- 您现在的位置：买卖IC网 > PDF目录19894 > LT1641IS8 (Linear Technology)IC CONTRLR HOTSWAP POSVOLT 8SOIC PDF资料下载
参数资料
| 型号： | LT1641IS8 |
| 厂商： | Linear Technology |
| 文件页数： | 5/12页 |
| 文件大小： | 192K |
| 描述： | IC CONTRLR HOTSWAP POSVOLT 8SOIC |
| 标准包装： | 100 |
| 类型： | 热交换控制器 |
| 应用： | 通用 |
| 内部开关： | 无 |
| 电源电压： | 9 V ~ 80 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 管件 |
| 其它名称： | Q1140670 |
5
LT1641
1641fd
PI FU CTIO S
U
U
ON (Pin 1): The ON pin is used to implement undervoltage
lockout. When the ON pin is pulled below the 1.233V High-
to-Low threshold voltage, an undervoltage condition is
detected and the GATE pin is pulled low to turn the
MOSFET off. When the ON pin rises above the 1.313V
Low-to-High threshold voltage, the MOSFET is turned on
again.
FB (Pin 2): Power Good Comparator Input. It monitors the
output voltage with an external resistive divider. When the
voltage on the FB pin is lower than the High-to-Low
threshold of 1.233V, the PWRGD pin is pulled low and
released when the FB pin is pulled above the 1.313V Low-
to-High threshold.
The FB pin also effects foldback current limit (see Figure 7
and related discussion).
PWRGD (Pin 3): Open Collector Output to GND. The
PWRGD pin is pulled low whenever the voltage at the FB
pin falls below the High-to-Low threshold voltage. It goes
into a high impedance state when the voltage on the FB pin
exceeds the Low-to-High threshold voltage. An external
pull-up resistor can pull the pin to a voltage higher or lower
than V
CC
.
GND (Pin 4): Chip Ground.
TIMER (Pin 5): Timing Input. An external timing capacitor
at this pin programs the maximum time the part is allowed
to remain in current limit.
When the part goes into current limit, an 80礎 pull-up
current source starts to charge the timing capacitor. When
the voltage on the TIMER pin reaches 1.233V, the GATE
pin is pulled low; the pull-up current will be turned off and
the capacitor is discharged by a 3礎 pull-down current.
When the TIMER pin falls below 0.5V, the GATE pin turns
on once the ON pin is pulsed low. Use no less than 1.5nF
for the timing capacitor, C2.
By connecting a 0.01礔 capacitor from the GATE pin to the
center tap of a resistive divider at the ON pin, the part
automatically restarts after a current limit fault. With a
short at the output, the part cycles on and off with a 3.75%
on-time duty cycle.
GATE (Pin 6): The High Side Gate Drive for the External
N-Channel. An internal charge pump guarantees at least
10V of gate drive for supply voltages above 20V and 4.5V
gate drive for supply voltages between 10.8V and 20V. The
rising slope of the voltage at the GATE is set by an external
capacitor connected from the GATE pin to GND and an
internal 10礎 pull-up current source from the charge
pump output.
When the current limit is reached, the GATE pin voltage will
be adjusted to maintain a constant voltage across the
sense resistor while the timer capacitor starts to charge.
If the TIMER pin voltage exceeds 1.233V, the GATE pin will
be pulled low.
The GATE pin is pulled to GND whenever the ON pin is
pulled low, the V
CC
supply voltage drops below the 8.3V
undervoltage lockout threshold or the TIMER pin rises
above 1.233V.
SENSE (Pin 7): The Current Limit Sense Pin. A sense
resistor must be placed in the supply path between V
CC
and SENSE. The current limit circuit will regulate the
voltage across the sense resistor (V
CC
V
SENSE
) to 47mV
when V
FB
is 0.5V or higher. If V
FB
drops below 0.5V, the
voltage across the sense resistor decreases linearly and
stops at 12mV when V
FB
is 0V.
To defeat current limit, short the SENSE pin to the V
CC
pin.
V
CC
(Pin 8): The Positive Supply Input ranges from 9V to
80V for normal operation. I
CC
is typically 2mA. An internal
undervoltage lockout circuit disables the chip for inputs
less than 8.3V.
相关PDF资料 |
PDF描述 |
|---|---|
| EGM08DRSN-S288 | CONN EDGECARD 16POS .156 EXTEND |
| AMC22DRTH-S13 | CONN EDGECARD 44POS .100 EXTEND |
| THJD335K050RJN | CAP TANT 3.3UF 50V 10% 2917 |
| LTC4212CMS | IC CTRLR HOTSWAP TIMEOUT 10MSOP |
| AT17LV65A-10JC | IC SRL CONFIG EEPROM 64K 20-PLCC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1641IS8#PBF | 功能描述:IC CONTRLR HOTSWAP POSVOLT 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| LT1641IS8#TR | 功能描述:IC CTRLR HOTSWAP POS VOLT 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| LT1641IS8#TRPBF | 功能描述:IC CONTRLR HOTSWAP POSVOLT 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| LT1671 | 制造商:LINER 制造商全称:Linear Technology 功能描述:60ns, Low Power, Single Supply, Ground-Sensing Comparator |
| LT1671CMS8 | 功能描述:IC COMPARATOR 60NS LOW PWR 8MSOP RoHS:否 类别:集成电路 (IC) >> 线性 - 比较器 系列:- 标准包装:25 系列:- 类型:带电压基准 元件数:4 输出类型:CMOS，开路漏极，TTL 电压 - 电源，单路/双路(±):2 V ~ 11 V，±1 V ~ 5.5 V 电压 - 输入偏移（最小值）:10mV @ 5V 电流 - 输入偏压（最小值）:- 电流 - 输出（标准）:0.015mA @ 5V 电流 - 静态（最大值）:8.5µA CMRR, PSRR（标准）:80dB CMRR，80dB PSRR 传输延迟（最大）:12µs 磁滞:50mV 工作温度:0°C ~ 70°C 封装/外壳:16-DIP（0.300"，7.62mm） 安装类型:通孔 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。