- 您现在的位置：买卖IC网 > PDF目录377712 > LT1722 (Linear Technology Corporation) Single, Dual, Quad 200MHz Low Noise Precision Op Amps PDF资料下载
参数资料
| 型号： | LT1722 |
| 厂商： | Linear Technology Corporation |
| 英文描述： | Single, Dual, Quad 200MHz Low Noise Precision Op Amps |
| 中文描述： | 单，双，四200MHz的低噪声精密运算放大器 |
| 文件页数： | 12/16页 |
| 文件大小： | 326K |
| 代理商： | LT1722 |
LT1722/LT1723/LT1724
12
172234fa
APPLICATIU
W
U
U
The LT1722/LT1723/LT1724 may be inserted directly into
many operational amplifier applications improving both
DC and AC performance, as well as noise and distortion.
Layout and Passive Components
The LT1722/LT1723/LT1724 amplifiers are more tolerant
of less than ideal layouts than other high speed amplifiers.
For maximum performance (for example, fast settling
time) use a ground plane, short lead lengths and RF quality
bypass capacitors (0.01
μ
F to 0.1
μ
F). For high drive cur-
rent applications, use low ESR supply bypass capacitors
(1
μ
F to 10
μ
F tantalum). The output/input parasitic cou-
pling should be minimized when high frequency perfor-
mance is required.
The parallel combination of the feedback resistor and gain
setting resistor on the inverting input combine with the
input capacitance to form a pole that can cause peaking or
even oscillations. In parallel with the feedback resistor, a
capacitor of value:
C
F
> R
G
C
IN
/R
F
should be used to cancel the input pole and optimize
dynamic performance. For unity-gain applications where
a feedback resistor is used, such as an I-to-V converter, C
F
should be five times greater than C
IN
; an optimum value for
C
F
is 10pF.
Input Considerations
Each of the LT1722/LT1723/LT1724 inputs is protected
with back-to-back diodes across the bases of the NPN
input devices. If greater than 0.7V differential input volt-
ages are anticipated, the input current must be limited to
less than 10mA with an external series resistor. Each input
also has two ESD clamp diodes—one to each supply. If an
input is driven beyond the supply, limit the current with an
external resistor to less than 10mA. The input stage
protection circuit is shown in Figure 1.
The input currents of the LT1722/LT1723/LT1724 are
typically in the tens of nA range due to the bias current
cancellation technique used at the input. As the input
offset current can be greater than either input current,
D1
D3
+IN
+IN
D4
D5
D6
1723 F01
D2
R
I
1
I
2
Q1
R
EXT
Q2
V
S+
V
S–
–IN
–IN
R
EXT
Figure 1. Input Stage Protection
adding resistance to balance source resistance is not
recommended. The value of the source resistor should be
below 12k as it actually degrades DC accuracy and also
increases noise.
Total Input Noise
The total input noise of the LT1722/LT1723/LT1724 is
optimized for a source resistance between 0.8k and 12k.
Within this range, the total input noise is dominated by the
noise of the source resistance itself. When the source
resistance is below 0.8k, voltage noise of the amplifier
dominates. When the source resistance is above 12k, the
input noise current is the dominant contributor.
Capacitive Loading
The
LT1722/LT1723/LT1724
drive capacitive loads up to
100pF with unity gain. As the capacitive load increases,
both the bandwidth and the phase margin decrease
causing peaking in the frequency response and overshoot
in the transient response. When there is a need to drive a
larger capacitive load, a 25
series resistance assures
stability with any value of load capacitor. A feedback
capacitor also helps to reduce any peaking.
Power Dissipation
The LT1722/LT1723/LT1724 combine high speed and
large output drive in a small package. Maximum junction
temperature (T
J
) is calculated from the ambient tempera-
ture (T
A
), power dissipation per amplifier (P
D
) and number
of amplifiers (n) as follows:
T
J
= T
A
+ (n P
D
θ
JA
)
相关PDF资料 |
PDF描述 |
|---|---|
| LT1723CMS8 | Single, Dual, Quad 200MHz Low Noise Precision Op Amps |
| LT1723CS8 | Single, Dual, Quad 200MHz Low Noise Precision Op Amps |
| LT1723IMS8 | Single, Dual, Quad 200MHz Low Noise Precision Op Amps |
| LT1723IS8 | Single, Dual, Quad 200MHz Low Noise Precision Op Amps |
| LT1724CS | Single, Dual, Quad 200MHz Low Noise Precision Op Amps |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1722CS5 | 制造商:Linear Technology 功能描述:OP Amp Single GP ±6.3V/12.6V 5-Pin TSOT-23 |
| LT1722CS5#PBF | 制造商:Linear Technology 功能描述:OP Amp Single GP 制造商:Linear Technology 功能描述:SC-Amps/Industrial Cut Tape 2 制造商:Linear Technology 功能描述:SC-Amps/Industrial, Cut Tape 200MHz Low Noise Precision OP Amp |
| LT1722CS5#TR | 功能描述:IC OPAMP PREC 200MHZ TSOT-23-5 RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:160 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:10 V/µs 增益带宽积:9MHz -3db带宽:- 电流 - 输入偏压:1pA 电压 - 输入偏移:250µV 电流 - 电源:730µA 电流 - 输出 / 通道:28mA 电压 - 电源，单路/双路(±):2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:管件 |
| LT1722CS5#TRM | 功能描述:IC OPAMP PREC 200MHZ TSOT-23-5 RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:J-FET 电路数:2 输出类型:- 转换速率:13 V/µs 增益带宽积:3MHz -3db带宽:- 电流 - 输入偏压:65pA 电压 - 输入偏移:3000µV 电流 - 电源:1.4mA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作温度:-40°C ~ 85°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-PDIP 包装:管件 |
| LT1722CS5#TRMPBF | 功能描述:IC OPAMP PREC 200MHZ TSOT-23-5 RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 产品培训模块:Differential Circuit Design Techniques for Communication Applications 标准包装:1 系列:- 放大器类型:RF/IF 差分 电路数:1 输出类型:差分 转换速率:9800 V/µs 增益带宽积:- -3db带宽:2.9GHz 电流 - 输入偏压:3µA 电压 - 输入偏移:- 电流 - 电源:40mA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-VQFN 裸露焊盘，CSP 供应商设备封装:16-LFCSP-VQ 包装:剪切带 (CT) 产品目录页面:551 (CN2011-ZH PDF) 其它名称:ADL5561ACPZ-R7CT |
发布紧急采购，3分钟左右您将得到回复。