- 您现在的位置：买卖IC网 > PDF目录14042 > LT1940LEFE#TR (Linear Technology)IC REG BUCK ADJ 1.4A DL 16TSSOP PDF资料下载
参数资料
| 型号： | LT1940LEFE#TR |
| 厂商： | Linear Technology |
| 文件页数： | 12/20页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 1.4A DL 16TSSOP |
| 标准包装： | 2,500 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 2 |
| 输出电压： | 1.25 V ~ 6.16 V |
| 输入电压： | 3.6 V ~ 7 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 1.1MHz |
| 电流 - 输出： | 1.4A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm）裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 16-TSSOP-EP |
LT1940/LT1940L
APPLICATIO S I FOR ATIO
The boost circuit can also run directly from a DC voltage
that is higher than the input voltage by more than 3V, as in
Figure 3d. The diode is used to prevent damage to the
LT1940 in case V IN2 is held low while V IN is present. The
circuit saves several components (both BOOST pins can
be tied to D2). However, efficiency may be lower and
dissipation in the LT1940 may be higher. Also, if V IN2 is
absent, the LT1940 will still attempt to regulate the output,
but will do so with very low efficiency and high dissipation
because the switch will not be able to saturate, dropping
1.5V to 2V in conduction.
The minimum input voltage of an LT1940 application is
limited by the minimum operating voltage (< 3.6V) and by
the maximum duty cycle as outlined above. For proper
start-up, the minimum input voltage is also limited by the
boost circuit. If the input voltage is ramped slowly, or the
LT1940 is turned on with its RUN/SS pin when the output
is already in regulation, then the boost capacitor may not
be fully charged. Because the boost capacitor is charged
with the energy stored in the inductor, the circuit will rely
on some minimum load current to get the boost circuit
running properly. This minimum load will depend on input
and output voltages, and on the arrangement of the boost
circuit. The minimum load generally goes to zero once the
circuit has started. The Typical Performance Characteris-
tics section shows plots of the minimum load current to
start and to run as a function of input voltage for 3.3V and
5V outputs. In many cases the discharged output capaci-
tor will present a load to the switcher which will allow it to
start. The plots show the worst-case situation where V IN
is ramping very slowly. Use a Schottky diode (such as the
BAT-54) for the lowest start-up voltage.
of the loop compensation but is used to filter noise at the
switching frequency.
Loop compensation determines the stability and transient
performance. Designing the compensation network is a
bit complicated and the best values depend on the appli-
cation and in particular the type of output capacitor. A
practical approach is to start with one of the circuits in this
data sheet that is similar to your application and tune the
compensation network to optimize the performance. Sta-
bility should then be checked across all operating condi-
tions, including load current, input voltage and tempera-
ture. The LT1375 data sheet contains a more thorough
discussion of loop compensation and describes how to
test the stability using a transient load.
Figure 4 shows an equivalent circuit for the LT1940
control loop. The error amp is a transconductance ampli-
fier with finite output impedance. The power section,
consisting of the modulator, power switch and inductor, is
modeled as a transconductance amplifier generating an
output current proportional to the voltage at the V C pin.
Note that the output capacitor integrates this current, and
that the capacitor on the V C pin (C C ) integrates the error
amplifier output current, resulting in two poles in the loop.
In most cases a zero is required and comes from either the
output capacitor ESR or from a resistor in series with C C .
This simple model works well as long as the value of the
inductor is not too high and the loop crossover frequency
is much lower than the switching frequency. A phase lead
capacitor (C PL ) across the feedback divider may improve
the transient response.
LT1940
Frequency Compensation
CURRENT MODE
POWER STAGE
V SW
OUTPUT
The LT1940 uses current mode control to regulate the
g m = 2.5mho
ERROR
AMPLIFIER
R1
C PL
output. This simplifies loop compensation. In particular,
the LT1940 does not require the ESR of the output
capacitor for stability so you are free to use ceramic
capacitors to achieve low output ripple and small circuit
size.
Frequency compensation is provided by the components
GND
V C
R C
500k
g m =
340 μ mho
C F
FB
1.25V
R2
ESR
+
C1
POLYMER
OR
TANTALUM
C1
CERAMIC
tied to the V C pin. Generally a capacitor and a resistor in
series to ground determine loop gain. In addition, there is
a lower value capacitor in parallel. This capacitor is not part
C C
1940 F05
Figure 4. Model for Loop Response
1940fa
12
相关PDF资料 |
PDF描述 |
|---|---|
| V24B24E200BL3 | CONVERTER MOD DC/DC 24V 200W |
| V24B24E200BL2 | CONVERTER MOD DC/DC 24V 200W |
| V24B24E200BL | CONVERTER MOD DC/DC 24V 200W |
| LTC3619BIMSE#PBF | IC REG BUCK SYNC ADJ DL 10MSOP |
| V24B24E200B2 | CONVERTER MOD DC/DC 24V 200W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1941 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Triple Monolithic Switching Regulator |
| LT1941EFE | 功能描述:IC REG MULTI CONFIG TRPL 28TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1941EFE#PBF | 功能描述:IC REG MULTI CONFIG TRPL 28TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:MIC23xxx HyperLight Load™ Regulators 标准包装:5,000 系列:HyperLight Load® 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.8V 输入电压:2.7 V ~ 5.5 V PWM 型:混合物 频率 - 开关:4MHz 电流 - 输出:2A 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘，8-MLF? 包装:带卷 (TR) 供应商设备封装:8-MLF?（2x2） 产品目录页面:1094 (CN2011-ZH PDF) 其它名称:576-3303-2 |
| LT1941EFE#TR | 功能描述:IC REG MULTI CONFIG TRPL 28TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1941EFE#TRPBF | 功能描述:IC REG MULTI CONFIG TRPL 28TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
发布紧急采购，3分钟左右您将得到回复。