- 您现在的位置：买卖IC网 > PDF目录79923 > LT1934IDCB-1#PBF (LINEAR TECHNOLOGY CORP) 0.49 A SWITCHING REGULATOR, PDSO6 PDF资料下载
参数资料
| 型号： | LT1934IDCB-1#PBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | 0.49 A SWITCHING REGULATOR, PDSO6 |
| 封装： | 2 X 3 MM, 0.80 MM HEIGHT, LEAD FREE, PLASTIC, MO-229, DFN-6 |
| 文件页数： | 4/20页 |
| 文件大小： | 234K |
| 代理商： | LT1934IDCB-1#PBF |
LT1934/LT1934-1
12
1934fe
APPLICATIONS INFORMATION
maximum duty cycle of the LT1934, requiring a higher
input voltage to maintain regulation.
Shorted Input Protection
If the inductor is chosen so that it won’t saturate exces-
sively, an LT1934 buck regulator will tolerate a shorted
output. There is another situation to consider in systems
where the output will be held high when the input to the
LT1934 is absent. This may occur in battery charging ap-
plications or in battery backup systems where a battery
or some other supply is diode OR-ed with the LT1934’s
output. If the VIN pin is allowed to oat and the SHDN pin
is held high (either by a logic signal or because it is tied
Figure 3. The Minimum Input Voltage Depends
on Output Voltage, Load Current and Boost Circuit
Minimum Input Voltage VOUT = 3.3V
Minimum Input Voltage VOUT = 5V
LOAD CURRENT (mA)
3.5
INPUT
VOLTAGE
(V)
4.0
4.5
5.0
5.5
6.0
0.1
10
100
1934 G12
3.0
1
LT1934
VOUT = 3.3V
TA = 25°C
BOOST DIODE TIED TO OUTPUT
VIN TO START
VIN TO RUN
LOAD CURRENT (mA)
5
INPUT
VOLTAGE
(V)
6
7
8
0.1
10
100
1934 G13
4
1
LT1934
VOUT = 5V
TA = 25°C
BOOST DIODE TIED TO OUTPUT
VIN TO START
VIN TO RUN
to VIN), then the LT1934’s internal circuitry will pull its
quiescent current through its SW pin. This is ne if your
system can tolerate a few mA in this state. If you ground
the SHDN pin, the SW pin current will drop to essentially
zero. However, if the VIN pin is grounded while the output
is held high, then parasitic diodes inside the LT1934 can
pull large currents from the output through the SW pin
and the VIN pin. Figure 4 shows a circuit that will run only
when the input voltage is present and that protects against
a shorted or reversed input.
Figure 4. Diode D4 Prevents a Shorted Input from Discharging
a Backup Battery Tied to the Output; It Also Protects the Circuit
from a Reversed Input. The LT1934 Runs Only When the Input
is Present
VIN
BOOST
GND
FB
SHDN
SW
5
D4
VIN
4
1
6
23
1M
100k
LT1934
1934 F07
VOUT
BACKUP
D4: MBR0530
PCB Layout
For proper operation and minimum EMI, care must be
taken during printed circuit board layout. Figure 5 shows
the high current paths in the buck regulator circuit. Note
that large, switched currents ow in the power switch,
the catch diode (D1) and the input capacitor (C2). The
loop formed by these components should be as small as
possible. Furthermore, the system ground should be tied
to the regulator ground in only one place; this prevents
the switched current from injecting noise into the system
ground. These components, along with the inductor and
output capacitor, should be placed on the same side of
the circuit board, and their connections should be made
on that layer. Place a local, unbroken ground plane below
these components, and tie this ground plane to system
ground at one location, ideally at the ground terminal of
the output capacitor C1. Additionally, the SW and BOOST
nodes should be kept as small as possible. Finally, keep
the FB node as small as possible so that the ground pin
相关PDF资料 |
PDF描述 |
|---|---|
| LSM-0.8/10-D3 | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| LSN-1/10-D3H-C | 1-OUTPUT 10 W DC-DC REG PWR SUPPLY MODULE |
| LK4003-9RD6TB1 | 1-OUTPUT AC-DC PWR FACTOR CORR MODULE |
| LT4180EGN#PBF | POWER SUPPLY SUPPORT CKT, PDSO24 |
| LM3622MX-4.2/NOPB | BATTERY CHARGE CONTROLLER, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1934IS6 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Micropower Step-Down Switching Regulators in ThinSOT |
| LT1934IS6#PBF | 制造商:Linear Technology 功能描述:Conv DC-DC Single Step Down 3.2V to 34V 6-Pin TSOT-23 制造商:Linear Technology 功能描述:SP-SWREG/Monolithic, Cut Tape 300mA (Iout), Micropower Step-Down |
| LT1934IS6#TR | 功能描述:IC REG BUCK ADJ 0.3A SOT23-6 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LT1934IS6#TRM | 功能描述:IC REG BUCK ADJ 0.3A SOT23-6 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT1934IS6#TRMPBF | 功能描述:IC REG BUCK ADJ 0.3A SOT23-6 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
发布紧急采购，3分钟左右您将得到回复。