- 您现在的位置：买卖IC网 > PDF目录377714 > LT1768IGN (LINEAR TECHNOLOGY CORP) High Power CCFL Controller for Wide Dimming Range and Maximum Lamp Lifetime PDF资料下载
参数资料
| 型号： | LT1768IGN |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | High Power CCFL Controller for Wide Dimming Range and Maximum Lamp Lifetime |
| 中文描述： | 1.5 A FLUORESCENT LIGHT CONTROLLER, 410 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封装： | 0.150 INCH, PLASTIC, SSOP-16 |
| 文件页数： | 10/20页 |
| 文件大小： | 301K |
| 代理商： | LT1768IGN |
LT1768
10
APPLICATIO
S I
N
FOR
ATIO
U
The current mode pulse width modulation produces an
average current in inductor L1 proportional to the VC
voltage. Inductor L1 then acts as a switched mode current
source for a current driven Royer class converter with
efficiencies as high as 90%. T1, C4 and Q1 comprise the
Royer class converter which provides the CCFLs with a
zero DC, 60kHz sinusoidal waveform whose amplitude is
based on the average current in L1. Sinusoidal current
from both CCFLs is then returned to the LT1768 through
the DIO1/2 pins. A fraction of the CCFL current from the
negative half of its sine wave pulls against the internal
current source at the VC pin closing the loop. A single
capacitor on the VC pin provides loop compensation and
CCFL current averaging, which results in constant CCFL
current. Varying the value of the internal current source via
the Multimode Dimming block varies the CCFL current and
resultant CCFL light intensity.
W
U
Multimode Dimming
Previous backlighting solutions have used a traditional
error amplifier in the control loop to regulate lamp current.
The approach converted AC current into a DC voltage for
the input of the error amplifier. This approach used several
time constants in order to provide stable loop compensa-
tion. This compensation scheme meant that the loop had
to be fairly slow and that the output overshoot with start-
up or load conditions had to be carefully evaluated in terms
of transformer stress and breakdown voltage require-
ments. In addition, intensity control schemes were limited
to linear or PWM control. Linear intensity control schemes
provide the highest efficiency backlight circuits but either
limit dimming range, or violate lamp minimum or maxi-
mum CCFL current specifications to achieve wide dim-
ming ratios. PWM control schemes offer wide dimming
range but produce waveforms that may degrade CCFL life,
and waste power at higher CCFL currents. The LT1768’s
Multimode Dimming eliminates the error amplifier con-
cept entirely and combines the best of both control schemes
to extend CCFL life while providing the widest possible
dimming range.
The error amplifier is eliminated by summing the current
out of the Multimode Dimming block with a fraction of
feedback lamp current to form the control loop. This
topology reduces the number of time constants in the
control loop by combining the error signal conversion
scheme and frequency compensation into a single capaci-
tor (VC pin). The control loop thus exhibits the response
of a single pole system, allows for faster loop transient
response and minimizes overshoot under start-up or
overload conditions.
Referring to Figure 2, the source current into the VC pin
from the Multimode Dimming block (and resultant CCFL
current) has five distinct modes of operation. Which mode
is in use is determined by the voltages on the PROG and
PWM pins, and the currents that flow out of the R
MAX
and
R
MIN
pins.
Off Mode (V
PROG
< 0.5V), sets the VC source current to
zero, actively pulls VC to ground, and inhibits the GATE pin
from switching which results in zero lamp current.
Minimum current mode (0.5V < V
PROG
< 1V) sets the VC
source current equal to the current out of the 1.26V
referenced R
MIN
pin. The minimum VC source current
determines the dimming range of the display. Setting
R
RMIN
to produce the manufacturer’s minimum specified
CCFL current guarantees the maximum CCFL lifetime for
all PROG voltages, but limits the dimming range. Setting
R
RMIN
to produce currents less than the manufacturer’s
minimum specified CCFL current increases dimming range,
but places restrictions on the PROG voltage for normal
operation in order to maximize lifetime. To achieve the
maximum dimming ratio possible, I
RMIN
should be set to
zero by connecting the R
MIN
pin to the V
REF
pin.
For example, the circuit in Figure 1 produces a dimming
ratio of 100:1 at 1mA of lamp current, but sets the
minimum CCFL current to zero (R
MIN
is connected to
V
REF
). In this case, the PROG voltage must be kept above
1.12V to limit the CCFL current to 1mA (1mA is only a
typical minimum lamp current used for illustration, con-
sult lamp specifications for actual minimum allowable
value) during normal operation in order to meet CCFL
specifications to maximize lifetime. It should be noted that
taking the PROG voltage in Figure 1 down to 1V (0mA
CCFL current) enables dimming ratios greater than 500:1,
but violates minimum CCFL current specifications in most
lamps and is not recommended. Alternatively, discon-
necting R
MIN
from V
REF
and adding a 10k
resistor from
R
MIN
to AGND in Figure 1 sets the minimum CCFL current
相关PDF资料 |
PDF描述 |
|---|---|
| LT1768 | High Power CCFL Controller with Multimode Dimming(大功率,冷阴极荧光灯(CCFL)控制器(电流型脉宽调制控制器)) |
| LT1769IGN | Constant-Current/ Constant-Voltage 2A Battery Charger with Input Current Limiting |
| LT1769 | Constant-Current/ Constant-Voltage 2A Battery Charger with Input Current Limiting |
| LT1769CGN | Constant-Current/ Constant-Voltage 2A Battery Charger with Input Current Limiting |
| LT1776C | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1768IGN#PBF | 功能描述:IC CTRLR CCFL SGL/MULT HP 16SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 照明，镇流器控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:CCFL 控制器 频率:40 ~ 80 kHz 电流 - 电源:5mA 电流 - 输出:- 电源电压:4.5 V ~ 5.5 V 工作温度:-40°C ~ 85°C 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) 其它名称:90-3991V+V01 |
| LT1768IGN#TR | 功能描述:IC CTRLR CCFL SGL/MULT HP 16SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 照明，镇流器控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:CCFL 控制器 频率:40 ~ 80 kHz 电流 - 电源:5mA 电流 - 输出:- 电源电压:4.5 V ~ 5.5 V 工作温度:-40°C ~ 85°C 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) 其它名称:90-3991V+V01 |
| LT1768IGN#TRPBF | 功能描述:IC CTRLR CCFL SGL/MULT HP 16SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 照明，镇流器控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:CCFL 控制器 频率:40 ~ 80 kHz 电流 - 电源:5mA 电流 - 输出:- 电源电压:4.5 V ~ 5.5 V 工作温度:-40°C ~ 85°C 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) 其它名称:90-3991V+V01 |
| LT1769 | 制造商:LINER 制造商全称:Linear Technology 功能描述:4A, High Efficiency, Standalone Li Battery Charger |
| LT1769CFE | 功能描述:IC BATT CHRGR CNSTNT I/V 20TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。