- 您现在的位置：买卖IC网 > PDF目录13851 > LT1765EFE-2.5#TRPBF (Linear Technology)IC REG BUCK 2.5V 3A 16TSSOP PDF资料下载
参数资料
| 型号： | LT1765EFE-2.5#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 6/20页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK 2.5V 3A 16TSSOP |
| 标准包装： | 2,500 |
| 类型： | 降压（降压） |
| 输出类型： | 固定 |
| 输出数： | 1 |
| 输出电压： | 2.5V |
| 输入电压： | 3 V ~ 25 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 1.25MHz |
| 电流 - 输出： | 3A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm）裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 16-TSSOP-EP |
LT1765/LT1765-1.8/LT1765-2.5/
LT1765-3.3/LT1765-5
PIN FUNCTIONS
FB: The feedback pin is used to set output voltage using
an external voltage divider (adjustable version) that gener-
ates 1.2V at the pin when connected to the desired output
voltage. The ?xed voltage 1.8V, 2.5V, 3.3V and 5V versions
have the divider network included internally and the FB pin
is connected directly to the output. If required, the current
limit can be reduced during start up or short-circuit when
the FB pin is below 0.5V (see the Current Limit Foldback
graph in the Typical Performance Characteristics section).
An impedance of less than 5kΩ on the adjustable version
at the FB pin is needed for this feature to operate.
BOOST: The BOOST pin is used to provide a drive voltage,
higher than the input voltage, to the internal bipolar NPN
power switch.
V IN : This is the collector of the on-chip power NPN switch.
This pin powers the internal circuitry and internal regulator.
At NPN switch on and off, high di/dt edges occur on this
pin. Keep the external bypass capacitor and catch diode
close to this pin. All trace inductance on this path will
create a voltage spike at switch off, adding to the V CE volt-
age across the internal NPN. Both V IN pins of the TSSOP
package must be shorted together on the PC board.
GND: The GND pin acts as the reference for the regulated
output, so load regulation will suffer if the “ground” end of
the load is not at the same voltage as the GND pin of the
IC. This condition will occur when load current or other
currents ?ow through metal paths between the GND pin
V SW : The switch pin is the emitter of the on-chip power
NPN switch. This pin is driven up to the input pin voltage
during switch on time. Inductor current drives the switch
pin negative during switch off time. Negative voltage must
be clamped with an external catch diode with a V BR <0.8V.
Both V SW pins of the TSSOP package must be shorted
together on the PC board.
SYNC: The sync pin is used to synchronize the internal
oscillator to an external signal. It is directly logic compat-
ible and can be driven with any signal between 20% and
80% duty cycle. The synchronizing range is from 1.6MHz
to 2MHz. See Synchronization section in Applications
Information for details. When not in use, this pin should
be grounded.
SHDN : The shutdown pin is used to turn off the regula-
tor and to reduce input drain current to a few microam-
peres. The 1.33V threshold can function as an accurate
undervoltage lockout (UVLO), preventing the regulator
from operating until the input voltage has reached a pre-
determined level. Float or pull high to put the regulator in
the operating mode.
V C : The V C pin is the output of the error ampli?er and the
input of the peak switch current comparator. It is normally
used for frequency compensation, but can do double duty
as a current clamp or control loop override. This pin sits
at about 0.4V for very light loads and 0.9V at maximum
load. It can be driven to ground to shut off the output.
and the load ground point. Keep the ground path short
between the GND pin and the load and use a ground plane
when possible. Keep the path between the input bypass
and the GND pin short. The exposed GND pad and/or GND
pins of the package are directly attached to the internal
tab. These pins/pad should be attached to a large copper
area to reduce thermal resistance.
1765fd
6
相关PDF资料 |
PDF描述 |
|---|---|
| SC54-220 | INDUCTOR SMD 22UH 1.11A 2.52MHZ |
| LT1765EFE-2.5#TR | IC REG BUCK 2.5V 3A 16TSSOP |
| HBM28DRKH | CONN EDGECARD 56POS DIP .156 SLD |
| MAX6715AUTLTD5+T | IC SUPERVISOR MPU SOT23-6 |
| GSM28DRST | CONN EDGECARD 56POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1765EFE-3.3 | 功能描述:IC REG BUCK 3.3V 3A 16TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1765EFE-3.3#PBF | 功能描述:IC REG BUCK 3.3V 3A 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LT1765EFE-3.3#PBF | 制造商:Linear Technology 功能描述:Switching Regulator IC |
| LT1765EFE-3.3#TR | 功能描述:IC REG BUCK 3.3V 3A 16TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1765EFE-3.3#TRPBF | 功能描述:IC REG BUCK 3.3V 3A 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
发布紧急采购，3分钟左右您将得到回复。