- 您现在的位置：买卖IC网 > PDF目录377716 > LT1816AIMS (LINEAR TECHNOLOGY CORP) Single/Dual/Quad 220MHz, 1500V/us Operational Amplifiers with Programmable Supply Current PDF资料下载
参数资料
| 型号： | LT1816AIMS |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 运动控制电子 |
| 英文描述： | Single/Dual/Quad 220MHz, 1500V/us Operational Amplifiers with Programmable Supply Current |
| 中文描述： | DUAL OP-AMP, 3000 uV OFFSET-MAX, 220 MHz BAND WIDTH, PDSO10 |
| 封装： | PLASTIC, MSOP-10 |
| 文件页数： | 12/20页 |
| 文件大小： | 366K |
| 代理商： | LT1816AIMS |
12
LT1815
LT1816/LT1817
181567fa
APPLICATIOU
W
U
U
Layout and Passive Components
As with all high speed amplifiers, the LT1815/LT1816/
LT1817 require some attention to board layout. A ground
plane is recommended and trace lengths should be mini-
mized, especially on the negative input lead.
Low ESL/ESR bypass capacitors should be placed directly
at the positive and negative supply (0.01
μ
F ceramics are
recommended). For high drive current applications, addi-
tional 1
μ
F to 10
μ
F tantalums should be added.
The parallel combination of the feedback resistor and gain
setting resistor on the inverting input combine with the
input capacitance to form a pole that can cause peaking or
even oscillations. If feedback resistors greater than 1k are
used, a parallel capacitor of value:
C
F
> R
G
C
IN
/R
F
should be used to cancel the input pole and optimize
dynamic performance. For applications where the DC
noise gain is 1 and a large feedback resistor is used, C
F
should be greater than or equal to C
IN
. An example would
be an I-to-V converter.
Input Considerations
The inputs of the LT1815/LT1816/LT1817 amplifiers are
connected to the base of an NPN and PNP bipolar transis-
tor in parallel. The base currents are of opposite polarity
and provide first-order bias current cancellation. Due to
variation in the matching of NPN and PNP beta, the
polarity of the input bias current can be positive or
negative. The offset current, however, does not depend
on beta matching and is tightly controlled. Therefore, the
use of balanced source resistance at each input is recom-
mended for applications where DC accuracy must be
maximized. For example, with a 100
source resistance
at each input, the 800nA maximum offset current results
in only 80
μ
V of extra offset, while without balance the 8
μ
A
maximum input bias current could result in a 0.8mV offset
contribution.
The inputs can withstand differential input voltages of up
to 6V without damage and without needing clamping or
series resistance for protection. This differential input
voltage generates a large internal current (up to 80mA),
which results in the high slew rate. In normal transient
closed-loop operation, this does not increase power
dissipation significantly because of the low duty cycle of
the transient inputs. Sustained differential inputs, how-
ever, will result in excessive power dissipation and there-
fore
this device should not be used as a comparator
.
Capacitive Loading
The LT1815/LT1816/LT1817 are optimized for high band-
width and low distortion applications. They can drive a
capacitive load of 10pF in a unity-gain configuration and
more with higher gain. When driving a larger capacitive
load, a resistor of 10
to 50
should be connected
between the output and the capacitive load to avoid ringing
or oscillation. The feedback should still be taken from the
output so that the resistor will isolate the capacitive load
to ensure stability.
Slew Rate
The slew rate of the LT1815/LT1816/LT1817 is proportional
to the differential input voltage. Therefore, highest slew rates
are seen in the lowest gain configurations. For example, a
5V output step in a gain of 10 has a 0.5V input step, whereas
in unity gain there is a 5V input step. The LT1815/LT1816/
LT1817 are tested for a slew rate in a gain of –1. Lower
slew rates occur in higher gain configurations.
Programmable Supply Current
(LT1815/LT1816A)
In order to operate the LT1815S6 or LT1816A at full speed
(and full supply current), connect the I
SET
pin to the
negative supply through a resistance of 75
or less.
To adjust or program the supply current and speed of the
LT1815S6 or LT1816A, connect an external resistor (R
SET
)
between the I
SET
pin and the negative supply as shown in
Figure 1. The amplifiers are fully functional with 0
≤
R
SET
≤
40k. Figures 2 and 3 show how the gain bandwidth and
supply current vary with the value of the programming
resistor R
SET
. In addition, the Electrical Characteristics
section of the data sheet specifies maximum supply
current and offset voltage, as well as minimum gain
bandwidth and output current at the maximum R
SET
value
of 40k.
相关PDF资料 |
PDF描述 |
|---|---|
| LT1816IMS8 | Single/Dual/Quad 220MHz, 1500V/us Operational Amplifiers with Programmable Supply Current |
| LT1816IS8 | Single/Dual/Quad 220MHz, 1500V/us Operational Amplifiers with Programmable Supply Current |
| LT1817 | Single/Dual/Quad 220MHz, 1500V/us Operational Amplifiers with Programmable Supply Current |
| LT1817CS | Single/Dual/Quad 220MHz, 1500V/us Operational Amplifiers with Programmable Supply Current |
| LT1817IS | Single/Dual/Quad 220MHz, 1500V/us Operational Amplifiers with Programmable Supply Current |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1816AIMS#PBF | 功能描述:IC OP-AMP 220MHZ DUAL 10-MSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:- 放大器类型:通用 电路数:1 输出类型:满摆幅 转换速率:0.11 V/µs 增益带宽积:350kHz -3db带宽:- 电流 - 输入偏压:4nA 电压 - 输入偏移:20µV 电流 - 电源:260µA 电流 - 输出 / 通道:20mA 电压 - 电源，单路/双路(±):2.7 V ~ 36 V，±1.35 V ~ 18 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SO 包装:带卷 (TR) |
| LT1816AIMS#TR | 功能描述:IC OP-AMP 220MHZ DUAL 10-MSOP RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:LinCMOS™ 放大器类型:通用 电路数:4 输出类型:- 转换速率:0.05 V/µs 增益带宽积:110kHz -3db带宽:- 电流 - 输入偏压:0.7pA 电压 - 输入偏移:210µV 电流 - 电源:57µA 电流 - 输出 / 通道:30mA 电压 - 电源，单路/双路(±):3 V ~ 16 V，±1.5 V ~ 8 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOIC 包装:管件 产品目录页面:865 (CN2011-ZH PDF) 其它名称:296-1834296-1834-5 |
| LT1816AIMS#TRPBF | 功能描述:IC OP-AMP 220MHZ DUAL 10-MSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:- 放大器类型:通用 电路数:1 输出类型:满摆幅 转换速率:0.11 V/µs 增益带宽积:350kHz -3db带宽:- 电流 - 输入偏压:4nA 电压 - 输入偏移:20µV 电流 - 电源:260µA 电流 - 输出 / 通道:20mA 电压 - 电源，单路/双路(±):2.7 V ~ 36 V，±1.35 V ~ 18 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SO 包装:带卷 (TR) |
| LT1816CDD | 功能描述:IC OPAMP 220MHZ DUAL LP HS 8DFN RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1,000 系列:- 放大器类型:电压反馈 电路数:4 输出类型:满摆幅 转换速率:33 V/µs 增益带宽积:20MHz -3db带宽:30MHz 电流 - 输入偏压:2nA 电压 - 输入偏移:3000µV 电流 - 电源:2.5mA 电流 - 输出 / 通道:30mA 电压 - 电源，单路/双路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOIC 包装:带卷 (TR) |
| LT1816CDD#PBF | 功能描述:IC OPAMP 220MHZ DUAL LP HS 8DFN RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1,000 系列:- 放大器类型:电压反馈 电路数:4 输出类型:满摆幅 转换速率:33 V/µs 增益带宽积:20MHz -3db带宽:30MHz 电流 - 输入偏压:2nA 电压 - 输入偏移:3000µV 电流 - 电源:2.5mA 电流 - 输出 / 通道:30mA 电压 - 电源，单路/双路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOIC 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。