- 您现在的位置：买卖IC网 > PDF目录10697 > LT1719IS6#TRM (Linear Technology)IC COMP R-RINOUT SINGLE SOT23-6 PDF资料下载
参数资料
| 型号： | LT1719IS6#TRM |
| 厂商： | Linear Technology |
| 文件页数： | 3/22页 |
| 文件大小： | 0K |
| 描述： | IC COMP R-RINOUT SINGLE SOT23-6 |
| 标准包装： | 1 |
| 系列： | UltraFast™ |
| 类型： | 通用 |
| 元件数： | 1 |
| 输出类型： | CMOS，满摆幅，TTL |
| 电压 - 电源，单路/双路(±)： | 2.7 V ~ 6 V |
| 电压 - 输入偏移（最小值）： | 2.5mV @ 5V |
| 电流 - 输入偏压（最小值）： | 6µA @ 5V |
| 电流 - 输出（标准）： | 20mA |
| 电流 - 静态（最大值）： | 9mA |
| CMRR, PSRR（标准）： | 65dB CMRR，80dB PSRR |
| 传输延迟（最大）： | 13ns |
| 磁滞： | 7mV |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | SOT-23-6 |
| 安装类型： | 表面贴装 |
| 包装： | 剪切带 (CT) |
| 其它名称： | LT1719IS6 LT1719IS6#TRMCT LT1719IS6-ND |
LT1719
11
1719fa
APPLICATIONS INFORMATION
The outputs of the LT1719 are capable of very high slew
rates. To prevent overshoot, ringing and other problems
with transmission line effects, keep the output traces
shorter than 10cm, or be sure to terminate the lines
to maintain signal integrity. The LT1719 can drive DC
terminations of 200Ω or more, but lower characteristic
impedance traces can be used with series termination or
AC termination topologies.
Shutdown Control
The LT1719 features a shutdown control pin for reduced
quiescent current when the comparator is not needed.
During shutdown, the inputs and the outputs become high
impedances. The LT1719 is enabled when the shutdown
input is pulled low with a threshold roughly two diode drops
below + VS or V+. Therefore, if driven by a standard TTL
gate, a pull-up resistor should be used. Because shutdown
is active high, this resistor adds little power drain during
shutdown. A logic high disables the comparator. The
LT1719S8 logic interface is based on the output power
rails, +VS and GND.
For applications that do not use the shutdown feature,
it may be helpful to tie the shutdown control to ground
through a 100Ω resistor rather than directly. This allows
the SHDN pin to be pulled high during debug or in-circuit
test (bed of nails) so that the output node can be wiggled
without damaging the low impedance output driver of
the LT1719.
The shutdown state is not guaranteed to be useful as a
multiplexer. Digital signals can have extremely fast edge
rates that may be enough to momentarily activate the
LT1719 output stage via internal capacitive coupling. No
damage to the LT1719 will result, but this could prove
deleterious to the intended recipient of the signal.
The LT1719 includes a FET pull-up on the shutdown control
pin (see the Simplied Schematic) as well as other inter-
nal structures to make the shutdown state current drain
<<1μA. Shutdown is guaranteed with an open circuit on the
shutdown control pin. When the shutdown control pin is
driven to +VS/V+ – 0.5V, the 70kΩ linear region impedance
of the pull-up FET will cause a current ow of 7μA (typ)
into the +VS/V+ pin and out the shutdown pin. Currents in
all other power supply terminals will be <1μA.
Power Supply Sequencing
The LT1719S8 is designed to tolerate any power supply
sequencing at system turn-on and power down. In any
of the previously shown power supply congurations, the
various supplies can activate in any order without exces-
sive current drain by the LT1719.
As always, the Absolute Maximum Ratings must not be
exceeded, either on the power supply terminals or the input
terminals. Power supply sequencing problems can occur
when input signals are powered from supplies that are
independent of the LT1719’s supplies. For the compara-
tor inputs, the signals should be powered from the same
VCC and VEE supplies as the LT1719. For the shutdown
input, the signal should be powered from the same +VS
as the LT1719.
Hysteresis
The LT1719 includes internal hysteresis, which makes it
easier to use than many other similar speed comparators.
The input-output transfer characteristic is illustrated in
Figure 3 showing the denitions of VOS and VHYST based
upon the two measurable trip points. The hysteresis band
makes the LT1719 well behaved, even with slowly moving
inputs.
Figure 3. Hysteresis I/O Characteristics
VHYST
(= VTRIP
+ – VTRIP–)
VHYST/2
VOL
1719 F03
VOH
VTRIP
–
VTRIP
+
ΔVIN = VIN
+ – VIN–
VTRIP
+ + VTRIP–
2
VOS =
V
OUT
0
相关PDF资料 |
PDF描述 |
|---|---|
| VI-JWW-MY-F3 | CONVERTER MOD DC/DC 5.5V 50W |
| VI-JWW-MY-F2 | CONVERTER MOD DC/DC 5.5V 50W |
| LTC1843IS8 | IC COMP ULTLOPWR W/REF DUAL8SOIC |
| VI-JWW-MY-F1 | CONVERTER MOD DC/DC 5.5V 50W |
| LTC1842IS8 | IC COMP ULTLOPWR W/REF DUAL8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1719IS8 | 功能描述:IC COMP R-R SINGLE 4.5NS 8SOIC RoHS:否 类别:集成电路 (IC) >> 线性 - 比较器 系列:UltraFast™ 标准包装:25 系列:- 类型:带电压基准 元件数:4 输出类型:CMOS，开路漏极，TTL 电压 - 电源，单路/双路(±):2 V ~ 11 V，±1 V ~ 5.5 V 电压 - 输入偏移（最小值）:10mV @ 5V 电流 - 输入偏压（最小值）:- 电流 - 输出（标准）:0.015mA @ 5V 电流 - 静态（最大值）:8.5µA CMRR, PSRR（标准）:80dB CMRR，80dB PSRR 传输延迟（最大）:12µs 磁滞:50mV 工作温度:0°C ~ 70°C 封装/外壳:16-DIP（0.300"，7.62mm） 安装类型:通孔 包装:管件 |
| LT1719IS8#PBF | 功能描述:IC COMP R-RINOUT SINGLE 8-SOIC RoHS:是 类别:集成电路 (IC) >> 线性 - 比较器 系列:UltraFast™ 标准包装:1 系列:- 类型:通用 元件数:1 输出类型:CMOS，开路集电极，TTL 电压 - 电源，单路/双路(±):2.7 V ~ 5.5 V 电压 - 输入偏移（最小值）:7mV @ 5V 电流 - 输入偏压（最小值）:0.25µA @ 5V 电流 - 输出（标准）:84mA @ 5V 电流 - 静态（最大值）:120µA CMRR, PSRR（标准）:- 传输延迟（最大）:600ns 磁滞:- 工作温度:-40°C ~ 85°C 封装/外壳:SC-74A，SOT-753 安装类型:表面贴装 包装:剪切带 (CT) 产品目录页面:1268 (CN2011-ZH PDF) 其它名称:*LMV331M5*LMV331M5/NOPBLMV331M5CT |
| LT1719IS8#PBF | 制造商:Linear Technology 功能描述:ICVOLT COMPARATORSINGLEBIPO 制造商:Linear Technology 功能描述:IC,VOLT COMPARATOR,SINGLE,BIPOLAR,SOP,8P |
| LT1719IS8#TR | 功能描述:IC COMP R-R SINGLE 4.5NS 8SOIC RoHS:否 类别:集成电路 (IC) >> 线性 - 比较器 系列:UltraFast™ 标准包装:25 系列:- 类型:带电压基准 元件数:4 输出类型:CMOS，开路漏极，TTL 电压 - 电源，单路/双路(±):2 V ~ 11 V，±1 V ~ 5.5 V 电压 - 输入偏移（最小值）:10mV @ 5V 电流 - 输入偏压（最小值）:- 电流 - 输出（标准）:0.015mA @ 5V 电流 - 静态（最大值）:8.5µA CMRR, PSRR（标准）:80dB CMRR，80dB PSRR 传输延迟（最大）:12µs 磁滞:50mV 工作温度:0°C ~ 70°C 封装/外壳:16-DIP（0.300"，7.62mm） 安装类型:通孔 包装:管件 |
| LT1719IS8#TRPBF | 功能描述:IC COMP R-RINOUT SINGLE 8-SOIC RoHS:是 类别:集成电路 (IC) >> 线性 - 比较器 系列:UltraFast™ 标准包装:25 系列:- 类型:带电压基准 元件数:4 输出类型:CMOS，开路漏极，TTL 电压 - 电源，单路/双路(±):2 V ~ 11 V，±1 V ~ 5.5 V 电压 - 输入偏移（最小值）:10mV @ 5V 电流 - 输入偏压（最小值）:- 电流 - 输出（标准）:0.015mA @ 5V 电流 - 静态（最大值）:8.5µA CMRR, PSRR（标准）:80dB CMRR，80dB PSRR 传输延迟（最大）:12µs 磁滞:50mV 工作温度:0°C ~ 70°C 封装/外壳:16-DIP（0.300"，7.62mm） 安装类型:通孔 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。