- 您现在的位置：买卖IC网 > PDF目录14099 > LT1931IS5#TRPBF (Linear Technology)IC REG INV 1A TSOT23-5 PDF资料下载
参数资料
| 型号： | LT1931IS5#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 6/12页 |
| 文件大小： | 0K |
| 描述： | IC REG INV 1A TSOT23-5 |
| 标准包装： | 2,500 |
| 类型： | 反相 |
| 输出数： | 1 |
| 输入电压： | 2.45 V ~ 16 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 1.2MHz |
| 电流 - 输出： | 1A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-5 细型，TSOT-23-5 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | TSOT-23-5 |
LT1931/LT1931A
APPLICATIO S I FOR ATIO
The inductors shown in Table 2 for use with the LT1931A
were chosen for their small size. For better efficiency, use
similar valued inductors with a larger volume. For in-
stance, the Sumida CR43 series, in values ranging from
3.3 μ H to 10 μ H, will give a LT1931A application a few
percentage points increase in efficiency.
CAPACITOR SELECTION
Low ESR (equivalent series resistance) capacitors should
be used at the output to minimize the output ripple voltage.
zero to the system. For the tantalum and OS-CON capaci-
tors, this zero is located at a lower frequency due to the
higher value of the ESR, while the zero of a ceramic
capacitor is at a much higher frequency and can generally
be ignored.
A phase lead zero can be intentionally introduced by
placing a capacitor (C4) in parallel with the resistor (R1)
between V OUT and V NFB as shown in Figure 1. The
frequency of the zero is determined by the following
equation.
Multilayer ceramic capacitors are an excellent choice, as
they have an extremely low ESR and are available in very
small packages. X5R dielectrics are preferred, followed by
? Z =
1
2 π ? R 1 ? C 4
X7R, as these materials retain their capacitance over wide
voltage and temperature ranges. A 10 μ F to 22 μ F output
capacitor is sufficient for most LT1931 applications while
a 4.7 μ F to 10 μ F capacitor will suffice for the LT1931A.
Solid tantalum or OS-CON capacitors can be used, but
they will occupy more board area than a ceramic and will
have a higher ESR. Always use a capacitor with a sufficient
voltage rating.
Ceramic capacitors also make a good choice for the input
decoupling capacitor, which should be placed as close as
possible to the LT1931/LT1931A. A 1 μ F to 4.7 μ F input
capacitor is sufficient for most applications. Table 3 shows
a list of several ceramic capacitor manufacturers. Consult
the manufacturers for detailed information on their entire
selection of ceramic parts.
Table 3. Ceramic Capacitor Manufacturers
By choosing the appropriate values for the resistor and
capacitor, the zero frequency can be designed to improve
the phase margin of the overall converter. The typical
target value for the zero frequency is between 20kHz to
60kHz. Figure 3 shows the transient response of the
inverting converter from Figure 1 without the phase lead
capacitor C4. The phase margin is reduced as evidenced
by more ringing in both the output voltage and inductor
current. A 220pF capacitor for C4 results in better phase
margin, which is revealed in Figure 4 as a more damped
response and less overshoot. Figure 5 shows the transient
response when a 22 μ F tantalum capacitor with no phase
lead capacitor is used on the output. The higher output
voltage ripple is revealed in the upper waveform as a
thicker line. The transient response is adequate which
implies that the ESR zero is improving the phase margin.
Taiyo Yuden
(408) 573-4150
www.t-yuden.com
AVX
Murata
(803) 448-9411
www.avxcorp.com
(714) 852-2001
www.murata.com
V OUT
20mV/DIV
AC COUPLED
I L1A + I L1B
0.5A/DIV
AC COUPLED
The decision to use either low ESR (ceramic) capacitors or
LOAD 200mA
CURRENT 100mA
the higher ESR (tantalum or OS-CON) capacitors can
100 μ s/DIV
1931 F03
effect the stability of the overall system. The ESR of any
capacitor, along with the capacitance itself, contributes a
Figure 3. Transient Response of Inverting Converter
Without Phase Lead Capacitor
1931fa
6
相关PDF资料 |
PDF描述 |
|---|---|
| LT1931AIS5#TRMPBF | IC REG INV 1A TSOT23-5 |
| V375C8C100BL | CONVERTER MOD DC/DC 8V 100W |
| LT1931IS5#TRMPBF | IC REG INV 1A TSOT23-5 |
| V300C8C100BL | CONVERTER MOD DC/DC 8V 100W |
| LTC3403EDD#TR | IC REG BUCK SYNC ADJ 0.6A 8DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1932 | 制造商:LINER 制造商全称:Linear Technology 功能描述:20mA LED Driver and OLED Driver with Integrated Schottky in 3mm x 2mm DFN |
| LT1932ES6 | 制造商:Linear Technology 功能描述:LED DRVR 8Segment 1.8V/2.5V/3.3V/5V/9V 6-Pin TSOT-23 |
| LT1932ES6#PBF | 制造商:Linear Technology 功能描述:LED DRVR 8Segment 1.8V/2.5V/3.3V/5V/9V 6-Pin TSOT-23 制造商:Linear Technology 功能描述:LED DRVR 8Segment 1.8V/2.5V/3.3V/5V/9V 6-Pin TSOT-23 Bulk 制造商:Linear Technology 功能描述:IC DC/DC CONVERT/LED DR 6SOT2 制造商:Linear Technology 功能描述:IC, DC/DC CONVERT/LED DR, 6SOT2 制造商:Linear Technology 功能描述:IC LED DRIVER CONST CURRENT/BOOST SOT236; Topology:Boost, Constant Current; No. of Outputs:1; Output Current:550mA; Output Voltage:36V; Driver Case Style:SOT-23; Input Voltage Min:1V; Input Voltage Max:10V; Dimming Control Type:PWM ;RoHS Compliant: Yes |
| LT1932ES6#PBF | 制造商:Linear Technology 功能描述:DC/DC Converter IC |
| LT1932ES6#TR | 功能描述:IC LED DRIVR WHITE BCKLGT TSOT-6 RoHS:否 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
发布紧急采购，3分钟左右您将得到回复。