is failing. At this point
the LT1579 smoothly switches from the primary input to
the secondary input (V IN2 ) to maintain output regulation.
The device is capable of providing 300mA from either
input at a dropout voltage of 0.4V. Total quiescent current
when operating from the primary input is 50 μ A, which is
45 μ A from the primary input, 2 μ A from the secondary and
a minimum input current of 3 μ A which will be drawn from
the higher of the two input voltages.
A single error amplifier controls both output stages so
regulation remains tight regardless of which input is
providing power. Threshold levels for the error amplifier
and low-battery detectors are set by the internal 1.5V
reference. Output voltage is set by an internal resistor
divider for fixed voltage parts and an external divider for
adjustable parts. Internal bias circuitry powers the refer-
ence, error amplifier, output driver controls, logic flags
and low-battery comparators.
The LT1579 aids power management with the use of two
independent low-battery comparators and two status flags.
The low-battery comparators can be used to monitor the
input voltage levels. The BACKUP flag signals when any
power is being drawn from the secondary input and the
DROPOUT flag provides indication that both input volt-
ages are critically low and the output is unregulated.
Additionally, the switch to the secondary input from the
primary can be forced externally through the use of the
currents and logic functions. In shutdown, quiescent
currents are 2 μ A from the primary input, 2 μ A from the
secondary input and an additional 3 μ A which is drawn
from the higher of the two input voltages.
Adjustable Operation
The adjustable version of the LT1579 has an output
voltage range of 1.5V to 20V. The output voltage is set by
the ratio of two external resistors as shown in Figure 1. The
device servos the output to maintain the voltage at the
adjust pin at 1.5V. The current in R1 is then equal to 1.5V/
R1 and the current in R2 is the current in R1 minus the
adjust pin bias current. The adjust pin bias current, 6nA at
25 ° C, flows out of the adjust pin through R1 to ground. The
output voltage can now be calculated using the formula:
? R 2 ?
? R 1 ?
The value of R1 should be less than 500k to minimize the
error in the output voltage caused by adjust pin bias
current. With 500k resistors for both R1 and R2, the error
induced by adjust pin bias current at 25 ° C is 3mV or 0.1%
of the total output voltage. With appropriate value and
tolerance resistors, the error due to adjust pin bias current
may often be ignored. Note that in shutdown, the output is
turned off and the divider current is zero. The parallel
combination of R1 and R2 should be greater than 20k to
allow the error amplifier to start. In applications where the
minimum parallel resistance requirement cannot be met,
a 20k resistor may be placed in series with the adjust pin.
This introduces an error in the reference point for the
resistor divider equal to (I ADJ )(20k).
secondary select pin (SS). This active low logic pin, when
pulled below the threshold, will cause power draw to
switch from the primary input to the secondary input.
OUT
ADJ
R2
C FB
+
V OUT
C OUT
Current flowing in the primary input is reduced to only a
few microamperes, while all power draw (load current and
bias currents) switches to the secondary. The LT1579 has
GND
R1
1579 ? F01
a low power shutdown state which shuts off all bias
12
Figure 1. Adjustable Operation
相关PDF资料 |
PDF描述 |
|---|---|
| LT1579CGN#PBF | IC LDO REG SMART DUAL ADJ 16SSOP |
| H3BWH-6436G | IDC CABLE - HSR64H/AE64G/HPL64H |
| LT1579CGN | IC LDO REG SMART DUAL ADJ 16SSOP |
| M1DXA-5040K | IDC CABLE - MKR50A/MC50F/X |
| LT1512CGN | IC BATT CHRGR CONST I/V 16-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1579CGN-3#PBF | 功能描述:IC LDO REG SMART DUAL 3V 16SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
| LT1579CGN-3#TR | 功能描述:IC REG LDO SMART DUAL 3V 16SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LT1579CGN-3#TRPBF | 功能描述:IC LDO REG SMART DUAL 3V 16SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
| LT1579CGN-3.3 | 功能描述:IC LDO REG SMART DUAL3.3V 16SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LT1579CGN-3.3#PBF | 功能描述:IC LDO REG SMART DUAL3.3V 16SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。