参数资料
| 型号： | LT1784IS6#TR |
| 厂商： | Linear Technology |
| 文件页数： | 12/12页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP R-R I/O LOW PWR SOT23-6 |
| 标准包装： | 2,500 |
| 系列： | Over-The-Top® |
| 放大器类型： | 通用 |
| 电路数： | 1 |
| 输出类型： | 满摆幅 |
| 转换速率： | 2.2 V/µs |
| 增益带宽积： | 2.6MHz |
| 电流 - 输入偏压： | 250nA |
| 电压 - 输入偏移： | 1600µV |
| 电流 - 电源： | 750µA |
| 电流 - 输出 / 通道： | 27mA |
| 电压 - 电源，单路/双路(±)： | 2.5 V ~ 18 V，±1.25 V ~ 9 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-6 |
| 供应商设备封装： | TSOT-23-6 |
| 包装： | 带卷 (TR) |
LT1784
9
1784fa
APPLICATIONS INFORMATION
Supply Voltage
The positive supply pin of the LT1784 should be bypassed
with a small capacitor (typically 0.1μF) within an inch of
the pin. When driving heavy loads, and additional 4.7μF
electrolytic capacitor should be used. When using split
supplies the same is true for the negative supply pin.
The LT1784 is protected against reverse battery voltages
up to 18V. In the event a reverse battery condition occurs
the supply current is less than 1nA.
Inputs
The LT1784 has two input stages, NPN and PNP (see the
Simplied Schematic), resulting in three distinct operating
regions as shown in the “Input Bias Current vs Common
Mode” Typical Performance Characteristic curve.
For input voltages about 1V or more below V+, the PNP
input stage is active and the input bias current is typically
–250nA. When the input common mode voltage is within
0.6V of the positive rail, the NPN stage is operating and
the input bias current is typically 500nA. Increases in
temperature will cause the voltage at which operation
switches from the PNP input stage to the NPN input stage
to move towards V+. The input offset voltage of the NPN
stage is untrimmed and is typically 3mV.
A Schottky diode in the collector of the input transistors,
along with special geometries for these NPN transistors,
allow the LT1784 to operate with either or both of its inputs
above V+. At about 0.3V above V+, the NPN input transis-
tors is fully saturated and the input bias current is typically
200μA at room temperature. The input offset voltage is
typically 3mV when operating above V+. The LT1784 will
operate with inputs 18V above V– regardless of V+.
The inputs are protected against excursions as much as
10V below V– by an internal 1k resistor in series with each
input and a diode from the input to the negative supply.
The input stage of the LT1784 incorporates phase reversal
protection to prevent the output from phase reversing for
inputs up to 9V below V–. There are no clamping diodes
between the inputs and the maximum differential input
voltage is 18V.
Output
The output of the LT1784 can swing to within 80mV of the
positive rail and within 4mV of the negative rail with no
load. When monitoring input voltages within 80mV of the
positive rail or within 4mV of the negative rail, gain should
be taken to keep the output from clipping. The LT1784
can typically sink and source over 25mA at ±5V supplies,
sourcing current is reduced to 7.5mA at 3V total supplies
as noted in the Electrical Characteristics section.
The LT1784 is internally compensated to drive at least
400pF of capacitance under any output loading condi-
tions. A 0.22μF capacitor in series with a 150Ω resistor
between the output and ground will compensate these
ampliers for larger capacitive loads, up to 10,000pF at
all output currents.
Distortion
There are two main contributors to distortion in op amps:
output crossover distortion as the output transitions from
sourcing to sinking current, and distortion caused by non-
linear common mode rejection. If the op amp is operating
inverting, there is no common mode induced distortion.
If the op amp is operating in the PNP input stage (input
not within 1V of V+), the CMRR is very good, typically
95dB. When the LT1784 switches between input stages,
there is signicant nonlinearity in the CMRR. Lower load
resistance increases the output crossover distortion but
has no effect on the input stage transition distortion. For
lowest distortion, the LT1784 should be operated single
supply, with the output always sourcing current and with
the input voltage swing between ground and (V+ – 1V). See
Typical Performance Characteristics curve, “Total Harmonic
Distortion + Noise vs Output Voltage Amplitude.”
Gain
The open-loop gain is almost independent of load when
the output is sourcing current. This optimizes performance
in single supply applications where the load is returned
to ground. The Typical Performance Characteric curve
“Open-Loop Gain” for various loads shows the details.
相关PDF资料 |
PDF描述 |
|---|---|
| TSW-105-26-S-S | CONN HEADER 5POS .100" SGL GOLD |
| LT1784IS6#TRM | IC OPAMP R-R IN/OUT SOT23-6 |
| MMD25-0051G1 | CONN RACK/PANEL 5POS 5A |
| TSW-147-26-T-D | CONN HEADER 94POS .100" DUAL TIN |
| LT6230CS6#TRPBF | IC OP AMP 3.4MA 215MHZ SOT23-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1785 | 制造商:LINER 制造商全称:Linear Technology 功能描述:20Mbps RS485 Transceivers |
| LT1785_1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:60V Fault Protected RS485/RS422 Transceivers |
| LT1785A | 制造商:LINER 制造商全称:Linear Technology 功能描述:60V Fault Protected RS485/RS422 Transceivers |
| LT1785AC | 制造商:LINER 制造商全称:Linear Technology 功能描述:60V Fault Protected RS485/RS422 Transceivers |
| LT1785ACN8 | 功能描述:IC TXRX 60V RS485/RS422 8DIP RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:27 系列:- 类型:收发器 驱动器/接收器数:3/3 规程:RS232，RS485 电源电压:4.75 V ~ 5.25 V 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。