- 您现在的位置：买卖IC网 > PDF目录377716 > LT1800IS8 (LINEAR TECHNOLOGY CORP) 80MHz, 25V/ms Low Power Rail-to-Rail Input and Output Precision Op Amp PDF资料下载
参数资料
| 型号： | LT1800IS8 |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 运动控制电子 |
| 英文描述： | 80MHz, 25V/ms Low Power Rail-to-Rail Input and Output Precision Op Amp |
| 中文描述： | OP-AMP, 4500 uV OFFSET-MAX, 65 MHz BAND WIDTH, PDSO8 |
| 封装： | 0.150 INCH, PLASTIC, SO-8 |
| 文件页数： | 13/16页 |
| 文件大小： | 266K |
| 代理商： | LT1800IS8 |
13
LT1800
1800f
APPLICATIOU
diodes should be limited to less than 10mA when they are
active. The worst-case differential input voltage usually
occurs when the input is driven while the output is shorted
to ground in a unity gain configuration. In addition, the
amplifier is protected against ESD strikes up to 3kV on all
pins by a pair of protection diodes on each pin that are
connected to the power supplies as shown in Figure1.
W
U
U
Capacitive Load
The LT1800 is optimized for high bandwidth, low power
and precision applications. It can drive a capacitive load of
about 75pF in a unity gain configuration, and more for
higher gain. When driving a larger capacitive load, a
resistor of 10
to 50
should be connected between the
output and the capacitive load to avoid ringing or oscilla-
tion. The feedback should still be taken from the output so
that the resistor will isolate the capacitive load to ensure
stability. Graphs on capacitive loads indicate the transient
response of the amplifier when driving capacitive load with
a specified series resistor.
Feedback Components
When feedback resistors are used to set up gain, care must
be taken to ensure that the pole formed by the feedback
resistors and the total capacitance at the inverting input
does not degrade stability. For instance, the LT1800 in a
noninverting gain of 2, set up with two 5k resistors and a
capacitance of 5pF (part plus PC board) will probably ring
in transient response. The pole is formed at 12.7MHz that
will reduce phase margin by 32 degrees when the cross-
over frequency of the amplifier is around 20MHz. A capaci-
tor of 5pF or higher connected across the feedback resis-
tor will eliminate any ringing or oscillation.
APPLICATIU
Single Supply 1A Laser Driver Amplifier
The circuit in the front page of this data sheet shows the
LT1800 used in a 1A laser driver application. One of the
reasons the LT1800 is well suited to this control task is that
its 2.3V operation ensures that it will be awake during
power-up and operated before the circuit can otherwise
cause significant current to flow in the 2.1V threshold laser
diode. Driving the noninverting input of the LT1800 to a
voltage V
IN
will control the turning on of the high current
NPN transistor, FMMT619 and the laser diode. A current
equal to V
IN
/R1 flows through the laser diode. The LT1800
low offset voltage and low input bias current allows it to
control the current that flows through the laser diode
precisely. The overall circuit is a 1A per Volt V-to-I con-
verter. Frequency compensation components R2 and C1
are selected for fast but zero-overshoot time domain
response to avoid overcurrent conditions in the laser. The
time domain response of this circuit, measured at R1 and
given a 500mV 230ns input pulse, is also shown in the
graphic on the front page. While the circuit is capable of 1A
operation, the laser diode and the transistor are thermally
limited due to power dissipation, so they must be operated
at low duty cycles.
W
U
U
Fast 1A Current Sense Amplifier
A simple, fast current sense amplifier in Figure 2 is suitable
for quickly responding to out-of-range currents. The cir-
cuit amplifies the voltage across the 0.1
sense resistor
by a gain of 20, resulting in a conversion gain of 2V/A. The
–3dB bandwidth of the circuit is 4MHz, and the uncertainty
due to V
OS
and I
B
is less than 4mA. The minimum output
voltage is 60mV, corresponding to 30mA. The large-signal
response of the circuit is shown in Figure 3.
+
–
LT1800
0.1
I
L
0A TO 1A
V
OUT
0V TO 2V
V
OUT
= 2 I
L
f
–3dB
= 4MHz
UNCERTAINTY DUE TO V
OS,
I
B
< 4mA
3V
1k
1800 F02
52.3
52.3
Figure 2. Fast 1A Current Sense
相关PDF资料 |
PDF描述 |
|---|---|
| LT1800CS5 | 80MHz, 25V/ms Low Power Rail-to-Rail Input and Output Precision Op Amp |
| LT1809CS8 | 180MHz, 350V/ms Rail-to-Rail Input and Output Low Distortion Op Amp |
| LT1809IS8 | 180MHz, 350V/ms Rail-to-Rail Input and Output Low Distortion Op Amp |
| LT1809 | 180MHz, 350V/ms Rail-to-Rail Input and Output Low Distortion Op Amp |
| LT1815CS6 | Single/Dual/Quad 220MHz, 1500V/us Operational Amplifiers with Programmable Supply Current |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1800IS8#PBF | 功能描述:IC OP-AMP R-R IN/OUT LOPWR 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 产品培训模块:Differential Circuit Design Techniques for Communication Applications 标准包装:1 系列:- 放大器类型:RF/IF 差分 电路数:1 输出类型:差分 转换速率:9800 V/µs 增益带宽积:- -3db带宽:2.9GHz 电流 - 输入偏压:3µA 电压 - 输入偏移:- 电流 - 电源:40mA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-VQFN 裸露焊盘，CSP 供应商设备封装:16-LFCSP-VQ 包装:剪切带 (CT) 产品目录页面:551 (CN2011-ZH PDF) 其它名称:ADL5561ACPZ-R7CT |
| LT1800IS8#TR | 功能描述:IC OP-AMP R-R IN/OUT LOPWR 8SOIC RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1,000 系列:- 放大器类型:电压反馈 电路数:4 输出类型:满摆幅 转换速率:33 V/µs 增益带宽积:20MHz -3db带宽:30MHz 电流 - 输入偏压:2nA 电压 - 输入偏移:3000µV 电流 - 电源:2.5mA 电流 - 输出 / 通道:30mA 电压 - 电源，单路/双路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOIC 包装:带卷 (TR) |
| LT1800IS8#TRPBF | 功能描述:IC OP-AMP R-R IN/OUT LOPWR 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1,000 系列:- 放大器类型:电压反馈 电路数:4 输出类型:满摆幅 转换速率:33 V/µs 增益带宽积:20MHz -3db带宽:30MHz 电流 - 输入偏压:2nA 电压 - 输入偏移:3000µV 电流 - 电源:2.5mA 电流 - 输出 / 通道:30mA 电压 - 电源，单路/双路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOIC 包装:带卷 (TR) |
| LT1801 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Single/Dual/Quad 60MHz, 20V/us, Low Power, Rail-to-Rail Input and Output Precision Op Amps |
| LT1801CDD | 功能描述:IC PREC OPAMP R-R DUAL LP 8DFN RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:LinCMOS™ 放大器类型:通用 电路数:4 输出类型:- 转换速率:0.05 V/µs 增益带宽积:110kHz -3db带宽:- 电流 - 输入偏压:0.7pA 电压 - 输入偏移:210µV 电流 - 电源:57µA 电流 - 输出 / 通道:30mA 电压 - 电源，单路/双路(±):3 V ~ 16 V，±1.5 V ~ 8 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOIC 包装:管件 产品目录页面:865 (CN2011-ZH PDF) 其它名称:296-1834296-1834-5 |
发布紧急采购，3分钟左右您将得到回复。