参数资料
| 型号： | LT1783IS5#TR |
| 厂商： | Linear Technology |
| 文件页数： | 3/16页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP R-R IN/OUT TSOT-23-5 |
| 标准包装： | 2,500 |
| 系列： | Over-The-Top® |
| 放大器类型： | 通用 |
| 电路数： | 1 |
| 输出类型： | 满摆幅 |
| 转换速率： | 0.45 V/µs |
| 增益带宽积： | 1.3MHz |
| 电流 - 输入偏压： | 40nA |
| 电压 - 输入偏移： | 500µV |
| 电流 - 电源： | 230µA |
| 电流 - 输出 / 通道： | 30mA |
| 电压 - 电源，单路/双路(±)： | 2.5 V ~ 18 V，±1.25 V ~ 9 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-5 细型，TSOT-23-5 |
| 供应商设备封装： | TSOT-23-5 |
| 包装： | 带卷 (TR) |
| 其它名称： | LT1783IS5TR |
LT1783
11
1783fd
APPLICATIONS INFORMATION
Supply Voltage
The positive supply pin of the LT1783 should be bypassed
with a small capacitor (typically 0.1μF) within an inch of
the pin. When driving heavy loads, an additional 4.7μF
electrolytic capacitor should be used. When using split
supplies, the same is true for the negative supply pin.
The LT1783 is protected against reverse-battery voltages
up to 18V. In the event a reverse-battery condition occurs,
the supply current is less than 1nA.
Inputs
The LT1783 has two input stages, NPN and PNP (see the
Simplied Schematic), resulting in three distinct operating
regions as shown in the Input Bias Current vs Common
Mode typical performance curve.
For input voltages about 0.8V or more below V+, the PNP
input stage is active and the input bias current is typically
–40nA. When the input common mode voltage is within
0.5V of the positive rail, the NPN stage is operating and
the input bias current is typically 80nA. Increases in tem-
perature will cause the voltage at which operation switches
from the PNP input stage to the NPN input stage to move
towards V+. The input offset voltage of the NPN stage is
untrimmed and is typically 1.8mV.
A Schottky diode in the collector of the input transistors,
along with special geometries for these NPN transistors,
allow the LT1783 to operate with either or both of its inputs
above V+. At about 0.3V above V+, the NPN input transistor
is fully saturated and the input bias current is typically 30μA
at room temperature. The input offset voltage is typically
1.8mV when operating above V+. The LT1783 will operate
with its inputs 18V above V– regardless of V+.
The inputs are protected against excursions as much as
10V below V– by an internal 1k resistor in series with each
input and a diode from the input to the negative supply.
The input stage of the LT1783 incorporates phase reversal
protection to prevent the output from phase reversing for
inputs up to 9V below V–. There are no clamping diodes
between the inputs and the maximum differential input
voltage is 18V.
Output
The output of the LT1783 can swing to within 60mV of the
positive rail with no load and within 3mV of the negative
rail with no load. When monitoring input voltages within
60mV of the positive rail or within 3mV of the negative rail,
gain should be taken to keep the output from clipping. The
LT1783 can sink and source over 30mA at ±5V supplies,
sourcing current is reduced to 10mA at 3V total supplies
as noted in the Electrical Characteristics.
The LT1783 is internally compensated to drive at least
400pF of capacitance under any output loading condi-
tions. A 0.22μF capacitor in series with a 150Ω resistor
between the output and ground will compensate these
ampliers for larger capacitive loads, up to 10,000pF, at
all output currents.
Distortion
There are two main contributors to distortion in op amps:
output crossover distortion as the output transitions from
sourcing to sinking current, and distortion caused by non-
linear common mode rejection. If the op amp is operating
inverting, there is no common mode induced distortion.
If the op amp is operating in the PNP input stage (input is
not within 0.8V of V+), the CMRR is very good, typically
100dB. When the LT1783 switches between input stages,
there is signicant nonlinearity in the CMRR. Lower load
resistance increases the output crossover distortion but
has no effect on the input stage transition distortion. For
lowest distortion, the LT1783 should be operated single
supply, with the output always sourcing current and with
the input voltage swing between ground and (V+ – 0.8V).
See the Typical Performance Characteristics curves,
“Total Harmonic Distortion + Noise vs Output Voltage
Amplitude.”
相关PDF资料 |
PDF描述 |
|---|---|
| LMC7101AIM5 TR | IC OPAMP PRIME 500KHZ SOT23-5 |
| 1SMA15AT3 | TVS 400W 15V UNIDIRECT SMA |
| 1SMA13CAT3 | TVS 400W 13V BIDIRECT SMA |
| 1SMA13AT3 | TVS 400W 13.0V UNIDIRECT SMA |
| 1SMA12AT3 | TVS 400W 5.0V UNIDIRECT SMA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1783IS5-TRMPBF | 制造商:LINEAR_DIMENSIONS 制造商全称:LINEAR_DIMENSIONS 功能描述:1.25MHz, Over-The-Top Micropower, Rail-to-Rail Input and Output Op Amp in SOT-23 |
| LT1783IS6 | 制造商:Linear Technology 功能描述:OP Amp Single GP R-R I/O ±9V/18V 6-Pin TSOT-23 |
| LT1783IS6#PBF | 制造商:Linear Technology 功能描述:SC-Amps/Industrial, Cut Tape SOT-23 uP Op Amp w/ Shutdown |
| LT1783IS6#TR | 功能描述:IC OPAMP R-R IN/OUT SOT23-6 RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:Over-The-Top® 标准包装:1,000 系列:- 放大器类型:电压反馈 电路数:4 输出类型:满摆幅 转换速率:33 V/µs 增益带宽积:20MHz -3db带宽:30MHz 电流 - 输入偏压:2nA 电压 - 输入偏移:3000µV 电流 - 电源:2.5mA 电流 - 输出 / 通道:30mA 电压 - 电源，单路/双路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOIC 包装:带卷 (TR) |
| LT1783IS6#TRM | 功能描述:IC OPAMP R-R IN/OUT SOT23-6 RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:Over-The-Top® 标准包装:1,000 系列:- 放大器类型:电压反馈 电路数:4 输出类型:满摆幅 转换速率:33 V/µs 增益带宽积:20MHz -3db带宽:30MHz 电流 - 输入偏压:2nA 电压 - 输入偏移:3000µV 电流 - 电源:2.5mA 电流 - 输出 / 通道:30mA 电压 - 电源，单路/双路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOIC 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。