- 您现在的位置：买卖IC网 > PDF目录14798 > LT1956IGN#PBF (Linear Technology)IC REG BUCK ADJ 1.5A 16SSOP PDF资料下载
参数资料
| 型号： | LT1956IGN#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 12/28页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 1.5A 16SSOP |
| 标准包装： | 100 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.2 V ~ 45 V |
| 输入电压： | 5.5 V ~ 60 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 500kHz |
| 电流 - 输出： | 1.5A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 包装： | 管件 |
| 供应商设备封装： | 16-SSOP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页当前第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LT1956/LT1956-5
APPLICATIO S I FOR ATIO
<
I P 2 I P 2 ( f )( L )( V IN )
2 ( V OUT + V F )( V IN – V OUT ? V F )
1 . 5 2 ( 500 ? 10 3 )( 4 ? 10 ? 6 )( 15 )
2 ( 5 + 0 . 63 )( 15 – 5 – 0 . 63 )
solution.Themaximumoutputloadcurrentindiscontinu-
ous mode, however, must be calculated and is defined
later in this section.
Discontinuous mode is entered when the output load
current is less than one-half of the inductor ripple current
(I LP-P ). In this mode, inductor current falls to zero before
the next switch turn-on (see Figure 8). Buck converters
will be in discontinuous mode for output load current
given by:
I OUT Discontinous Mode
( V OUT + V F )( V IN – V OUT – V F )
( 2 )( V IN )( f )( L )
The inductor value in a buck converter is usually chosen
large enough to keep inductor ripple current (I LP-P ) low;
this is done to minimize output ripple voltage and maxi-
mize output load current. In the case of large inductor
values, as seen in the equation above, discontinuous
mode will be associated with “light loads.”
When choosing small inductor values, however, discon-
tinuous mode will occur at much higher output load
currents. The limit to the smallest inductor value that can
be chosen is set by the LT1956 peak switch current (I P )
and the maximum output load current required given by:
I OUT(MAX) Discontinuous Mode
= =
2 ( I LP-P )
Example: For V IN = 15V, V OUT = 5V, V F = 0.63V, f = 500kHz
and L = 4 μ H
I OUT ( MAX ) Discontinuous Mode
=
I OUT(MAX) Discontinuous Mode = 0.639A
load current is required, the inductor value must be
increased. If I OUT(MAX) no longer meets the discontinuous
mode criteria, use the I OUT(MAX) equation for continuous
mode; the LT1956 is designed to operate well in both
modes of operation, allowing a large range of inductor
values to be used.
SHORT-CIRCUIT CONSIDERATIONS
For a ground short-circuit fault on the regulated output,
the maximum input voltage for the LT1956 is typically
limited to 25V. If a greater input voltage is required,
increasing the resistance in series with the inductor may
suffice (see short-circuit calculations at the end of this
section). Alternatively, the 1.5A LT1766 can be used since
it is identical to the LT1956 but runs at a lower frequency
of 200kHz, allowing higher sustained input voltage capa-
bility during output short circuit.
The LT1956 is a current mode controller. It uses the V C
node voltage as an input to a current comparator which
turns off the output switch on a cycle-by-cycle basis as
peak switch current is reached. The internal clamp on the
V C node, nominally 2V, then acts as an output switch peak
current limit. This action becomes the switch current limit
specification. The maximum available output power is
then determined by the switch current limit.
A potential controllability problem could occur under
short-circuit conditions. If the power supply output is
short circuited, the feedback amplifier responds to the low
output voltage by raising the control voltage, V C , to its
peak current limit value. Ideally, the output switch would
be turned on, and then turned off as its current exceeded
the value indicated by V C . However, there is finite response
time involved in both the current comparator and turnoff
of the output switch. These result in a minimum on time
t ON(MIN) . When combined with the large ratio of V IN to
(V F + I ? R), the diode forward voltage plus inductor I ? R
voltage drop, the potential exists for a loss of control.
Expressed mathematically the requirement to maintain
control is:
What has been shown here is that if high inductor ripple
current and discontinuous mode operation can be toler-
ated, small inductor values can be used. If a higher output
f ? t ON ≤
V F + I ? R
V IN
1956f
12
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3414EFE#PBF | IC REG BUCK SYNC ADJ 4A 20TSSOP |
| EBC40DRTI-S13 | CONN EDGECARD 80POS .100 EXTEND |
| LT1054IS8#PBF | IC REG SWITCHD CAP DBL INV 8SOIC |
| LT1766IGN#PBF | IC REG BUCK ADJ 1.5A 16SSOP |
| ESC20DREN-S13 | CONN EDGECARD 40POS .100 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1959 | 制造商:LINER 制造商全称:Linear Technology 功能描述:4.5A, 500kHz Step-Down Switching Regulator |
| LT1959C | 制造商:LINER 制造商全称:Linear Technology 功能描述:4.5A, 500kHz Step-Down Switching Regulator |
| LT1959CR | 功能描述:IC REG BUCK ADJ 4.5A D2PAK RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1959CR#PBF | 功能描述:IC REG BUCK ADJ 4.5A D2PAK RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LT1959CR#TR | 功能描述:IC REG BUCK ADJ 4.5A D2PAK RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
发布紧急采购，3分钟左右您将得到回复。