- 您现在的位置：买卖IC网 > PDF目录14192 > LT1615ES5#TRM (Linear Technology)IC REG BOOST ADJ 0.35A TSOT23-5 PDF资料下载
参数资料
| 型号： | LT1615ES5#TRM |
| 厂商： | Linear Technology |
| 文件页数： | 5/8页 |
| 文件大小： | 0K |
| 描述： | IC REG BOOST ADJ 0.35A TSOT23-5 |
| 标准包装： | 1 |
| 类型： | 升压（升压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.23 V ~ 36 V |
| 输入电压： | 1.2 V ~ 15 V |
| 电流 - 输出： | 350mA |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-5 细型，TSOT-23-5 |
| 包装： | 剪切带 (CT) |
| 供应商设备封装： | TSOT-23-5 |
| 其它名称： | LT1615ES5 LT1615ES5#TRMCT LT1615ES5-ND |
LT1615/LT1615-1
APPLICATIO S I FOR ATIO
Choosing an Inductor
Several recommended inductors that work well with the
LT1615 and LT1615-1 are listed in Table 1, although there
are many other manufacturers and devices that can be
used. Consult each manufacturer for more detailed infor-
mation and for their entire selection of related parts. Many
different sizes and shapes are available. Use the equations
and recommendations in the next few sections to find the
correct inductance value for your design.
Table 1. Recommended Inductors
PART VALUE ( μ H) MAX DCR ( ? ) VENDOR
V IN value in the above equation. For most systems with
output voltages below 7V, a 4.7 μ H inductor is the best
choice, even though the equation above might specify a
smaller value. This is due to the inductor current over-
shoot that occurs when very small inductor values are
used (see Current Limit Overshoot section).
For higher output voltages, the formula above will give
large inductance values. For a 2V to 20V converter (typical
LCD Bias application), a 21 μ H inductor is called for with
the above equation, but a 10 μ H inductor could be used
without excessive reduction in maximum output current.
LQH3C4R7
LQH3C100
LQH3C220
CD43-4R7
CD43-100
CDRH4D18-4R7
CDRH4D18-100
4.7
10
22
4.7
10
4.7
10
0.26
0.30
0.92
0.11
0.18
0.16
0.20
Murata
(814) 237-1431
www.murata.com
Sumida
(847) 956-0666
www.sumida.com
Inductor Selection—SEPIC Regulator
The formula below calculates the approximate inductor
value to be used for a SEPIC regulator using the LT1615.
As for the boost inductor selection, a larger or smaller
value can be used.
L = 2 ? OUT D
? t OFF
DO1608-472
DO1608-103
DO1608-223
4.7
10
22
0.09
0.16
0.37
Coilcraft
(847) 639-6400
www.coilcraft.com
? V + V
? I LIM
?
?
Inductor Selection—Boost Regulator
I PEAK LIM + ?
? V IN ( MAX ) ? V SAT ?
? 100 ns
The formula below calculates the appropriate inductor
value to be used for a boost regulator using the LT1615 or
LT1615-1 (or at least provides a good starting point). This
value provides a good tradeoff in inductor size and system
performance. Pick a standard inductor close to this value.
A larger value can be used to slightly increase the available
output current, but limit it to around twice the value
calculated below, as too large of an inductance will in-
crease the output voltage ripple without providing much
additional output current. A smaller value can be used
(especially for systems with output voltages greater than
12V) to give a smaller physical size. Inductance can be
calculated as:
Current Limit Overshoot
For the constant off-time control scheme of the LT1615,
the power switch is turned off only after the 350mA (or
100mA) current limit is reached. There is a 100ns delay
between the time when the current limit is reached and
when the switch actually turns off. During this delay, the
inductor current exceeds the current limit by a small
amount. The peak inductor current can be calculated by:
= I
? L ?
Where V SAT = 0.25V (switch saturation voltage). The
V OUT ? V IN ( ) + V D
L =
MIN
I LIM
t OFF
current overshoot will be most evident for systems with
high input voltages and for systems where smaller induc-
tor values are used. This overshoot can be beneficial as it
helps increase the amount of available output current for
where V D = 0.4V (Schottky diode voltage), I LIM = 350mA or
100mA, and t OFF = 400ns; for designs with varying V IN
such as battery powered applications, use the minimum
smaller inductor values. This will be the peak current seen
by the inductor (and the diode) during normal operation.
For designs using small inductance values (especially at
sn16151 16151fas
5
相关PDF资料 |
PDF描述 |
|---|---|
| VI-B1F-EW-F2 | CONVERTER MOD DC/DC 72V 100W |
| GSC22DRAH | CONN EDGECARD 44POS R/A .100 SLD |
| VI-B1D-EX-F4 | CONVERTER MOD DC/DC 85V 75W |
| GMC22DRAH | CONN EDGECARD 44POS R/A .100 SLD |
| VI-B1D-EX-F1 | CONVERTER MOD DC/DC 85V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1615ES5TRMPBF | 制造商:Linear Technology 功能描述:DC/DC Step Up Converter LT1615ES5 |
| LT1615IS5 | 制造商:Linear Technology 功能描述:Conv DC-DC Single Step Up 1.2V to 15V 5-Pin TSOT-23 |
| LT1615IS5#PBF | 制造商:Linear Technology 功能描述:Conv DC-DC Single Step Up 1.2V to 15V 5-Pin TSOT-23 Bulk 制造商:Linear Technology 功能描述:DC-DC CONVERTER BOOST SOT-23 制造商:Linear Technology 功能描述:DC-DC CONVERTER, BOOST, SOT-23-5; Primary Input Voltage:15V; No. of Outputs:1; Output Current:350mA; No. of Pins:5; Operating Temperature Min:-40C; Operating Temperature Max:85C; Package / Case:5-SOT-23; Supply Voltage Max:15V ;RoHS Compliant: Yes |
| LT1615IS5#TR | 功能描述:IC REG BOOST ADJ 0.35A TSOT23-5 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LT1615IS5#TRM | 功能描述:IC REG BOOST ADJ 0.35A TSOT23-5 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
发布紧急采购，3分钟左右您将得到回复。